Product Categories See All
Track Order Status
SDS Sheet 0066880Printer Friendly View
SECTION 1: IDENTIFICATION 1.1. Product Identifier Product Form: Aerosol. Product Name: Freeze-OffÂ® Super Penetrant CAS No: Synonyms: 1.2. Intended Use of the Product Use of the substance/mixture: Penetrant 1.3. Name, Address, and Telephone of the Responsible Party Company : CRC Industries, Inc. 885 Louis Dr. Warminster, PA 18974 US T-215-674-4300, 800-521-3168 1.4. Emergency Telephone Number Emergency | 800-424-9300 (US), 800-424-9300 (US) number |703-527-3887 (International) SECTION 2: HAZARDS IDENTIFICATION 2.1. Classification of the Substance or Mixture Classification (GHS-US) Flammable |Category 1 aerosols | Gases under |Liquefied gas pressure | Skin |Category 2 corrosion/irri| tation | Serious eye |Category 2A damage/eye | irritation | Sensitization,|Category 1 skin | Specific |Category 3 target organ |respiratory toxicity, |tract single |irritation exposure | Specific |Category 2 target organ | toxicity, | repeated | exposure | Aspiration |Category 1 hazard | Hazardous to |Category 3 the aquatic | environment, | long-term | hazard | 2.2. Label Elements GHS-US Labeling Hazard Pictograms (GHS-US) |Flame |Gas Cylinder |Health Hazard |Exclamation Mark Signal Word (GHS-US) |Danger Hazard Statements (GHS-US) |Extremely flammable aerosol. Contains gas under |pressure; may explode if heated. May be fatal if |swallowed and enters airways. Causes skin |irritation. May cause an allergic skin reaction. |Causes serious eye irritation. May cause respiratory |irritation. May cause damage to organs through |prolonged or repeated exposure. Harmful to aquatic |life with long lasting effects. Precautionary Statements |Prevention: (GHS-US) |Keep away from heat/sparks/open flames/hot surfaces. |- No smoking. Do not spray on an open flame or other |ignition source. Do not apply while equipment is |energized. Pressurized container: Do not pierce or |burn, even after use. Extinguish all flames, pilot |lights and heaters. Vapors will accumulate readily |and may ignite. Use only with adequate ventilation; |maintain ventilation during |use and until all vapors are gone. Open doors and |windows or use other means to ensure a fresh air |supply during use and while product is drying. If |you experience any symptoms listed on this label, |increase ventilation or leave the area. Do not |breathe gas, mist or vapor. Contaminated work |clothing must not be allowed out of the workplace. |Wear protective gloves and eye/face protection. Wash |hands thoroughly after handling. Avoid release to |the environment. |Response: |If swallowed: Immediately call a poison |center/doctor. Do NOT induce vomiting. If on skin: |Wash with plenty of water. If skin irritation or |rash occurs: Get medical attention. Take off |contaminated clothing and wash before reuse. If |inhaled: Remove person to fresh air and keep |comfortable for breathing. Call a poison |center/doctor if you feel unwell. If in eyes: Rinse |cautiously with water for several minutes. Remove |contact lenses, if present and easy to do. Continue |rinsing. If eye irritation persists: Get medical |attention. |Storage: |Store locked up. Store in a well-ventilated place. |Protect from sunlight. Do not expose to temperatures |exceeding 50Â°C/122Â°F. Exposure to high temperature |may cause can to burst. |Disposal: |Dispose of contents/container in accordance with |local/regional/national regulations 2.3. Other Hazards Other Hazards Not Contributing to the Classification: Static accumulating flammable liquid can become electrostatically charged even in bonded and grounded equipment. Sparks may ignite liquid and vapor. May cause flash fire or explosion. 2.4. Unknown Acute Toxicity (GHS-US) 87.51% of the mixture consists of component(s) of unknown long-term hazards to the aquatic environment. SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS 3.1. Substance Name |Product identifier |% |Classification | | |(GHS-US) | | | | | | | | | | | | | | | Full text of H-phrases: See Section 16 3.2. Mixture Name |Product identifier |% |Classification | | |(GHS-US) 1,1-Difluoroethane |75-37-6 |40 - 50 | Distillates (petroleum), |64742-46-7 |20 - 30 | hydrotreated middle | | | Distillates (petroleum), |64742-47-8 |5 - 10 | hydrotreated light | | | Turpentine, oil |8006-64-2 |5 - 10 | COzolÂ® 306 |Proprietary |4 - 6 | Stoddard Solvent |8052-41-3 |3 - 5 | 2-Butoxyethanol |111-76-2 |1 - 3 | 4-Hydroxy-4-methylpentan-2-one |123-42-2 |1 - 3 | (Diacetone alcohol) | | | SECTION 4: FIRST AID MEASURES 4.1. Description of First Aid Measures First-aid Measures General: Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves. Wash