Product Categories See All
Track Order Status
SDS Sheet 0066180Printer Friendly View
SECTION 1: IDENTIFICATION | |1.1. Product Identifier Product Form: Product Name: 11 OZ SW S1 SILICONE SPRAY LB 12PK CAS No: Synonyms: 1.2. Intended Use of the Product Use of the substance/mixture: Lubricant 1.3. Name, Address, and Telephone of the Responsible Party Company Sprayway, Inc. 1005 S. Westgate Drive Addison, IL 60101 United States General Assistance 1-630-628-3000 1.4. Emergency Telephone Number Emergency | 1-866-836-8855, outside US 1-952-852-4646 number | SECTION 2: HAZARDS IDENTIFICATION 2.1. Classification of the Substance or Mixture Classification (GHS-US) Flammable |Category 1 aerosols | Aspiration |Category 1 hazard | 2.2. Label Elements GHS-US Labeling Hazard Pictograms (GHS-US) |Flame |Health Hazard Signal Word (GHS-US) |Danger Hazard Statements (GHS-US) |Extremely flammable aerosol. May be fatal if |swallowed and enters airways. Precautionary Statements |Prevention: Keep away from heat/sparks/open (GHS-US) |flames/hot surfaces. - No smoking. Do not spray on |an open flame or other ignition source. Pressurized |container: Do not pierce or burn, even after use. |Response: If swallowed: Immediately call a poison |center/doctor. Do NOT induce vomiting. |Storage: Store locked up. Protect from sunlight. Do |not expose to temperatures exceeding 50Â°C/122Â°F. |Disposal: Not available. 2.3. Other Hazards Other Hazards Not Contributing to the Classification: 2.4. Unknown Acute Toxicity (GHS-US) SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS 3.1. Substance Name |Product identifier |% |Classification | | |(GHS-US) | | | | | | | | | | | | | | | Full text of H-phrases: See Section 16 3.2. Mixture Name |Product identifier |% |Classification | | |(GHS-US) Butane |106-97-8 |40 - 60 | Propane |74-98-6 |20 - 40 | Odorless Mineral Spirits |64741-65-7 |10 - 20 | Other components below | |2.5 - 10| reportable levels | | | *Designates that a specific | | | chemical identity and/or | | | percentage of composition has | | | been withheld as a trade secret.| | | SECTION 4: FIRST AID MEASURES 4.1. Description of First Aid Measures First-aid Measures General: First-aid Measures After Inhalation: Move to fresh air. Call a physician if symptoms develop or persist. First-aid Measures After Skin Contact: Rinse skin with water/shower. First-aid Measures After Eye Contact: Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if present and easy to do. First-aid Measures After Ingestion: Call a physician or poison control center immediately. Do not induce vomiting. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs. 4.2. Most important symptoms and effects, both acute and delayed Symptoms/Injuries: Aspiration may cause pulmonary edema and pneumonitis. Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: 4.3. Indication of Any Immediate Medical Attention and Special Treatment Needed Provide general supportive measures and treat symptomatically. Keep victim under observation. Symptoms may be delayed. General information: Take off all contaminated clothing immediately. SECTION 5: FIRE-FIGHTING MEASURES 5.1. Extinguishing Media Suitable Extinguishing Media: Alcohol resistant foam. Water spray. Water fog. Dry chemical powder. Carbon dioxide (CO2). Unsuitable Extinguishing Media: Do not use water jet as an extinguisher, as this will spread the fire. 5.2. Special Hazards Arising From the Substance or Mixture Fire Hazard: Contents under pressure. Pressurized container may explode when exposed to heat or flame. General fire hazards: Extremely flammable aerosol. Explosion Hazard: Reactivity: 5.3. Advice for Firefighters Precautionary Measures Fire: Firefighting Instructions: Move containers from fire area if you can do so without risk. Containers should be cooled with water to prevent vapor pressure build up. For massive fire in cargo area, use unmanned hose holder or monitor nozzles, if possible. If not, withdraw and let fire burn out. Specific methods: Use standard firefighting procedures and consider the hazards of other involved materials. Move containers from fire area if you can do so without risk. Use water spray to cool unopened containers. In the event of fire and/or explosion do not breathe fumes. Protection During Firefighting: Firefighters must use standard protective equipment including flame retardant coat, helmet with face shield, gloves, rubber boots, and in enclosed spaces, SCBA. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal Precautions, Protective Equipment and Emergency Procedures General Measures: Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of low areas. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Wear appropriate protective equipment and clothing during clean-up. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Ventilate closed spaces before entering them. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS. 6.1.1. For Non-emergency Personnel Protective Equipment: Emergency Procedures: 6.1.2. For Emergency Responders Protective Equipment: Emergency Procedures: 6.2. Environmental Precautions Avoid discharge into drains, water courses or onto the ground. 6.3. Methods and Material for Containment and Cleaning Up For Containment: Methods for Cleaning Up: Refer to attached safety data sheets and/or instructions for use. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep combustibles (wood, paper, oil, etc.) away from spilled material. Stop leak if you can do so without risk. Move the cylinder to a safe and open area if the leak is irreparable. Use water spray to reduce vapors or divert vapor cloud drift. Isolate area until gas has dispersed. Prevent entry into waterways, sewer, basements or confined areas. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination. For waste disposal, see section 13 of the SDS. 6.4. Reference to Other Sections See heading 8, Exposure Controls and Personal Protection. SECTION 7: HANDLING AND STORAGE 7.1. Precautions for Safe Handling Additional Hazards When Processed: Do not handle or store near an open flame, heat or other sources of ignition. Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or expose containers to heat, flame, sparks, or other sources of ignition. All equipment used when handling the product must be grounded. Use non-sparking tools and explosion-proof equipment. Do not re-use empty containers. Avoid contact with skin and eyes. Avoid breathing dust/fume/gas/mist/vapors/spray. Use only in well-ventilated areas. Wear appropriate personal protective equipment. Wash hands thoroughly after handling. Observe good industrial hygiene practices. Hygiene Measures: Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. 7.2. Conditions for Safe Storage, Including Any Incompatibilities Technical Measures: Storage Conditions: Level 3 Aerosol. Store locked up. Pressurized container. Protect from sunlight and do not expose to temperatures exceeding 50Â°C/122 Â°F. Keep away from heat, sparks and open flame. Do not puncture, incinerate or crush. Do not handle or store near an open flame, heat or other sources of ignition. This material can accumulate static charge which may cause spark and become an ignition source. Store in a well-ventilated place. Refrigeration recommended. Store away from incompatible materials (see Section 10 of the SDS). 7.3. Specific End Use(s) SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1. Control Parameters Occupational exposure limits US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) Components Type Value Propane (CAS 74-98-6) PEL 1800 mg/m3 1000 ppm US. ACGIH Threshold Limit Values Components Type Value Butane (CAS 106-97-8) STEL 1000 ppm US. NIOSH: Pocket Guide to Chemical Hazards Components Type Value Butane (CAS 106-97-8) TWA 1900 mg/m3 800 ppm Propane (CAS 74-98-6) TWA 1800 mg/m3 1000 ppm 8.2. Exposure Controls Appropriate Engineering |Explosion-proof general and local exhaust Controls |ventilation. Personal Protective Equipment| Materials for Protective | Clothing | Hand Protection |Wear appropriate chemical resistant gloves. Eye Protection |Face shield is recommended. Wear safety glasses with |side shields (or goggles). Skin and Body Protection |Wear appropriate chemical resistant clothing. Respiratory Protection |If permissible levels are exceeded use NIOSH |mechanical filter / organic vapor cartridge or an |air-supplied respirator. Thermal Hazard Protection |Wear appropriate thermal protective clothing, when |necessary. SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1. Information on Basic Physical and Chemical Properties Physical State |Gas. Appearance |Clear. Odor |Solvent. Odor Threshold |Not available. pH |Not available. Relative Evaporation Rate |Not available. (butylacetate=1) | Melting Point |Not available. Freezing Point |Not available. Boiling Point |64.41 Â°F (18 Â°C) estimated Flash Point |-156.0 Â°F (-104.4 Â°C) Propellant estimated Auto-ignition Temperature |658 Â°F (347.78 Â°C) estimated Decomposition Temperature |Not available. Flammability (solid, gas) |Not available. Vapor Pressure |60 - 70 psig @70F estimated Relative Vapor Density at 20 Â°C |Not available. Relative Density |Not available. Specific Gravity |0.509 estimated Solubility |Not available. Partition coefficient: |Not available. n-octanol/water | Viscosity |Not available. Lower Flammable Limit |1 % estimated Upper Flammable Limit |7 % estimated 9.2. Other Information SECTION 10: STABILITY AND REACTIVITY 10.1 Reactivity The product is stable and non-reactive under normal conditions of use, storage and transport. 10.2 Chemical Stability Material is stable under normal conditions. 10.3 Possibility of Hazardous Reactions No dangerous reaction known under conditions of normal use. Hazardous polymerization does not occur. 10.4 Conditions to Avoid Avoid heat, sparks, open flames and other ignition sources. Avoid temperatures exceeding the flash point. Contact with incompatible materials. 10.5 Incompatible Materials Strong oxidizing agents. Nitrates. Fluorine. Chlorine. 