Register Now    |    Login

National Distributor of Quality Maintenance Supplies Since 1958

1-800-558-2808

Track Order Status
Order No:
Zip Code:

MSDS Sheet 0066090

Printer Friendly View
        

MATERIAL SAFETY DATA SHEET

SECTION 1 PRODUCT AND COMPANY IDENTIFICATION

CHEVRON DELO® SYNTHETIC GREASE SF

Product Number(s): CPS235253
Company Identification
Chevron Products Company
A division of Chevron U.S.A. Inc.
6001 Bollinger Canyon Road
San Ramon, CA 94583
United States of America
www.chevronlubricants.com

Transportation Emergency Response
CHEMTREC: (800) 424-9300 or (703) 527-3887
Health Emergency
Chevron Emergency Information Center: Located in the USA. International collect
calls accepted. (800) 231-0623 or (510) 231-0623
Product Information
Email: lubemsds@Chevron.com
Product Information: (800) LUBE TEK
MSDS Request: (800) 414-6737

SECTION 2 COMPOSITION / INFORMATION ON INGREDIENTS

COMPONENTS                   CAS NUMBER          AMOUNT
Synthetic hydrocarbons       Mixture             80 - 90 % weight

SECTION 3 HAZARDS IDENTIFICATION

IMMEDIATE HEALTH EFFECTS
Eye: Not expected to cause prolonged or significant eye irritation.
Skin: Contact with the skin is not expected to cause prolonged or significant
irritation.
Contact with the skin is not expected to cause an allergic skin response.  Not
expected to be harmful to internal organs if absorbed through the skin.
High-Pressure Equipment Information:
Accidental high-velocity injection under the skin of materials of this type may
result in serious injury.  Seek medical attention at once should an accident
like this occur. The initial wound at the injection site may not appear to be
serious at first:  but, if left untreated, could result in disfigurement or
amputation of the affected part.

Ingestion: Not expected to be harmful if swallowed.
Inhalation: Not expected to be harmful if inhaled. Contains a synthetic
hydrocarbon oil. May cause respiratory irritation or other pulmonary effects
following prolonged or repeated inhalation of oil mist at airborne levels above
the recommended mineral oil mist exposure limit.
Symptoms of respiratory irritation ma include coughing and difficulty
breathing.

SECTION 4 FIRST AID MEASURES

Eye: No specific first aid measures are required. As a precaution, remove
contact lenses, if worn, and flush eyes with water.
Skin: No specific first aid measures are required. As a precaution, remove
clothing and shoes if contaminated. To remove the material from skin, apply a
waterless hand cleaner, mineral oil, or petroleum jelly. Then wash with soap
and water. Discard contaminated clothing and shoes or
thoroughly clean before reuse.
Ingestion: No specific first aid measures are required. Do not induce vomiting.
As a precaution, get medical advice.
Inhalation: No specific first aid measures are required. If exposed to
excessive levels of material in the air, move the exposed person to fresh air.
Get medical attention if coughing or respiratory discomfort occurs.
Note to Physicians: In an accident involving high-pressure equipment, this
product may be injected under the skin. Such an accident may result in a small,
sometimes bloodless, puncture wound. However, because of its driving force,
material injected into a fingertip can be deposited into the palm of the hand.
Within 24 hours, there is usually a great deal of swelling,
discoloration, and intense throbbing pain. Immediate treatment at a surgical
emergency center is recommended.

SECTION 5 FIRE FIGHTING MEASURES

FIRE CLASSIFICATION:
OSHA Classification (29 CFR 1910.1200): Not classified by OSHA as flammable or
combustible.

NFPA RATINGS:  Health: 0   Flammability: 1    Reactivity: 0

FLAMMABLE PROPERTIES:
Flashpoint: (Cleveland Open Cup) 200 degrees C  (392 degrees F) ( Min)
Auto ignition: No Data Available
Flammable (Explosive) Limits (%by volume in air): 
Lower: Not Applicable Upper: Not Applicable

EXTINGUISHING MEDIA: Use water fog, foam, dry chemical or carbon dioxide(CO2)
to extinguish flames.
PROTECTION OF FIRE FIGHTERS:
Fire Fighting Instructions: This material will burn although it is not easily
ignited. For fires involving this material, do not enter any enclosed or
confined fire space without proper protective equipment, including
self-contained breathing apparatus.
Combustion Products: Highly dependent on combustion conditions. A complex
mixture of airborne solids, liquids, and gases including carbon monoxide, carbon
dioxide, and unidentified organic compounds will be evolved when this material
undergoes combustion.

