Product Categories See All
Track Order Status
SDS Sheet 0067660Printer Friendly View
SECTION 1: IDENTIFICATION 1.1. Product Identifier Product Form: Product Name: MystikÂ® JT-6Â® Lo-Temp Extreme Grease CAS No: Synonyms: Lubricating grease; CITGOÂ® Material Code: 665027002 1.2. Intended Use of the Product Use of the substance/mixture: 1.3. Name, Address, and Telephone of the Responsible Party Company CITGO Petroleum Corporation P.O. Box 4689 Houston, TX 77210 email@example.com Phone: 1.4. Emergency Telephone Number Emergency | (800) 248-4684, (832) 486-4700, (800) 424-9300 (United States number |Only) SECTION 2: HAZARDS IDENTIFICATION 2.1. Classification of the Substance or Mixture Classification (GHS-US) Not classified| | | 2.2. Label Elements GHS-US Labeling Hazard Pictograms (GHS-US) | | | | | | Signal Word (GHS-US) |Warning Hazard Statements (GHS-US) |Injection under the skin can cause severe injury. |Most damage occurs in the first few hours. |Initial symptoms may be minimal. Precautionary Statements |General: (GHS-US) |Avoid contact with eyes, skin and clothing. May be |harmful if swallowed. IF IN EYES: Rinse cautiously |with water for several minutes. IF SWALLOWED: Do NOT |induce vomiting. After handling, always wash hands |thoroughly with soap and water. If you feel unwell, |seek medical attention and show the label when |possible. Keep out of reach of children. |Prevention |Not applicable. |Response |Not applicable. |Storage |Store in a dry place and/or in closed container. |Store in accordance with all local, regional, |national and international regulations. |Disposal |Dispose of contents and container in accordance with |all local, regional, national and international |regulations. 2.3. Other Hazards Other Hazards Not Contributing to the Classification: Injection of petroleum hydrocarbons requires immediate medical attention. 2.4. Unknown Acute Toxicity (GHS-US) SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS 3.1. Substance Name |Product identifier |% |Classification | | |(GHS-US) | | | | | | | | | | | | | | | Full text of H-phrases: See Section 16 3.2. Mixture Name |Product identifier |% |Classification | | |(GHS-US) Any concentration shown as a |Not applicable. | | range is to protect | | | confidentiality or is due to | | | process variation. | | | | | | | | | | | | | | | SECTION 4: FIRST AID MEASURES 4.1. Description of First Aid Measures First-aid Measures General: First-aid Measures After Inhalation: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Get medical attention if symptoms occur. First-aid Measures After Skin Contact: Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Get medical attention if symptoms occur. First-aid Measures After Eye Contact: Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Get medical attention if irritation occurs. First-aid Measures After Ingestion: Wash out mouth with water. Remove victim to fresh air and keep at rest in a position comfortable for breathing. Do not induce vomiting unless directed to do so by medical personnel. Get medical attention if symptoms occur. 4.2. Most important symptoms and effects, both acute and delayed Symptoms/Injuries: Symptoms/Injuries After Inhalation: Most important symptoms/effects, acute: No known significant effects or critical hazards. Over-exposure signs/symptoms: No specific data. Symptoms/Injuries After Skin Contact: Most important symptoms/effects, acute: Injection of pressurized hydrocarbons can cause severe permanent tissue damage. Initial symptoms may be minor. Over-exposure signs/symptoms: No specific data. Symptoms/Injuries After Eye Contact: Most important symptoms/effects, acute: No known significant effects or critical hazards. Over-exposure signs/symptoms: No specific data. Symptoms/Injuries After Ingestion: Most important symptoms/effects, acute: No known significant effects or critical hazards. Over-exposure signs/symptoms: No specific data. Chronic Symptoms: 4.3. Indication of Any Immediate Medical Attention and Special Treatment Needed Notes to physician: Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled. Specific treatments: Treat symptomatically and supportively. Protection of first-aiders: No action shall be taken involving any personal risk or without suitable training. SECTION 5: FIRE-FIGHTING MEASURES 5.1. Extinguishing Media Suitable Extinguishing Media: Use an extinguishing agent suitable for the surrounding fire. Unsuitable Extinguishing Media: None known. 5.2. Special Hazards Arising From the Substance or Mixture Fire Hazard: No specific fire or explosion hazard. Explosion Hazard: Decomposition products may include the following materials: carbon dioxide, carbon monoxide, sulfur oxides, metal oxide/oxides. Reactivity: 5.3. Advice for Firefighters Precautionary Measures Fire: Firefighting Instructions: Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Protection During Firefighting: Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal Precautions, Protective Equipment and Emergency Procedures General Measures: 6.1.1. For Non-emergency Personnel Protective Equipment: No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Put on appropriate personal protective equipment. Emergency Procedures: If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For nonemergency personnel". 