10.6 Hazardous Decomposition Products No hazardous decomposition products are known. SECTION 11: TOXICOLOGICAL INFORMATION 11.1. Information on Toxicological Effects Acute Toxicity: May be fatal if swallowed and enters airways. Expected to be a low hazard for usual industrial or commercial handling by trained personnel. Exposure may cause temporary irritation, redness, or discomfort. If aspirated into lungs during swallowing or vomiting, may cause chemical pneumonia, pulmonary injury or death. Aspiration may cause pulmonary edema and pneumonitis. Skin Corrosion/Irritation: Prolonged skin contact may cause temporary irritation. Serious Eye Damage/Irritation: Direct contact with eyes may cause temporary irritation. Respiratory or Skin Sensitization: Not a respiratory sensitizer. Germ Cell Mutagenicity: No data available to indicate product or any components present at greater than 0.1% are mutagenic or genotoxic. Carcinogenicity: This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA. Reproductive Toxicity: This product is not expected to cause reproductive or developmental effects. Specific Target Organ Toxicity (Single Exposure): Not classified Specific Target Organ Toxicity (Repeated Exposure): Not classified. Aspiration Hazard: May be fatal if swallowed and enters airways. Symptoms/Injuries After Inhalation: Not available. Symptoms/Injuries After Skin Contact: No adverse effects due to skin contact are expected. Symptoms/Injuries After Eye Contact: Direct contact with eyes may cause temporary irritation. Symptoms/Injuries After Ingestion: Droplets of the product aspirated into the lungs through ingestion or vomiting may cause a serious chemical pneumonia. Smallest quantities reaching the lungs through swallowing or subsequent vomiting may result in lung edema or pneumonia. Chronic Symptoms: SECTION 12: ECOLOGICAL INFORMATION 12.1. Toxicity Contains a substance which causes risk of hazardous effects to the environment. Harmful to aquatic life with long lasting effects. Components Species Test Results Odorless Mineral Spirits (CAS 64741-65-7) Aquatic Algae IC50 Algae 30000 mg/L, 72 Hours * Estimates for product may be based on additional component data not shown. 12.2. Persistence and Degradability No data is available on the degradability of this product. 12.3. Bioaccumulative Potential No data available. 12.4. Mobility in Soil No data available. Partition coefficient n-octanol / water (log Kow) Butane 2.89 Propane 2.36 12.5. Other Adverse Effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component. SECTION 13: DISPOSAL CONSIDERATIONS 13.1. Waste treatment methods Waste Disposal Recommendations: Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Contents under pressure. Do not puncture, incinerate or crush. Dispose of contents/container in accordance with local/regional/national/international regulations. Additional Information: Local disposal regulations: Dispose in accordance with all applicable regulations. Hazardous waste code: The waste code should be assigned in discussion between the user, the producer and the waste disposal company. Waste from residues / unused products: Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see: Disposal instructions). Contaminated packaging: Empty containers should be taken to an approved waste handling site for recycling or disposal. Since emptied containers may retain product residue, follow label warnings even after container is emptied. Do not re-use empty containers. SECTION 14: TRANSPORT INFORMATION 14.1 In Accordance with DOT Proper Shipping Name |Aerosols, flammable Hazard Class |2.1 |<PICTOGRAM PHRASE> | | | |[pic] Identification Number|UN1950 | Label Codes |2.1 | ERG Number | 14.2 In Accordance with IMDG Proper Shipping Name |AEROSOLS Hazard Class |2.1 Identification Number|UN1950 Label Codes |2.1 |<PICTOGRAM PHRASE>[pic] ntification Of The | | Substance/m | | EmS-No. (Fire) |F-D | EmS-No. (Spillage) |S-U | 14.3 In Accordance with IATA Proper Shipping Name |Aerosols, flammable Identification Number|UN1950 |<PICTOGRAM PHRASE>[pic] Hazard Class |2.1 | Label Codes |2.1 | ntification Of The | | Substance/m | | ERG Code (IATA) |10L SECTION 15: REGULATORY INFORMATION 15.1 US Federal Regulations <COMPONENT> This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200. TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D): Not regulated. CERCLA Hazardous Substance List (40 CFR 302.4): Not listed. SARA 304 Emergency release notification: Not regulated. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050): Not listed. SARA 313 (TRI reporting): Not regulated. Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List: Not regulated. Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130) Butane (CAS 106-97-8) Propane (CAS 74-98-6) Safe Drinking Water Act (SDWA): Not regulated. SARA Section 311/312 Hazard Classes |Immediate Hazard - Yes |Delayed Hazard - No |Fire Hazard - Yes |Pressure Hazard - No |Reactivity Hazard - No Toxic Substances Control Act (TSCA) |All components are on the U.S. EPA TSCA |Inventory List. 15.2 US State Regulations <COMPONENT> US. Massachusetts RTK - Substance List Butane (CAS 106-97-8) Propane (CAS 74-98-6) US. New Jersey Worker and Community Right-to-Know Act Butane (CAS 106-97-8) Propane (CAS 74-98-6) US. Pennsylvania Worker and Community Right-to-Know Law Butane (CAS 106-97-8) Propane (CAS 74-98-6) US. Rhode Island RTK Butane (CAS 106-97-8) Propane (CAS 74-98-6) US. California Proposition 65: California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain any chemicals currently listed as carcinogens or reproductive toxins. SECTION 16: OTHER INFORMATION, INCLUDING DATE OF PREPARATION OR LAST REVISION Revision date |01-13-2015 Other |This document has been prepared in accordance with the SDS Information |requirements of the OSHA Hazard Communication Standard 29 CFR |1910.1200. GHS Full Text Phrases: ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | Grainger disclaimer.
The information contained in this SDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'SDS' shall be created or inferred by any statement in this 'SDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'SDS'. The user is responsible for full compliance.