Product Categories See All
Track Order Status
SDS Sheet 0066790Printer Friendly View
SECTION 1: IDENTIFICATION 1.1. Product Identifier Product Form: Aerosol. Product Name: Mass Air Flow Sensor Cleaner CAS No: Synonyms: 1.2. Intended Use of the Product Use of the substance/mixture: Mass air flow sensor cleaner 1.3. Name, Address, and Telephone of the Responsible Party Company: CRC Industries, Inc. 885 Louis Dr. Warminster, PA 18974 US Phone: 215-674-4300 1.4. Emergency Telephone Number Emergency |800-424-9300 (US) number |703-527-3887 (International) SECTION 2: HAZARDS IDENTIFICATION 2.1. Classification of the Substance or Mixture Classification (GHS-US) Flammable |Category 1 aerosols | Gases under |Compressed gas pressure | Reproductive |Category 2 toxicity | (fertility) | Specific |Category 2 target organ | toxicity, | repeated | exposure | Aspiration |Category 1 hazard | Hazardous to |Category 2 the aquatic | environment, | acute hazard | Hazardous to |Category 2 the aquatic | environment, | long-term | hazard | 2.2. Label Elements GHS-US Labeling Hazard Pictograms (GHS-US) |Flame |Gas Cylinder |Health Hazard Signal Word (GHS-US) |Danger Hazard Statements (GHS-US) |Extremely flammable aerosol. Contains gas under |pressure; may explode if heated. May be fatal if |swallowed and enters airways. Suspected of damaging |fertility. May cause damage to organs (eyes, |central nervous system, liver, kidney) through |prolonged or repeated exposure. Toxic to aquatic |life. Toxic to aquatic life with long lasting |effects. Precautionary Statements |Prevention: (GHS-US) |Obtain special instructions before use. Do not |handle until all safety precautions have been read |and understood. Keep away from heat/sparks/open |flames/hot surfaces. - No smoking. Do not spray on |an open flame or other ignition source. Do not apply |while equipment is energized. Pressurized |container: Do not pierce or burn, even after use. |Extinguish all flames, pilot lights and heaters. |Vapors will accumulate readily and may ignite. Use |only with adequate ventilation; maintain |ventilation during use and until all vapors are |gone. Open doors and windows or use other means to |ensure a fresh air supply during use and while |product is drying. If you experience any symptoms |listed on this label, increase ventilation or leave |the area. Do not breathe gas. Do not breathe mist |or vapor. Wear protective gloves/protective |clothing/eye protection/face protection. Avoid |release to the environment. | |Response: |If swallowed: Immediately call a poison |center/doctor. Do NOT induce vomiting. If exposed or |concerned: Get medical attention. Collect spillage. | |Storage: |Store in a well-ventilated place. Store locked up. |Protect from sunlight. Do not expose to |temperatures exceeding 50Â°C/122Â°F. Exposure to high |temperature may cause can to burst. | |Disposal: |Dispose of contents/container in accordance with |local/regional/national regulations. 2.3. Other Hazards Other Hazards Not Contributing to the Classification: Static accumulating flammable liquid can become electrostatically charged even in bonded and grounded equipment. Sparks may ignite liquid and vapor. May cause flash fire or explosion. 2.4. Unknown Acute Toxicity (GHS-US) SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS 3.1. Substance Name |Product identifier |% |Classification | | |(GHS-US) | | | | | | | | | | | | | | | Full text of H-phrases: See Section 16 3.2. Mixture Name |Product identifier |% |Classification | | |(GHS-US) Naphtha (petroleum), |64742-49-0 |80 - 90 | hydrotreated light | | | Carbon dioxide |124-38-9 |5 - 10 | 2,2,4-Trimethylpentane |540-84-1 |3 - 5 | n-Hexane |110-54-3 |3 - 5 | Methanol |67-56-1 |< 1 | Specific chemical identity and/or percentage of composition has been withheld as a trade secret. SECTION 4: FIRST AID MEASURES 4.1. Description of First Aid Measures First-aid Measures General: IF exposed or concerned: Get medical advice/attention. Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves. Show this safety data sheet to the doctor in attendance. First-aid Measures After Inhalation: If symptoms develop move victim to fresh air. Get medical attention if symptoms persist. First-aid Measures After Skin Contact: Rinse skin with water/shower. Get medical attention if irritation develops and persists. First-aid Measures After Eye Contact: Rinse with water. Get medical attention if irritation develops and persists. First-aid Measures After Ingestion: Call a physician or poison control center immediately. Do not induce vomiting. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs. Aspiration may cause pulmonary edema and pneumonitis. 4.2. Most important symptoms and effects, both acute and delayed Symptoms/Injuries: Prolonged exposure may cause chronic effects. Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: 4.3. Indication of Any Immediate Medical Attention and Special Treatment Needed Provide general supportive measures and treat symptomatically. Keep victim under observation. Symptoms may be delayed. SECTION 5: FIRE-FIGHTING MEASURES 5.1. Extinguishing Media Suitable Extinguishing Media: Water fog. Foam. Dry chemical powder, carbon dioxide, sand or earth may be used for small fires only. Unsuitable Extinguishing Media: Do not use water jet as an extinguisher, as this will spread the fire. 5.2. Special Hazards Arising From the Substance or Mixture Fire Hazard: Extremely flammable aerosol. Explosion Hazard: Contents under pressure. Pressurized container may explode when exposed to heat or flame. This product is a poor conductor of electricity and can become electrostatically charged. If sufficient charge is accumulated, ignition of flammable mixtures can occur. Static electricity accumulation may be significantly increased by the presence of small quantities of water or other contaminants. Material will float and may ignite on surface of water. Reactivity: 5.3. Advice for Firefighters Precautionary Measures Fire: Firefighting Instructions: In case of fire: Stop leak if safe to do so. Move containers from fire area if you can do so without risk. Containers should be cooled with water to prevent vapor pressure build up. Protection During Firefighting: Firefighters must use standard protective equipment including flame retardant coat, helmet with face shield, gloves, rubber boots, and in enclosed spaces, SCBA. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal Precautions, Protective Equipment and Emergency Procedures General Measures: Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of low areas. Remove all possible sources of ignition in the surrounding area. Wear appropriate protective equipment and clothing during clean-up. Do not breathe mist or vapor. Do not breathe gas. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Ventilate closed spaces before entering them. Use appropriate containment to avoid environmental contamination. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS. 6.1.1. For Non-emergency Personnel Protective Equipment: Emergency Procedures: 6.1.2. For Emergency Responders Protective Equipment: Emergency Procedures: 6.2. Environmental Precautions Avoid release to the environment. Contact local authorities in case of spillage to drain/aquatic environment. Prevent further leakage or spillage if safe to do so. Do not contaminate water. Avoid discharge into drains, water courses or onto the ground. Use appropriate containment to avoid environmental contamination. 6.3. Methods and Material for Containment and Cleaning Up For Containment: Methods for Cleaning Up: Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep combustibles (wood, paper, oil, etc.) away from spilled material. Stop the flow of material, if this is without risk. Collect spillage. Prevent entry into waterways, sewer, basements or confined areas. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination. For waste disposal, see section 13 of the SDS. 6.4. Reference to Other Sections See heading 8, Exposure Controls and Personal Protection. SECTION 7: HANDLING AND STORAGE 7.1. Precautions for Safe Handling Additional Hazards When Processed: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Minimize fire risks from flammable and combustible materials (including combustible dust and static accumulating liquids) or dangerous reactions with incompatible materials. Handling operations that can promote accumulation of static charges include but are not limited to: mixing, filtering, pumping at high flow rates, splash filling, creating mists or sprays, tank and container filling, tank cleaning, sampling, gauging, switch loading, vacuum truck operations. Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or expose containers to heat, flame, sparks, or other sources of ignition. Use caution around energized equipment. The metal container will conduct electricity if it contacts a live source. This may result in injury to the user from electrical shock and/or flash fire. Do not breathe mist or vapor. Do not breathe gas. Avoid prolonged exposure. Use only in well-ventilated areas. Should be handled in closed systems, if possible. Pregnant or breastfeeding women must not handle this product. Wear appropriate personal protective equipment. Wash hands thoroughly after handling. Observe good industrial hygiene practices. Avoid release to the environment. Do not empty into drains. For product usage instructions, please see the product label. Hygiene Measures: When using, do not eat, drink or smoke. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. 7.2. Conditions for Safe Storage, Including Any Incompatibilities Technical Measures: Storage Conditions: Level 3 Aerosol. Pressurized container. Protect from sunlight and do not expose to temperatures exceeding 50Â°C/122 Â°F. Do not puncture, incinerate or crush. Do not handle or store near an open flame, heat or other sources of ignition. This material can accumulate static charge which may cause spark and become an ignition source. Avoid spark promoters. These alone may be insufficient to remove static electricity. Store in a well-ventilated place. Store away from incompatible materials (see Section 10 of the SDS). 7.3. Specific End Use(s) SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1. Control Parameters US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) Components Type Value 2,2,4-Trimethylpentane PEL 2350 mg/m3 (CAS 540-84-1) 500 ppm Carbon dioxide (CAS PEL 9000 mg/m3 124-38-9) US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) Components Type Value Methanol (CAS 67-56-1) PEL 5000 ppm 260 mg/m3 200 ppm n-Hexane (CAS 110-54-3) PEL 1800 mg/m3 500 ppm US. ACGIH Threshold Limit Values Components Type Value Carbon dioxide (CAS 124-38-9) STEL 30000 ppm TWA 5000 ppm Methanol (CAS 67-56-1) STEL 250 ppm TWA 200 ppm n-Hexane (CAS 110-54-3) TWA 50 ppm US. NIOSH: Pocket Guide to Chemical Hazards Components Type Value 2,2,4-Trimethylpentane Ceiling 1800 mg/m3 (CAS 540-84-1) 385 ppm TWA 350 mg/m3 Carbon dioxide (CAS 124-38-9) STEL 54000 mg/m3 30000 ppm TWA 9000 mg/m3 5000 ppm Methanol (CAS 67-56-1) STEL 325 mg/m3 250 ppm TWA 260 mg/m3 200 ppm n-Hexane (CAS 110-54-3) TWA 180 mg/m3 50 ppm 8.2. Exposure Controls Appropriate Engineering |Good general ventilation (typically 10 air changes Controls |per hour) should be used. Ventilation rates should |be matched to conditions. If applicable, use process |enclosures, local exhaust ventilation, or other |engineering controls to maintain airborne levels |below recommended exposure limits. If exposure |limits have not been established, maintain airborne |levels to an acceptable level. Personal Protective Equipment| Materials for Protective | Clothing | Hand Protection |Wear protective gloves such as: Nitrile. Polyvinyl |chloride (PVC). VitonÂ®. Eye Protection |Wear safety glasses with side shields (or goggles). Skin and Body Protection |Wear appropriate chemical resistant clothing. Respiratory Protection |If engineering controls are not feasible or if |exposure exceeds the applicable exposure limits, use |a NIOSH-approved cartridge respirator with an |organic vapor cartridge. Use a self contained |breathing apparatus in confined spaces and for |emergencies. Air monitoring is needed to determine |actual employee exposure levels. Thermal