Product Categories See All
Track Order Status
Sheet 0075771Printer Friendly View
Safety Data Sheet Date of Issue: |Revision Date: 3/19/2015 |Revision Number: Imperial Supplies Part Number: 0075771 SECTION 1: IDENTIFICATION 1.1. Product Identifier Product Form: Product Name: Dynatex� 49294 Clear RTV Silicone Adhesive/Sealant CAS No: Synonyms: N/A. 1.2. Intended Use of the Product Use of the substance/mixture: Refer to Technical Data. 1.3. Name, Address, and Telephone of the Responsible Party Company Dynatex Inc. 350 Ring Road Elizabethtown, KY, 42701 USA Phone: (270) 769-3385 1.4. Emergency Telephone Number Emergency |(800) 424-9300 Chemtrec number | SECTION 2: HAZARDS IDENTIFICATION 2.1. Classification of the Substance or Mixture Classification (GHS-US) N/A | | | 2.2. Label Elements GHS-US Labeling Hazard Pictograms (GHS-US) | | | | | | Signal Word (GHS-US) | Hazard Statements (GHS-US) |N/A. Precautionary Statements |Response: N/A. (GHS-US) |Prevention Use only outdoors or in a well-ventilated |area. |Storage: N/A. |Disposal: N/A. 2.3. Other Hazards Other Hazards Not Contributing to the Classification: Not a hazardous substance or mixture. 2.4. Unknown Acute Toxicity (GHS-US) 0%. SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS 3.1. Substance Name |Product identifier |% |Classification | | |(GHS-US) | | | | | | | | | | | | | | | Full text of H-phrases: See Section 16 3.2. Mixture Name |Product identifier |% |Classification | | |(GHS-US) Ethyltriacetoxysilane |17689-77-9 |1% - 5% | Methyltriacetoxysilane | 4253-34-3 |1% - 5% | | | | | | | | | | SECTION 4: FIRST AID MEASURES 4.1. Description of First Aid Measures First-aid Measures General: First-aid Measures After Inhalation: Material is not likely to present an inhalation hazard at ambient conditions. If material is heated or vapor are generated, care should be taken to prevent inhalation. In case of exposure to vapor, move to fresh air. First-aid Measures After Skin Contact: Remove from skin and wash throughly with soap and water or waterless cleanser. Get medical attention if irritation or other ill effects develop or persist. First-aid Measures After Eye Contact: Rinse with water for 15 minutes. Obtain medical attention. Treat according to person's condition and specifics of exposure. First-aid Measures After Ingestion: No first aid should be needed. 4.2. Most important symptoms and effects, both acute and delayed Symptoms/Injuries: Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: 4.3. Indication of Any Immediate Medical Attention and Special Treatment Needed Comments: Treat according to person's condition and specifics of exposure. SECTION 5: FIRE-FIGHTING MEASURES 5.1. Extinguishing Media Suitable Extinguishing Media: On large fires use dry chemical, foam, or water spray. On small fires use carbon dioxide, dry chemical or water spray. Water can be used to cool fire exposed containers. Unsuitable Extinguishing Media: N/A. 5.2. Special Hazards Arising From the Substance or Mixture Fire Hazard: None known. Explosion Hazard: None known. Reactivity: Comment: When temperatures above 150�C in the presence of air, product can form formaldehyde vapors. Formaldehyde is a potential cancer hazard, a known skin and respiratory sensitizer, and an irritant to the eyes, nose, throat, skin and digestive system. Safe handling conditions may be maintained by keeping vapor concentrations within the OSHA Permissible Exposure Limits for formaldehyde. 5.3. Advice for Firefighters Precautionary Measures Fire: Firefighting Instructions: Self-contained breathing apparatus and protective clothing should be worn when fighting large fires involving chemicals. Determine the need to evacuate or isolate the area according to your local emergency plan. Use water spray to keep fire exposed containers cool. Protection During Firefighting: SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal Precautions, Protective Equipment and Emergency Procedures General Measures: 6.1.1. For Non-emergency Personnel Protective Equipment: Emergency Procedures: 6.1.2. For Emergency Responders Protective Equipment: Emergency Procedures: 6.2. Environmental Precautions 6.3. Methods and Material for Containment and Cleaning Up For Containment: Methods for Cleaning Up: Steps to be taken in Case of spill or release: Observe all personal protection equipment recommendations. Wipe up or scrape up and contain for salvage or disposal. Clean area as appropriate since spilled materials, even in small quantities, may present a slip hazard. Final cleaning may require steam, solvents or detergents. Dispose of saturated absorbant or cleaning materia appropriately, since spontaneous heating may occur. Local, state and federal laws and regulations may apply to releases and disposal of this material, as well as those materials and items employed in the cleanup of releases. You will need to determine which federal, state and local laws and regulations are applicable. Sections 13 and 15 of this MSDS provide information regarding certain federal and state requirements. 