Product Categories See All
Track Order Status
SDS Sheet 0066290Printer Friendly View
Safety Data Sheet Date of Issue: |Revision Date: 8/12/2015 |Revision Number: Imperial Supplies Part Number: 0066290 SECTION 1: IDENTIFICATION 1.1. Product Identifier Product Form: Product Name: DynatexÂ® 49595 White Lithium Grease CAS No: Synonyms: 49595WH10 1.2. Intended Use of the Product Use of the substance/mixture: Refer to Technical Data 1.3. Name, Address, and Telephone of the Responsible Party Company Dynatex a division of Soudal Accumetric 350 Ring Road Elizabethtown, KY, 42701 USA Phone: (270) 769-3385 1.4. Emergency Telephone Number Emergency | (800) 424-9300 number | SECTION 2: HAZARDS IDENTIFICATION 2.1. Classification of the Substance or Mixture Classification (GHS-US) SENSITIZATION |Category 1 - SKIN | | | 2.2. Label Elements GHS-US Labeling Hazard Pictograms (GHS-US) |Exclamat| | | | | |ion Mark| | | | | Signal Word (GHS-US) |Warning Hazard Statements (GHS-US) |May cause an allergic skin reaction Precautionary Statements |Response: (GHS-US) |If on skin: Wash with plenty of soap and water. |If skin irritation or rash occurs: Get medical |advice/attention. |Read label before use. |Wash contaminated clothing before reuse. |Prevention: |Avoid breathing dust/fume/gas/mist/ vapors/spray. |Contaminated work clothing must not be allowed out |of the workplace. |Wear protective gloves. |Storage: |N/A |Disposal: |Dispose of contents/container in accordance with |local, state and federal |regulations. 2.3. Other Hazards Other Hazards Not Contributing to the Classification: None known. 2.4. Unknown Acute Toxicity (GHS-US) 0% SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS 3.1. Substance Name |Product identifier |% |Classification | | |(GHS-US) | | | | | | | | | | | | | | | Full text of H-phrases: See Section 16 3.2. Mixture Name |Product identifier |% |Classification | | |(GHS-US) calcium |57855-77-3 |0.1% - | bis(dinonylnaphthalenesulphonate| |1% | ) | | | Zinc Oxide |1314-13-2 |1% - 5% | | | | | | | | | | SECTION 4: FIRST AID MEASURES 4.1. Description of First Aid Measures First-aid Measures General: First-aid Measures After Inhalation: Move the exposed person to fresh air at once. For breathing difficulties oxygen may be necessary. Get medical attention if any discomfort continues. First-aid Measures After Skin Contact: Remove contaminated clothing. Wash skin thoroughly with soap and water. Get medical attention if any discomfort continues. First-aid Measures After Eye Contact: Rinse with water. Contact physician if discomfort continues. First-aid Measures After Ingestion: DO NOT INDUCE VOMITING! Get medical attention immediately! 4.2. Most important symptoms and effects, both acute and delayed Symptoms/Injuries: Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: 4.3. Indication of Any Immediate Medical Attention and Special Treatment Needed SECTION 5: FIRE-FIGHTING MEASURES 5.1. Extinguishing Media Suitable Extinguishing Media: Foam, carbon dioxide, dry chemicals, sand, dolomite, etc. Unsuitable Extinguishing Media: N/A 5.2. Special Hazards Arising From the Substance or Mixture Fire Hazard: Explosion Hazard: Volume and pressure increases strongly when heated. Risk of container explosion in fire. Explosion risk when heated. Aerosol cans may explode in case of fire. Reactivity: 5.3. Advice for Firefighters Precautionary Measures Fire: Firefighting Instructions: Acrid smoke/fumes. Oxides of carbon, phosphorus, sulfur. Protection During Firefighting: Use water to keep fire-exposed containers cool and disperse vapors. Water spray may be used to flush spills away from exposure and to dilute spills to non-flammable mixtures. Keep run-off out of sewers and water sources. Dike for water control. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal Precautions, Protective Equipment and Emergency Procedures General Measures: Minimize skin contact. Avoid breathing vapors. Wear an appropriate respirator if exposure exceeds recommended guidelines. Remove sources of ignition. 6.1.1. For Non-emergency Personnel Protective Equipment: Emergency Procedures: 6.1.2. For Emergency Responders Protective Equipment: Emergency Procedures: 6.2. Environmental Precautions Keep product out of sewers and watercourses by diking or impounding. Advise authorities if product has entered or may enter sewers, watercourses or extensive land areas. Assure conformity with applicable government regulations. 