Hazard Protection |Wear appropriate thermal protective clothing, when |necessary. SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1. Information on Basic Physical and Chemical Properties Physical State |Liquid. Appearance | Odor |Not available. Odor Threshold |Not available. pH |Not available. Relative Evaporation Rate |Very fast. (butylacetate=1) | Melting Point |Not available. Freezing Point |Not available. Boiling Point |123 Â°F (50.6 Â°C) estimated Flash Point |< 0 Â°F (< -17.8 Â°C) Tag Closed Cup Auto-ignition Temperature |489.2 Â°F (254 Â°C) estimated Decomposition Temperature |Not available. Flammability (solid, gas) |Not available. Vapor Pressure |3201.5 hPa estimated Relative Vapor Density at 20 Â°C |> 1 (air = 1) Relative Density |0.7 estimated Specific Gravity | Solubility |Not available. Partition coefficient: |Not available. n-octanol/water | Viscosity |Not available. Lower Flammable Limit |0.9 % estimated Upper Flammable Limit |36 % estimated 9.2. Other Information SECTION 10: STABILITY AND REACTIVITY 10.1 Reactivity The product is stable and non-reactive under normal conditions of use, storage and transport. 10.2 Chemical Stability Material is stable under normal conditions. 10.3 Possibility of Hazardous Reactions No dangerous reaction known under conditions of normal use. 10.4 Conditions to Avoid Heat, flames and sparks. Contact with incompatible materials. 10.5 Incompatible Materials Strong oxidizing agents. 10.6 Hazardous Decomposition Products Carbon oxides. SECTION 11: TOXICOLOGICAL INFORMATION 11.1. Information on Toxicological Effects Acute Toxicity: May be fatal if swallowed and enters airways. Product Species Test Results Mass Air Flow Sensor Cleaner Acute Dermal LD50 Rabbit 2037.8894 mg/kg estimated Inhalation LC50 Rat 1527.8224 mg/l, 4 Hours estimated LC50 Rat 68313.3516 mg/m3, 4 hours estimated Oral LD50 Human 6193.4844 mg/kg estimated Rat 16418.0957 mg/kg estimated LDL0 Human 37160.9063 mg/kg estimated * Estimates for product may be based on additional component data not shown. Skin Corrosion/Irritation:Prolonged skin contact may cause temporary irritation. Serious Eye Damage/Irritation: Direct contact with eyes may cause temporary irritation. Respiratory or Skin Sensitization: Respiratory sensitization: Not available. Skin sensitization: This product is not expected to cause skin sensitization. Germ Cell Mutagenicity: No data available to indicate product or any components present at greater than 0.1% are mutagenic or genotoxic. Carcinogenicity: This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA. Reproductive ToxicitySuspected of damaging fertility. Specific Target Organ Toxicity (Single Exposure): Not classified. Specific Target Organ Toxicity (Repeated Exposure): May cause damage to organs (eyes, central nervous system, liver, kidney) through prolonged or repeated exposure. Aspiration HazardMay be fatal if swallowed and enters airways. Symptoms/Injuries After Inhalation: Prolonged inhalation may be harmful. May cause damage to organs through prolonged or repeated exposure by inhalation. Symptoms/Injuries After Skin Contact: Prolonged skin contact may cause temporary irritation. Symptoms/Injuries After Eye Contact: Direct contact with eyes may cause temporary irritation. Symptoms/Injuries After Ingestion: May be fatal if swallowed and enters airways. Chronic Symptoms: Prolonged inhalation may be harmful. May cause damage to organs through prolonged or repeated exposure. SECTION 12: ECOLOGICAL INFORMATION 12.1. Toxicity Toxic to aquatic life with long lasting effects. Accumulation in aquatic organisms is expected. Product Species Test Results Mass Air Flow Sensor Cleaner Aquatic Fish LC50 Fish 1329.3086 mg/l, 96 hours estimated Components Species Test Results Methanol (CAS 67-56-1) Aquatic Fish LC50 Rainbow trout,donaldson trout 18000 - 20000 mg/l, 96 hours (Oncorhynchus mykiss) Acute Crustacea EC50 Water flea (Daphnia magna) > 10000 mg/l, 48 hours Fish LC50 Rainbow trout,donaldson trout (Oncorhynchus mykiss) 18000 - 20000 mg/l, 96 hours n-Hexane (CAS 110-54-3) Aquatic Fish LC50 Fathead minnow (Pimephales promelas) 2.101 - 2.981 mg/l, 96 hours * Estimates for product may be based on additional component data not shown. 