6.4. Reference to Other Sections See heading 8, Exposure Controls and Personal Protection. SECTION 7: HANDLING AND STORAGE 7.1. Precautions for Safe Handling Additional Hazards When Processed: Use with adequate ventilation. Product evolves acetic acid with exposed to water or humid air. Provide ventilation during use to control acetic acid with exposure guidelines or use respiratory protection. Avoid eye contact. Avoid skin contact. Do not take internally. Avoid breathing vapor. Keep container closed. Hygiene Measures: 7.2. Conditions for Safe Storage, Including Any Incompatibilities Technical Measures: Storage Conditions: Use reasonable care and store away from oxidizing materials. Keep container closed and store away from water or moisture. This material in its finely divided form presents an explosion hazard. Follow NFPA 654 (for chemical dusts) or 484 (for metal dusts) as appropriate for managing dust hazards to minimize secondary explosion potential. 7.3. Specific End Use(s) SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1. Control Parameters Occupational Exposure Limits: Ingredient Name ACGIH TLV OSHA PEL STEL Ethyltriacetoxysilane TWA 10ppm TWA 10ppm 15ppm Methyltriacetoxysilane TWA 10ppm TWA 10ppm 15ppm Component Exposure Limits: Component Name: Ethyltriacetoxysilane CAS Number: 17689-77-9 Exposure Limits: See acetic acid comments Component Name: Methyltriacetoxysilane CAS Number: 4253-34-3 Exposure Limits: See acetic acid comments Acetic acid is formed upon contact with water or humid air. Provide adequate ventilation to control exposures within guidelines of OSHA PEL: TWA 10 ppm and ACGIH TLV: TWA 10 ppm, STEL 15 ppm. 8.2. Exposure Controls Appropriate Engineering |Local Ventilation: Recommended General Ventilation: Controls |Recommended. |Comment: Product evolves acetic acid when exposed to |water or humid air. |Provide ventilation during use to control acetic |acid within exposure guidelines or use respiratory |protection. When heated to temperatures above 150C |(300F) in the presence of air, product can form |formaldehyde vapors. Physical and health hazard |information is readily available on the Material |Safety Data Sheet. |Note: These precautions are for room temperature |handling. Use at elevated temperatures or |aerosol/spray applications may require added |precautions. Personal Protective Equipment|Goggles, Gloves. |Precautionary Measures: Avoid eye contact. Avoid |skin contact. Avoid breathing vapor. Keep container |closed. Do not take internally. Use reasonable care. Materials for Protective | Clothing | Hand Protection | Eye Protection |Use proper protection - safety glasses as a minimum. Skin and Body Protection |Wash at mealtimes and end of shift. Contaminated |clothing and shoes should be removed as soon as |practical and throughly cleaned before reuse. |Chemical protective gloves are recommended. Suitable |Gloves: Handle in accordance with good industrial |hygiene and safety practices. Respiratory Protection |Use respiratory protection unless adequate exhaust |ventilation is provided or exposure assessment |demonstrates that exposures are within exposure |guidelines. Industrial Hygiene Personnel can assist |in judging the adequacy of existing engineering |controls. |Suitable Respirator: Respiratory protection is not |needed under ambient conditions. If vapor is |generated when material is heated or handled, the |following is advised. General and local exhaust |ventilation is recommended to maintain vapor |exposures below recommended limits. Where |concentrations are above recommended limits or are |unknown, appropriate respiratory protection should |be worn. Follow OSHA respirator regulations (29 CFR |1910.134) and use |NIOSH/MSHA approved respirators. Thermal Hazard Protection | SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1. Information on Basic Physical and Chemical Properties Physical State |Paste Appearance | Odor |Acetic Acid Odor Threshold |N/A pH |Not Determined Relative Evaporation Rate |Not Determined (butylacetate=1) | Melting Point |Not Determined Freezing Point | Boiling Point |Not Determined Flash Point |>212F />100C Closed Cup Auto-ignition Temperature |N/A Decomposition Temperature |N/A Flammability (solid, gas) |N/A Vapor Pressure |Not Determined Relative Vapor Density at 20 �C |Not Determined Relative Density | Specific Gravity |1.007 Solubility |Not Determined Partition coefficient: |N/A n-octanol/water | Viscosity |Not Determined Lower Flammable Limit |N/A Upper Flammable Limit |N/A 9.2. Other Information Note: The above information is not intended for use in preparing product specifications. Contact Accumetric LLC before writing specifications. SECTION 10: STABILITY AND REACTIVITY 10.1 Reactivity 10.2 Chemical Stability Stable. 