6.1.2. For Emergency Responders Protective Equipment: Emergency Procedures: 6.2. Environmental Precautions Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). 6.3. Methods and Material for Containment and Cleaning Up For Containment: Methods for Cleaning Up: Small spill: Move containers from spill area. Vacuum or sweep up material and place in a designated, labeled waste container. Dispose of via a licensed waste disposal contractor. Large spill: Move containers from spill area. Prevent entry into sewers, water courses, basements or confined areas. Vacuum or sweep up material and place in a designated, labeled waste container. Dispose of via a licensed waste disposal contractor. Note: see Section 1 for emergency contact information and Section 13 for waste disposal. 6.4. Reference to Other Sections See heading 8, Exposure Controls and Personal Protection. SECTION 7: HANDLING AND STORAGE 7.1. Precautions for Safe Handling Additional Hazards When Processed: Put on appropriate personal protective equipment (see Section 8). Hygiene Measures: Advice on general occupational hygiene: Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures. Individual protection measures: Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location. 7.2. Conditions for Safe Storage, Including Any Incompatibilities Technical Measures: Storage Conditions: Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. Bulk Storage Conditions: Do not apply heat or flame to stockpiled material. Rotate stock to reduce the potential for hot spots. Do not store with oxidizers. Minimize dust creation by keeping material moist and/or covered. 7.3. Specific End Use(s) SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1. Control Parameters Occupational exposure limits: None identified. 8.2. Exposure Controls Appropriate Engineering |Good general ventilation should be sufficient to Controls |control worker exposure to airborne contaminants. Personal Protective Equipment|Environmental exposure controls: Emissions from |ventilation or work process equipment should be |checked to ensure they comply with the requirements |of environmental protection legislation. In some |cases, vapor controls, filters or engineering |modifications to the process equipment will be |necessary to reduce emissions to acceptable levels. Materials for Protective | Clothing | Hand Protection |Chemical-resistant gloves complying with an approved |standard should be worn at all times when handling |chemical products if a risk assessment indicates |this is necessary. Eye Protection |Safety glasses equipped with side shields are |recommended as minimum protection in industrial |settings. If contact is possible, the following |protection should be worn, unless the assessment |indicates a higher degree of protection: Safety |glasses with side shields. Safety eyewear complying |with an approved standard should be used when a risk |assessment indicates this is necessary to avoid |exposure to liquid splashes, mists, gases or dusts. |If inhalation hazards exist, a full-face respirator |may be required instead. Skin and Body Protection |Body protection: Personal protective equipment for |the body should be selected based on the task being |performed and the risks involved and should be |approved by a specialist before handling this |product. |Other skin protection: Appropriate footwear and any |additional skin protection measures should be |selected based on the task being performed and the |risks involved and should be approved by a |specialist before handling this product. Respiratory Protection |Use a properly fitted, particulate filter respirator |complying with an approved standard if a risk |assessment indicates this is necessary. Respirator |selection must be based on known or anticipated |exposure levels, the hazards of the product and the |safe working limits of the selected respirator. Thermal Hazard Protection | SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1. Information on Basic Physical and Chemical Properties Physical State |Solid. [Smooth texture] Appearance | Odor |Petroleum. Odor Threshold |Not available. pH |Not available. Relative Evaporation Rate |<1 (n-butyl acetate. = 1) (butylacetate=1) | Melting Point | Freezing Point | Boiling Point |Not available. Flash Point |Open cup: >150Â°C (>302Â°F) Auto-ignition Temperature | Decomposition Temperature | Flammability (solid, gas) | Vapor Pressure |<0.0013 kPa (<0.01 mm Hg) [room temperature] Relative Vapor Density at 20 Â°C | Relative Density |0.91 Specific Gravity | Solubility |Insoluble in the following materials: cold |water. Partition coefficient: | n-octanol/water | Viscosity | Lower Flammable Limit |Lower: 1% Upper Flammable Limit |Upper: 7% 9.2. Other Information SECTION 10: STABILITY AND REACTIVITY 10.1 Reactivity Not expected to be Explosive, Self-Reactive, Self-Heating, or an Organic Peroxide under US GHS Definition(s). 