SECTION 6 ACCIDENTAL RELEASE MEASURES

Protective Measures: Eliminate all sources of ignition in vicinity of  spilled
material.
Spill Management: Clean up spills immediately, observing precautions in
Exposure Controls/Personal Protection section. Stop the source of the release 
if you can do it without risk.
Contain release to prevent further contamination of soil, surface water or
groundwater.
Clean up spill as soon as possible, observing precautions in Exposure
Controls/Personal Protection section. Stop the source of the release if you can
do it without risk. Contain release to prevent further contamination of soil,
surface water or groundwater. Clean up spill as soon as possible, observing
precautions in Exposure Controls/Personal Protection. Use appropriate
techniques such as applying non-combustible absorbent materials or pumping.
Where feasible and appropriate, remove contaminated soil. Place contaminated
materials in disposable containers and dispose of in a manner consistent with
applicable regulations.
Reporting: Report spills to local authorities and/or U.S. Coast Guard's
National Response Center at (800)424-8802 as appropriate or required.

SECTION 7 HANDLING AND STORAGE

Precautionary Measures: Keep out of the reach of children.
General Handling Information: Avoid contaminating soil or releasing this
material into sewage and drainage systems and bodies of water.
Static Hazard: Electrostatic charge may accumulate and create a hazardous
condition when handling this material. To  minimize this hazard, bonding and
grounding may be necessary but may not, by themselves, be sufficient. Review all
operations which have the potential of generating and accumulating an
electrostatic charge and/or a flammable atmosphere (including
tank and container filling, splash filling, tank cleaning, sampling, gauging,
switch loading, filtering, mixing, agitation, and vacuum truck operations) and
use appropriate mitigating procedures. For more information, refer to
OSHA Standard 29 CFR 1910.106, 'Flammable and Combustible  Liquids', National
Fire Protection Association (NFPA 77, 'Recommended Practice on Static
Electricity', and/or the American Petroleum Institute (AP) Recommended Practice
2003, 'Protection Against Ignitions Arising Out of Static, Lighting,
and Stray Currents'.
Container Warnings: Container is not designed to contain pressure. Do not use
pressure to empty container or it may rupture with explosive force. Empty
containers retain product residue (solid, liquid, and/or vapor) and can be
dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose
such containers to heat, flame, sparks, static electricity, or other sources of
ignition.
They may explode and cause injury or death. Empty containers should be
completely drained, properly closed, and promptly returned to a drum
reconditioner or disposed of properly.

SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION

GENERAL CONSIDERATIONS:
Consider the potential hazards of this material (see Section 3), applicable
exposure limits, job activities, and other substances in the work place when
designing engineering controls and selecting personal protective equipment. If
engineering controls or work practices are not adequate to prevent exposure to
harmful levels of this material, the personal protective equipment listed below
is recommended.
The user should read and understand all instructions and limitations supplied
with the equipment since protection is usually provided for a limited time or
under certain circumstances.

ENGINEERING CONTROLS:
Use in a well-ventilated area.

PERSONAL PROTECTIVE EQUIPMENT
Eye/Face protection: No special eye protection is normally required. Where
splashing is possible, wear safety glasses with side shields as a good safety
practice.
Skin Protection: No special protective clothing is normally required. Where
splashing  is possible, select protective clothing depending on operations
conducted, physical requirements and other substances in the workplace.
Suggested materials for protective gloves include: Neoprene,
Nitrile Rubber, Silver Shield, Viton.
Respiratory Protection: No respiratory protection is normally required.
If user operations generate an oil mist, determine if airborne concentrations
are below the occupational exposure limit for mineral oil mist. If not, wear an
approved respirator that provides adequate protection from the measured
concentrations of this material. For air-purifying respirators use a
particulate cartridge. Use a positive pressure air-supplying respirator in
circumstances where air-purifying respirators may not provide adequate
protection.