12.2. Persistence and Degradability Not available. 12.3. Bioaccumulative Potential Not available. 12.4. Mobility in Soil Not available. 12.5. Other Adverse Effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component. SECTION 13: DISPOSAL CONSIDERATIONS 13.1. Waste treatment methods Waste Disposal Recommendations: If discarded, this product is considered a RCRA ignitable waste, D001. Consult authorities before disposal. Contents under pressure. Do not puncture, incinerate or crush. Do not allow this material to drain into sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used container. Dispose in accordance with all applicable regulations. Additional Information: Hazardous waste code D001: Waste Flammable material with a flash point <140 F SECTION 14: TRANSPORT INFORMATION 14.1 In Accordance with DOT Proper Shipping Name |Aerosols, flammable, Limited Quantity Hazard Class |2.1 |<PICTOGRAM PHRASE> Identification Number|UN1950 | Label Codes |2.1 | ERG Number | 14.2 In Accordance with IMDG Proper Shipping Name |AEROSOLS, LIMITED QUANTITY, MARINE POLLUTANT Hazard Class |2 Identification Number|UN1950 Label Codes | |<PICTOGRAM PHRASE> ntification Of The | | Substance/m | | EmS-No. (Fire) |D | EmS-No. (Spillage) |U | 14.3 In Accordance with IATA Proper Shipping Name |Aerosols, flammable, Limited Quantity Identification Number|UN1950 |<PICTOGRAM PHRASE> Hazard Class |2.1 | Label Codes | | ntification Of The | | Substance/m | | ERG Code (IATA) |10L SECTION 15: REGULATORY INFORMATION 15.1 US Federal Regulations <COMPONENT> US EPCRA (SARA Title III) Section 313 - Toxic Chemical: Listed substance Methanol (CAS 67-56-1) n-Hexane (CAS 110-54-3) CERCLA Hazardous Substance List (40 CFR 302.4) 2,2,4-Trimethylpentane (CAS 540-84-1) Methanol (CAS 67-56-1) n-Hexane (CAS 110-54-3) CERCLA Hazardous Substances: Reportable quantity 2,2,4-Trimethylpentane (CAS 540-84-1) 1000 LBS Methanol (CAS 67-56-1) 5000 LBS n-Hexane (CAS 110-54-3) 5000 LBS Spills or releases resulting in the loss of any ingredient at or above its RQ require immediate notification to the National Response Center (800-424-8802) and to your Local Emergency Planning Committee. Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List 2,2,4-Trimethylpentane (CAS 540-84-1) n-Hexane (CAS 110-54-3) Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130) Not regulated. SARA Section 311/312 Hazard Classes |Immediate Hazard - Yes |Delayed Hazard - Yes |Fire Hazard - Yes |Pressure Hazard - Yes |Reactivity Hazard - No Toxic Substances Control Act (TSCA) |Not regulated. 15.2 US State Regulations <COMPONENT> US. New Jersey Worker and Community Right-to-Know Act 2,2,4-Trimethylpentane (CAS 540-84-1) Carbon dioxide (CAS 124-38-9) Methanol (CAS 67-56-1) n-Hexane (CAS 110-54-3) US. Massachusetts RTK - Substance List 2,2,4-Trimethylpentane (CAS 540-84-1) Carbon dioxide (CAS 124-38-9) n-Hexane (CAS 110-54-3) US. Pennsylvania Worker and Community Right-to-Know Law Methanol (CAS 67-56-1) 2,2,4-Trimethylpentane (CAS 540-84-1) Carbon dioxide (CAS 124-38-9) n-Hexane (CAS 110-54-3) US. Rhode Island RTK 2,2,4-Trimethylpentane (CAS 540-84-1) Methanol (CAS 67-56-1) n-Hexane (CAS 110-54-3) US. California Proposition 65 WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm. US - California Proposition 65 - CRT: Listed date/Developmental toxin Methanol (CAS 67-56-1) Listed: March 16, 2012 SECTION 16: OTHER INFORMATION, INCLUDING DATE OF PREPARATION OR LAST REVISION Revision date | Other |This document has been prepared in accordance with the SDS Information |requirements of the OSHA Hazard Communication Standard 29 CFR |1910.1200. GHS Full Text Phrases: ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | Grainger disclaimer.
The information contained in this SDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'SDS' shall be created or inferred by any statement in this 'SDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'SDS'. The user is responsible for full compliance.