10.3 Possibility of Hazardous Reactions Hazardous Polymerization: Will not occur. 10.4 Conditions to Avoid None known. 10.5 Incompatible Materials Oxidizing material can cause a reaction. Water, moisture or humid air can cause hazardous vapors to form as described in Section 8. 10.6 Hazardous Decomposition Products Thermal breakdown of this product during fire or very high heat conditions may evolve the following hazardous decomposition products: Carbon oxides and traces of incompletely burned carbon compounds Formaldehyde Silicon dioxide. SECTION 11: TOXICOLOGICAL INFORMATION 11.1. Information on Toxicological Effects Acute Toxicity: Component Toxicology Information: No known applicable information. Special Hazard Information on Components: No known applicable information. Skin Corrosion/Irritation: Serious Eye Damage/Irritation: Respiratory or Skin Sensitization: Germ Cell Mutagenicity: Carcinogenicity: Reproductive Toxicity: Specific Target Organ Toxicity (Single Exposure): Specific Target Organ Toxicity (Repeated Exposure): Aspiration Hazard: Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: SECTION 12: ECOLOGICAL INFORMATION 12.1. Toxicity 12.2. Persistence and Degradability 12.3. Bioaccumulative Potential 12.4. Mobility in Soil 12.5. Other Adverse Effects Environmental Effects: Complete information is not yet available. Environmental Fate and Distribution: Complete information is not yet available. Fate and Effects in Waste Water Treatment Plants: Complete information is not yet available. SECTION 13: DISPOSAL CONSIDERATIONS 13.1. Waste treatment methods Waste Disposal Recommendations: We make no guarantee or warranty of any kind that the use or disposal of this product complies with all local, state, or federal laws. It is also the obligation of each user of the product mentioned herein to determine and comply with the requirements of all applicable statutes. This product is not known to be regulated under RCRA regulations. Disposal of unused portions of this product and process waste containing this product should be done only after a careful evaluation and in compliance with all federal, local and state laws. Additional Information: SECTION 14: TRANSPORT INFORMATION 14.1 In Accordance with DOT Proper Shipping Name |N/A Hazard Class |N/A |<PICTOGRAM PHRASE> Identification Number|N/A | Label Codes | | ERG Number | 14.2 In Accordance with IMDG Proper Shipping Name |Not subject to IMDG code. Hazard Class | Identification Number| Label Codes | |<PICTOGRAM PHRASE> ntification Of The | | Substance/m | | EmS-No. (Fire) | | EmS-No. (Spillage) | | 14.3 In Accordance with IATA Proper Shipping Name |Not subject to IATA regulations. Identification Number| |<PICTOGRAM PHRASE> Hazard Class | | Label Codes | | ntification Of The | | Substance/m | | ERG Code (IATA) | SECTION 15: REGULATORY INFORMATION 15.1 US Federal Regulations <COMPONENT> The contents of this MSDS comply with the OSHA Hazard Communication Standard 29 CFR 1910.1200. SARA Title III Section 302 Extremely Hazardous Substances: None. SARA Titre III Section 304 CERCLA Substances dangereuses: None. SARA Title III Section 313 Toxic Chemicals: None present or none present in regulated quantities. SARA Section 311/312 Hazard Classes |Acute: Yes |Chronic: No |Fire: No |Pressure: No |Reactive: No Toxic Substances Control Act (TSCA) |All chemical substances found in this product |comply with the Toxic Substances Control Act |inventory reporting requirements. 15.2 US State Regulations <COMPONENT> California Proposition 65: This product contains the following chemical(s) listed by the State of California under the Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65) as being known to cause cancer, birth defects or other reproductive harm: None known. Massachusetts: Silica, amorphous (7631-86-9) Depending on color, may also contain: Titanium dioxide (13463-67-7). New Jersey: Dimethyl siloxane, hydroxy-terminated (70131-67-8) Ethyltriacetoxysilane (17689-77-9) Methyltriacetoxysilane (4253-34-3) Silica, amorphous (7631-86-9) Hydrotreated middle petroleum distillates (64742-46-7). Pennsylvania: Dimethyl siloxane, hydroxy-terminated (70131-67-8) Silica, amorphous (7631-86-9) Hydrotreated middle petroleum distillates (64742-46-7). SECTION 16: OTHER INFORMATION, INCLUDING DATE OF PREPARATION OR LAST REVISION Revision date |3/19/2015 Other |This document has been prepared in accordance with the SDS Information |requirements of the OSHA Hazard Communication Standard 29 CFR |1910.1200. GHS Full Text Phrases: ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | Grainger disclaimer.
The information contained in this was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this '' shall be created or inferred by any statement in this ''. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this ''. The user is responsible for full compliance.