contaminated clothing before reuse. First-aid Measures After Inhalation: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or doctor/physician if you feel unwell. First-aid Measures After Skin Contact: Remove contaminated clothing immediately and wash skin with soap and water. In case of eczema or other skin disorders: Seek medical attention and take along these instructions. Wash contaminated clothing before reuse. First-aid Measures After Eye Contact: Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get medical attention if irritation develops and persists. First-aid Measures After Ingestion: Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs. Aspiration may cause pulmonary edema and pneumonitis. 4.2. Most important symptoms and effects, both acute and delayed Symptoms/Injuries: Symptoms may include stinging, tearing, redness, swelling, and blurred vision. May cause an allergic skin reaction. Dermatitis. Rash. May cause redness and pain. Prolonged exposure may cause chronic effects. Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: 4.3. Indication of Any Immediate Medical Attention and Special Treatment Needed Provide general supportive measures and treat symptomatically. Keep victim under observation. Symptoms may be delayed. SECTION 5: FIRE-FIGHTING MEASURES 5.1. Extinguishing Media Suitable Extinguishing Media: Water spray. Water fog. Foam. Dry chemical powder, carbon dioxide, sand or earth may be used for small fires only. Unsuitable Extinguishing Media: Do not use water jet as an extinguisher, as this will spread the fire. 5.2. Special Hazards Arising From the Substance or Mixture Fire Hazard: Extremely flammable aerosol. Explosion Hazard: Contents under pressure. Pressurized container may explode when exposed to heat or flame. This product is a poor conductor of electricity and can become electrostatically charged. If sufficient charge is accumulated, ignition of flammable mixtures can occur. Static electricity accumulation may be significantly increased by the presence of small quantities of water or other contaminants. Material will float and may ignite on surface of water. Reactivity: 5.3. Advice for Firefighters Precautionary Measures Fire: Firefighting Instructions: In case of fire: Stop leak if safe to do so. Do not move cargo or vehicle if cargo has been exposed to heat. If tank, rail car or tank truck is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also consider initial evacuation for 800 meters (1/2 mile) in all directions. ALWAYS stay away from tanks engulfed in flame. Move containers from fire area if you can do so without risk. Containers should be cooled with water to prevent vapor pressure build up. For massive fire in cargo area, use unmanned hose holder or monitor nozzles, if possible. If not, withdraw and let fire burn out. Protection During Firefighting: Firefighters must use standard protective equipment including flame retardant coat, helmet with face shield, gloves, rubber boots, and in enclosed spaces, SCBA. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal Precautions, Protective Equipment and Emergency Procedures General Measures: Emergency Procedures: Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of low areas. Remove all possible sources of ignition in the surrounding area. Wear appropriate protective equipment and clothing during clean-up. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Do not breathe gas, mist or vapor. Ventilate closed spaces before entering them. Use appropriate containment to avoid environmental contamination. Transfer by mechanical means such as vacuum truck to a salvage tank or other suitable container for recovery or safe disposal. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS. 6.1.1. For Non-emergency Personnel Protective Equipment: Emergency Procedures: 6.1.2. For Emergency Responders Protective Equipment: 6.2. Environmental Precautions Avoid release to the environment. Contact local authorities in case of spillage to drain/aquatic environment. Prevent further leakage or spillage if safe to do so. Do not contaminate water. Avoid discharge into drains, water courses or onto the ground. Use appropriate containment to avoid environmental contamination. 6.3. Methods and Material for Containment and Cleaning Up For Containment: Methods for Cleaning Up: Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep combustibles (wood, paper, oil, etc.) away from spilled material. Large Spills: Stop leak if you can do so without risk. Move the cylinder to a safe and open area if the leak is irreparable. Isolate area until gas has dispersed. Dike the spilled material, where this is possible. Cover with plastic sheet to prevent spreading. Absorb in vermiculite, dry sand or earth and place into containers. Scoop up used absorbent into drums or other appropriate container. Prevent entry into waterways, sewer, basements or confined areas. Following product recovery, flush area with water. Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination. Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS. 6.4. Reference to Other Sections See heading 8, Exposure Controls and Personal Protection. SECTION 7: HANDLING AND STORAGE 7.1. Precautions for Safe Handling Additional Hazards When Processed: Minimize fire risks from flammable and combustible materials (including combustible dust and static accumulating liquids) or dangerous reactions with incompatible materials. Handling operations that can promote accumulation of static charges include but are not limited to: mixing, filtering, pumping at high flow rates, splash filling, creating mists or sprays, tank and container filling, tank cleaning, sampling, gauging, switch loading, vacuum truck operations. Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or expose containers to heat, flame, sparks, or other sources of ignition. Use caution around energized equipment. The metal container will conduct electricity if it contacts a live source. This may result in injury to the user from electrical shock and/or flash fire. Do not re-use empty containers. Do not breathe mist or vapor. Do not breathe gas. Do not get this material in contact with skin. Avoid contact with eyes. Avoid prolonged exposure. Avoid contact with clothing. Use only in well-ventilated areas. Wear appropriate personal protective equipment. Wash hands thoroughly after handling. Observe good industrial hygiene practices. Avoid release to the environment. Do not empty into drains. For product usage instructions, please see the product label. Hygiene Measures: When using, do not eat, drink or smoke. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Contaminated work clothing should not be allowed out of the workplace. 7.2. Conditions for Safe Storage, Including Any Incompatibilities Technical Measures: Storage Conditions: Store in a well-ventilated place. Pressurized container. Protect from sunlight and do not expose to temperatures exceeding 50Â°C/122 Â°F. Do not puncture, incinerate or crush. Do not handle or store near an open flame, heat or other sources of ignition. This material can accumulate static charge which may cause spark and become an ignition source. Avoid spark promoters. These alone may be insufficient to remove static electricity. Store away from incompatible materials (see Section 10 of the SDS). Keep out of the reach of children. 7.3. Specific End Use(s) SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1. Control Parameters Occupational exposure limits US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) Components Type Value Form 2-Butoxyethanol (CAS 111-76-2) PEL 240 mg/m3 50 ppm 4-Hydroxy-4-methylpentan- PEL 240 mg/m3 2-one (Diacetone alcohol)(CAS 123-42-2) Distillates (petroleum), PEL 5 mg/m3 Mist. hydrotreated middle (CAS64742-46-7) Distillates (petroleum), PEL 5 mg/m3 Mist. hydrotreated middle (CAS 64742-46-7) Stoddard Solvent (CAS 8052-41-3) PEL 2900 mg/m3 500 ppm Turpentine, oil (CAS 8006-64-2) PEL 560 mg/m3 100 ppm US. ACGIH Threshold Limit Values Components Type Value Form 2-Butoxyethanol (CAS 111-76-2) TWA 20 ppm 4-Hydroxy-4-methylpentan- TWA 50 ppm 2-one (Diacetone alcohol) (CAS 123-42-2) Distillates (petroleum), TWA 5 mg/m3 Inhalable fraction. hydrotreated middle (CAS 64742-46-7) Stoddard Solvent (CAS 8052-41-3) TWA 100 ppm Turpentine, oil (CAS 8006-64-2) TWA 20 ppm US. NIOSH: Pocket Guide to Chemical Hazards Components Type Value Form 2-Butoxyethanol (CAS 111-76-2) TWA 24 mg/m3 5 ppm 4-Hydroxy-4-methylpentan- TWA 240 mg/m3 2-one (Diacetone alcohol)(CAS 123-42-2) 50 ppm Distillates (petroleum), TWA 100 mg/m3 hydrotreated light (CAS64742-47-8) Distillates (petroleum), STEL 10 mg/m3 Mist. hydrotreated middle (CAS64742-46-7) TWA 5 mg/m3 Mist. Stoddard Solvent (CAS 8052-41-3) Ceiling 1800 mg/m3 TWA 350 mg/m3 Turpentine, oil (CAS 8006-64-2) TWA 560 mg/m3 100 ppm US. AIHA Workplace Environmental Exposure Level (WEEL) Guides Components Type Value 1,1-Difluoroethane (CAS 75-37-6) TWA 2700 mg/m3 1000 ppm 8.2. Exposure Controls Appropriate Engineering |Good general ventilation (typically 10 air changes Controls |per hour) should be used. Ventilation rates should |be matched to conditions. If applicable, use process |enclosures, local exhaust ventilation, or other |engineering controls to maintain airborne levels |below recommended exposure limits. If exposure |limits