10.2 Chemical Stability The product is stable. 10.3 Possibility of Hazardous Reactions Under normal conditions of storage and use, hazardous reactions will not occur. 10.4 Conditions to Avoid No specific data. 10.5 Incompatible Materials No specific data. 10.6 Hazardous Decomposition Products Under normal conditions of storage and use, hazardous decomposition products should not be produced. SECTION 11: TOXICOLOGICAL INFORMATION 11.1. Information on Toxicological Effects Acute Toxicity: Distillates (petroleum), hydrotreated heavy paraffinic: Mineral oil mists derived from highly refined oils are reported to have low acute and sub-acute toxicities in animals. Effects from single and short-term repeated exposures to high concentrations of mineral oil mists well above applicable workplace exposure levels include lung inflammatory reaction, lipoid granuloma formation and lipoid pneumonia. In acute and sub-acute studies involving exposures to lower concentrations of mineral oil mists at or near current work place exposure levels produced no significant toxicological effects. Skin Corrosion/Irritation: No additional information. Serious Eye Damage/Irritation: No additional information. Respiratory or Skin Sensitization: Skin: No additional information. Respiratory: No additional information. Germ Cell Mutagenicity: No additional information. Carcinogenicity: No additional information. Reproductive Toxicity: No additional information. Specific Target Organ Toxicity (Single Exposure): Not available. Specific Target Organ Toxicity (Repeated Exposure): Not available. Aspiration Hazard: Not available. Symptoms/Injuries After Inhalation: No specific data. Symptoms/Injuries After Skin Contact: No specific data. Injection of pressurized hydrocarbons can cause severe permanent tissue damage. Initial symptoms may be minor. Symptoms/Injuries After Eye Contact: No specific data. Symptoms/Injuries After Ingestion: No specific data. Chronic Symptoms: SECTION 12: ECOLOGICAL INFORMATION 12.1. Toxicity Not available. 12.2. Persistence and Degradability Not available. 12.3. Bioaccumulative Potential Not available. 12.4. Mobility in Soil Not available. 12.5. Other Adverse Effects No known significant effects or critical hazards. SECTION 13: DISPOSAL CONSIDERATIONS 13.1. Waste treatment methods Waste Disposal Recommendations: The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. This material and its container must be disposed of in a safe way. Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Additional Information: SECTION 14: TRANSPORT INFORMATION 14.1 In Accordance with DOT Proper Shipping Name | - Hazard Class | - |<PICTOGRAM PHRASE> Identification Number|Not regulated. | Label Codes | | ERG Number | 14.2 In Accordance with IMDG Proper Shipping Name |Not available. Hazard Class |Not available. Identification Number|Not available. Label Codes | |<PICTOGRAM PHRASE> ntification Of The | | Substance/m | | EmS-No. (Fire) | | EmS-No. (Spillage) | | 14.3 In Accordance with IATA Proper Shipping Name |Not available. Identification Number|Not available. |<PICTOGRAM PHRASE> Hazard Class |Not available. | Label Codes | | ntification Of The | | Substance/m | | ERG Code (IATA) | SECTION 15: REGULATORY INFORMATION 15.1 US Federal Regulations U.S. Federal regulations Clean Water Act (CWA) 307: Antimony & Antimony Compounds This material is classified as an oil under Section 311 of the Clean Water Act (CWA) and the Oil Pollution Act of 1990 (OPA). Discharges or spills which produce a visible sheen on waters of the United States, their adjoining shorelines, or into conduits leading to surface waters must be reported to the EPA's National Response Center at (800) 424-8802. SARA 302/304 Composition/information on ingredients SARA 304 RQ: Not applicable. SARA Section 311/312 Hazard Classes |Not applicable. Toxic Substances Control Act (TSCA) |United States inventory (TSCA 8b): All |components are listed or exempted. 15.2 US State Regulations State regulations Massachusetts: :None of the components are listed. New York : None of the components are listed. New Jersey : None of the components are listed. Pennsylvania : None of the components are listed. SECTION 16: OTHER INFORMATION, INCLUDING DATE OF PREPARATION OR LAST REVISION Revision date |11/4/2014 Other |This document has been prepared in accordance with the SDS Information |requirements of the OSHA Hazard Communication Standard 29 CFR |1910.1200. GHS Full Text Phrases: ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | Grainger disclaimer.
The information contained in this SDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'SDS' shall be created or inferred by any statement in this 'SDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'SDS'. The user is responsible for full compliance.