6.3. Methods and Material for Containment and Cleaning Up For Containment: Methods for Cleaning Up: Spill Clean-up: Procedures Carefully collect spilled material in closed containers and leave for disposal according to local regulations. Provide good ventilation. Use appropriate protective clothing. Rinse area with water. Do not let washing down water. Do not let washing down water contaminate ponds or waterways. 6.4. Reference to Other Sections See heading 8, Exposure Controls and Personal Protection. SECTION 7: HANDLING AND STORAGE 7.1. Precautions for Safe Handling Additional Hazards When Processed: Keep away from heat, sparks, and open flames. Ventilate well, avoid breathing vapors. Use approved respirator if air contamination is above accepted level. Avoid spilling, skin and eye contact. Eye wash and emergency shower must be available at the work place. Containers to be kept tightly. Hygiene Measures: Wash at the end of each work shift and before eating, smoking and using the toilet. 7.2. Conditions for Safe Storage, Including Any Incompatibilities Technical Measures: Storage Conditions: Keep away from heat, sparks and open flame. Store separated from oxidizing materials, acids. Storage Criteria: Chemical storage. 7.3. Specific End Use(s) SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1. Control Parameters Occupational Exposure Limits: Ingredient Name ACGIH TLV OSHA PEL STEL calcium bis(dinonylnaphthalenesulphonate) N/A N/A N/A Zinc Oxide 2 mg/m3 dust 5 mg/m3 dust 10 mg/m3 Exposure Limits: Lubricating oils, petroleum, base oils, highly refined OSHA TWA 5 mg/m3 (oil mist) ACGIH TWA 5 mg/m3 (oil mist) STEL 10 mg/m3 (oil mist) Antimony dialkyldithiocarbamate OSHA TWA 5 mg/m3 as Sb ACGIH TWA 5 mg/m3 as Sb 8.2. Exposure Controls Appropriate Engineering |Use engineering controls to reduce air contamination Controls |to permissible exposure level. Personal Protective Equipment|N/A Materials for Protective | Clothing | Hand Protection |Protective Gloves: Chemical resistant gloves |required for prolonged or repeated contact. Eye Protection |Wear splash-proof eye goggles to prevent any |possibility of eye contact. Skin and Body Protection |Protective Clothing: Wear appropriate clothing to |prevent repeated or prolonged skin contact. Respiratory Protection |No specific recommendation made, but respiratory |protection may still be required under exceptional |circumstances when excessive air contamination |exists. Thermal Hazard Protection | SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1. Information on Basic Physical and Chemical Properties Physical State |Grease Appearance | Odor |Mild petroleum oil Odor Threshold |N/A pH |Not available Relative Evaporation Rate |Not available (butylacetate=1) | Melting Point |Not available Freezing Point | Boiling Point |Not available Flash Point |Not available Auto-ignition Temperature |N/A Decomposition Temperature |N/A Flammability (solid, gas) |N/A Vapor Pressure |Not available Relative Vapor Density at 20 Â°C | Relative Density | Specific Gravity |0.9 Solubility | Partition coefficient: |N/A n-octanol/water | Viscosity |Not available Lower Flammable Limit |N/A Upper Flammable Limit |N/A 9.2. Other Information VOC%: N/A Density lbs/Gal: N/A SECTION 10: STABILITY AND REACTIVITY 10.1 Reactivity 10.2 Chemical Stability Stable. 10.3 Possibility of Hazardous Reactions 10.4 Conditions to Avoid Avoid contact with acids and oxidizing substances. 10.5 Incompatible Materials 10.6 Hazardous Decomposition Products Oxides of carbon, phophorus, sulfur. SECTION 11: TOXICOLOGICAL INFORMATION 11.1. Information on Toxicological Effects Acute Toxicity: Toxicological Information: No experimental toxicological data on the preparation as such is available. Component Toxicological Information: Lubricating oils, petroleum, base oils, highly refined Carcinogenicity. IP 346 <3% LD50 >5,000 mg/kg (oral rat) LD50 skin >2,000 mg/kg (skin rbt) LC50 N/A Skin Corrosion/Irritation: Serious Eye Damage/Irritation: Respiratory or Skin Sensitization: Germ Cell Mutagenicity: Carcinogenicity: Reproductive Toxicity: Specific Target Organ Toxicity (Single Exposure): Specific Target Organ Toxicity (Repeated Exposure): Aspiration Hazard: Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: SECTION 12: ECOLOGICAL INFORMATION 12.1. Toxicity 12.2. Persistence and Degradability 12.3. Bioaccumulative Potential 12.4. Mobility in Soil 12.5. Other Adverse Effects Fate and Effects in Waste Water Treatment Plants: Complete information is not yet available. Environmental Effects: Complete information is not yet available. Environmental Fate and Distribution: Complete information is not yet available. SECTION 13: DISPOSAL CONSIDERATIONS 13.1. Waste treatment methods Waste Disposal Recommendations: We make no guarantee or warranty of any kind that the use or disposal of this product complies with all local, state, or federal laws. It is also the obligation of each user of the product mentioned herein to determine and comply with the requirements of all applicable statutes. Additional Information: SECTION 14: TRANSPORT INFORMATION 14.1 In Accordance with DOT Proper Shipping Name |N/A Hazard Class | |<PICTOGRAM PHRASE> Identification Number|N/A | Label Codes | | ERG Number | 14.2 In Accordance with IMDG Proper Shipping Name |Not subject to IMDG code. Hazard Class | Identification Number| Label Codes | |<PICTOGRAM PHRASE> ntification Of The | | Substance/m | | EmS-No. (Fire) | | EmS-No. (Spillage) | | 14.3 In Accordance with IATA Proper Shipping Name |Not subject to IATA regulations. Identification Number| |<PICTOGRAM PHRASE> Hazard Class | | Label Codes | | ntification Of The | | Substance/m | | ERG Code (IATA) | SECTION 15: REGULATORY INFORMATION 15.1 US Federal Regulations <COMPONENT> The contents of this MSDS comply with the OSHA Hazard Communication Standard 29 CFR 1910.1200. Lubricating oils, petroleum, base oils, highly refined SARA 302 No CERCLA No SARA 313 No Lithium complex thickener SARA 302 No CERCLA No SARA 313 No Phosphorodithioic acid, O,O-DI-C1-14-alkyl esters, zinc salts SARA 302 No CERCLA *** SARA 313 N982 - Zn Antimony dialkydithiocarbamate SARA 302 No CERCLA *** SARA 313 N010 - Ab *** Indicates that no RQ is assigned to this generic or broad class, although the class is a CERCLA hazardous substance. See Federal Register 13456 )April 4, 1985). Values in Section 313 column represent Category Codes for reporting under Section 313. SARA Section 311/312 Hazard Classes | Toxic Substances Control Act (TSCA) |All of the components of the product are |listed on the TSCA inventory or exempt. 15.2 US State Regulations <COMPONENT> California Proposition 65: This product DOES NOT contain chemicals considered by the State of California's Safe Drinking Water and Toxic Enforcement Act of 1986 as causing cancer or reproductive toxicity, and for which warnings are now required. Minnesota: Phosphorodithioic acid, O,O-DI-C1-14-alkyl esters, zinc salts Antimony dialkydithiocarbamate New Jersey: Lubricating oils, petroleum, base oils, highly refined Phosphorodithioic acid, O,O-DI-C1-14-alkyl esters, zinc salts Pennsylvania: Lubricating oils, petroleum, base oils, highly refined Phosphorodithioic acid, O,O-DI-C1-14-alkyl esters, zinc salts Antimony dialkydithiocarbamate Pennsylvania Rightto-Know: This product contains the following chemicals that the state of Pennsylvania has identified as Special Hazardous Substances (SHS), Environmental Hazards (EH), or both (ESHS). The PA regulations require that the MSDS identify all SHS or EH chemicals by chemical name, common name, and CAS Number if they comprise 0.01% or more. Zinc compounds regulated under CERCLA and SARA 313, Environmental Hazard Antimony compounds regulated under CERCLA and SARA 313, Environmental Hazard Composition Comments: The base oil for this product can be a mixture of any of the following highly refined petroleum streams: 64741-88-4; 64741-89-5; 64741-96-4; 64741-97-5; 64742-01-4; 64742-52-5; 64742-53-6; 64742-54-7; 64742-55-8; 64742-56-9; 64742-57-0; 64742-62-7; 64742-63-8; 64742-65-0; 72623-83-7; 72623-85-9; 72623-86-0; 72623-87-1 Carcinogenicity: The petroleum base oils contained in this product have been highly refined by a variety of processes including solvent extraction, solvent dewaxing and hydrotreating to remove aromatics and improve performance characteristics. None of the oils used are listed as a carcinogen by NTP, IARC, or OSHA. SECTION 16: OTHER INFORMATION, INCLUDING DATE OF PREPARATION OR LAST REVISION Revision date |8/12/2015 Other |This document has been prepared in accordance with the SDS Information |requirements of the OSHA Hazard Communication Standard 29 CFR |1910.1200. GHS Full Text Phrases: ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | Grainger disclaimer.
The information contained in this SDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'SDS' shall be created or inferred by any statement in this 'SDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'SDS'. The user is responsible for full compliance.