have not been established, maintain airborne |levels to an acceptable level. Eye wash facilities |and emergency shower must be available when handling |this product. Personal Protective Equipment| Materials for Protective | Clothing | Hand Protection |Wear protective gloves: Nitrile. Rubber. Eye Protection |Wear safety glasses with side shields (or goggles). Skin and Body Protection |Wear appropriate chemical resistant clothing. Respiratory Protection |Wear positive pressure self-contained breathing |apparatus (SCBA). Air monitoring is needed to |determine actual employee exposure levels. Thermal Hazard Protection |Wear appropriate thermal protective clothing, when |necessary. SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1. Information on Basic Physical and Chemical Properties Physical State |Liquid. Appearance | Odor |Pine. Odor Threshold |Not available. pH |Not available. Relative Evaporation Rate |Slow. (butylacetate=1) | Melting Point |-103 Â°F (-75 Â°C) estimated Freezing Point |-103 Â°F (-75 Â°C) estimated Boiling Point |311 Â°F (155 Â°C) estimated Flash Point |126 Â°F (52.2 Â°C) Tag Closed Cup Auto-ignition Temperature |446 Â°F (230 Â°C) estimated Decomposition Temperature |Not available. Flammability (solid, gas) |Not available. Vapor Pressure |5273.9 hPa estimated Relative Vapor Density at 20 Â°C | Relative Density |0.88 estimated Specific Gravity | Solubility |Not available. Partition coefficient: |Not available. n-octanol/water | Viscosity |Not available. Lower Flammable Limit |0.6 % estimated Upper Flammable Limit |10.6 % estimated 9.2. Other Information Percent volatile 100 % estimated VOC content (CA) 24.1 % VOC content (OTC) 24.1 % VOC content (40 CFR 51.100(s)): 50 % SECTION 10: STABILITY AND REACTIVITY 10.1 Reactivity The product is stable and non-reactive under normal conditions of use, storage and transport. 10.2 Chemical Stability Material is stable under normal conditions. 10.3 Possibility of Hazardous Reactions No dangerous reaction known under conditions of normal use. 10.4 Conditions to Avoid Avoid temperatures exceeding the flash point. Contact with incompatible materials. 10.5 Incompatible Materials Strong oxidizing agents. Chlorine. 10.6 Hazardous Decomposition Products Carbon oxides. SECTION 11: TOXICOLOGICAL INFORMATION 11.1. Information on Toxicological Effects Acute Toxicity: May be fatal if swallowed and enters airways. May cause an allergic skin reaction. May cause respiratory irritation. Skin Corrosion/Irritation: Causes skin irritation. Serious Eye Damage/Irritation: Causes serious eye irritation. Respiratory or Skin Sensitization: Not available. Germ Cell Mutagenicity: No data available to indicate product or any components present at greater than 0.1% are mutagenic or genotoxic. Carcinogenicity: This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA. Reproductive Toxicity: This product is not expected to cause reproductive or developmental effects. Specific Target Organ Toxicity (Single Exposure): Respiratory tract irritation. Specific Target Organ Toxicity (Repeated Exposure): May cause damage to organs through prolonged or repeated exposure. Aspiration Hazard: May be fatal if swallowed and enters airways. Symptoms/Injuries After Inhalation: Prolonged inhalation may be harmful. May cause damage to organs by inhalation. May cause irritation to the respiratory system. Symptoms/Injuries After Skin Contact: Causes skin irritation. May cause an allergic skin reaction. 2-Butoxy ethanol may be absorbed through the skin in toxic amounts if contact is repeated and prolonged. These effects have not been observed in humans. Symptoms/Injuries After Eye Contact: Causes serious eye irritation. Symptoms/Injuries After Ingestion: May be fatal if swallowed and enters airways. Chronic Symptoms: Prolonged inhalation may be harmful. May be harmful if absorbed through skin. 2-Butoxy ethanol may be absorbed through the skin in toxic amounts if contact is repeated and prolonged. These effects have not been observed in humans. May cause damage to organs through prolonged or repeated exposure. SECTION 12: ECOLOGICAL INFORMATION 12.1. Toxicity Harmful to aquatic life with long lasting effects. Accumulation in aquatic organisms is expected. Product Species Test Results Freeze-OffÂ® Super Penetrant Crustacea EC50 Daphnia 22847.4102 mg/l, 48 hours estimated Fish LC50 Fish 1029.5527 mg/l, 96 hours estimated Components Species Test Results 2-Butoxyethanol (CAS 111-76-2) Aquatic Acute Crustacea EC50 Water flea (Daphnia magna) 1550 mg/l, 48 hours Fish LC50 Rainbow trout,donaldson trout >1000 mg/l, 96 hours (Oncorhynchus mykiss) 4-Hydroxy-4-methylpentan-2-one (Diacetone alcohol) (CAS 123-42-2) Aquatic Crustacea EC50 Water flea (Daphnia magna) 8750 mg/l, 48 hours Fish LC50 Bluegill (Lepomis macrochirus) 420 mg/l, 96 hours Goldfish (Carassius auratus) > 5000 mg/l, 24 hours 12.2. Persistence and Degradability No data is available on the degradability of this product. 12.3. Bioaccumulative Potential No data available. 12.4. Mobility in Soil No data available. 12.5. Other Adverse Effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component. SECTION 13: DISPOSAL CONSIDERATIONS 13.1. Waste treatment methods Waste Disposal Recommendations: This material and its container must be disposed of as hazardous waste. If discarded, this product is considered a RCRA ignitable waste, D001. Consult authorities before disposal. Contents under pressure. Do not puncture, incinerate or crush. Do not allow this material to drain into sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used container. Dispose of contents/container in accordance with local/regional/national regulations. Additional Information: Contaminated packaging Empty containers should be taken to an approved waste handling site for recycling or disposal. Since emptied containers may retain product residue, follow label warnings even after container is emptied. Do not re-use empty containers. SECTION 14: TRANSPORT INFORMATION 14.1 In Accordance with DOT Proper Shipping Name |Aerosols, flammable, limited quantity Hazard Class |2.1 |<PICTOGRAM PHRASE> Identification Number|UN1950 | Label Codes |2.1 | ERG Number | 14.2 In Accordance with IMDG Proper Shipping Name |AEROSOLS, LIMITED QUANTITY Hazard Class |2 Identification Number|UN1950 Label Codes | |<PICTOGRAM PHRASE> ntification Of The | | Substance/m | | EmS-No. (Fire) |F-D | EmS-No. (Spillage) |S-U | 14.3 In Accordance with IATA Proper Shipping Name |Aerosols, flammable, limited quantity Identification Number|UN1950 |<PICTOGRAM PHRASE> Hazard Class |2.1 | Label Codes | | ntification Of The | | Substance/m | | ERG Code (IATA) |10L SECTION 15: REGULATORY INFORMATION 15.1 US Federal Regulations <COMPONENT> This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200. SARA 304 Emergency release notification: Not regulated. US. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050): Not listed. US EPCRA (SARA Title III) Section 313 - Toxic Chemical: Listed substance: 2-Butoxyethanol (CAS 111-76-2) CERCLA Hazardous Substance List (40 CFR 302.4): 2-Butoxyethanol (CAS 111-76-2) CERCLA Hazardous Substances: Reportable quantity: Not listed. Spills or releases resulting in the loss of any ingredient at or above its RQ require immediate notification to the National Response Center (800-424-8802) and to your Local Emergency Planning Committee. Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List: Not regulated. Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130): 1,1-Difluoroethane (CAS 75-37-6) SARA Section 311/312 Hazard Classes |Immediate Hazard - Yes |Delayed Hazard - Yes |Fire Hazard - Yes |Pressure Hazard - Yes |Reactivity Hazard - No Toxic Substances Control Act (TSCA) |Not regulated. 15.2 US State Regulations <COMPONENT> US. New Jersey RTK - Substances: Listed substance 1,1-Difluoroethane (CAS 75-37-6) 2-Butoxyethanol (CAS 111-76-2) 4-Hydroxy-4-methylpentan-2-one (Diacetone alcohol) (CAS 123-42-2) Stoddard Solvent (CAS 8052-41-3) Turpentine, oil (CAS 8006-64-2) US. Massachusetts RTK - Substance List 1,1-Difluoroethane (CAS 75-37-6) 2-Butoxyethanol (CAS 111-76-2) 4-Hydroxy-4-methylpentan-2-one (Diacetone alcohol) (CAS 123-42-2) Stoddard Solvent (CAS 8052-41-3) Turpentine, oil (CAS 8006-64-2) US. Pennsylvania RTK - Hazardous Substances 2-Butoxyethanol (CAS 111-76-2) 4-Hydroxy-4-methylpentan-2-one (Diacetone alcohol) (CAS 123-42-2) Stoddard Solvent (CAS 8052-41-3) US. Rhode Island RTK 1,1-Difluoroethane (CAS 75-37-6) 2-Butoxyethanol (CAS 111-76-2) US. California Proposition 65 WARNING: This product contains a chemical known to the State of California to cause cancer. US - California Proposition 65 - CRT: Listed date/Carcinogenic substance Cumene (CAS 98-82-8) Listed: April 6, 2010 SECTION 16: OTHER INFORMATION, INCLUDING DATE OF PREPARATION OR LAST REVISION Revision date | Other |This document has been prepared in accordance with the SDS Information |requirements of the OSHA Hazard Communication Standard 29 CFR |1910.1200. GHS Full Text Phrases: ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | Grainger disclaimer.
The information contained in this SDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'SDS' shall be created or inferred by any statement in this 'SDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'SDS'. The user is responsible for full compliance.