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES

Attention: The data below are typical values and do not constitute a
specification.

Color: Yellow
Physical State: Semi-solid
Odor: Petroleum odor
pH;  Not Applicable
Vapor Pressure: <0.01 mmHg @ 37.8 degrees C  (100 degrees F)
Vapor Density  (Air = 1): >1
Boiling Point:  No Data Available
Solubility: Soluble in hydrocarbons: insoluble in water
Melting Point: No Data Available
Viscosity: 105 cSt @ 40 degrees C ( 40 degrees F )  (Min)

SECTION 10 STABILITY AND REACTIVITY

Chemical Stability: This material is considered stable under normal ambient and
anticipated storage and handling conditions of temperature and pressure.
Incompatibility With Other Materials: May react with strong acids or strong
oxidizing agents, such as chlorates, nitrates, peroxides, et.
Hazardous Decomposition Products: None known (None expected)
Hazardous Polymerization: Hazardous polymerization will not occur.

SECTION 11 TOXICOLOGICAL INFORMATION

IMMEDIATE HEALTH EFFECTS
Eye irritation; The eye irritation hazard is based on evaluation of data for
similar materials or product components.
Skin Irritation: The skin irritation hazard is based on evaluation of data for
similar materials or product components.
Skin Sensitization: The skin sensitization hazard is based on evaluation of
data for similar materials or product components.
Acute Dermal Toxicity: The acute dermal toxicity hazard is based on evaluation
of data for similar materials or product components.
Acute Oral Toxicity: The acute oral toxicity hazard is based on evaluation of
data for similar materials or product components.
Acute Inhalation Toxicity: The acute inhalation toxicity hazard is based on
evaluation of data for similar materials or product components.

SECTION 12 ECOLOGICAL INFORMATION

ECOTOXICITY
The toxicity of this material to aquatic organisms has not been evaluated.
Consequently, this material should be kept out of sewage and drainage systems
and all bodies of water.

ENVIRONMENTAL FATE
This material is not expected to be readily biodegradable.

SECTION 13 DISPOSAL CONSIDERATIONS

Use material for its intended purpose or recycle if possible. Oil collection
services are available for used oil recycling or disposal. Place contaminated
materials in containers and dispose of in a manner consistent with applicable
regulations. Contact your sales representative or local environmental or health
authorities for approved disposal or recycling methods.


SECTION 14  TRANSPORT INFORMATION

The description shown may not apply to all shipping situations. Consult 49 CFR,
or appropriate Dangerous Goods Regulations, for additional description
requirements (e.g. technical name) and mode-specific or quantity-specific
shipping requirements.
DOT Shipping Description: PETROLEUM GREASE, N.E.C. NOT REGULATED AS A HAZARDOUS
MATERIAL FOR TRANSPORTATION UNDER 49 CFR

IMO/IMDG Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR
TRANSPORTATION UNDER THE IMDG CODE

ICAO/IATA Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR
TRANSPORTATION UNDER ICAO

SECTION 15 REGULATORY INFORMATION

EPCRA 311/312 CATEGORIES: 1. Immediate (Acute) Health Effects: NO
2. Delayed (Chronic) Health Effects: NO
3. Fire Hazard: NO
4. Sudden Release of Pressure Hazard: NO
5. Reactivity Hazard: NO

REGULATORY LISTS SEARCHED:
01-1=IARC Group 1            03=EPCRA 313
02-2A=IARC Group 2A          04=CA Proposition 65
01-2B=IARC Group 2B          05=MA RTK
02=NTP Carcinogen            06=NJ RTK
                             07=PA RTK
No components of this material were found on the regulatory lists above.
ZN NAPHTHENATE          03, 06

CHEMICAL INVENTORIES:
All components comply with the following chemical inventory requirements:
DSL (Canada), KECI (Korea), PICCS (Philippines), TSCA (United States).

One or more components does not comply with the following chemical inventory
requirements:  AICS (Australia).

NEW JERSEY RTK CLASSIFICATION:
Under the New Jersey Right-to-Know Act L. 1983 Chapter 315 N.J.S.A. 34:5A-1 et.
seq, the product is to be identified as follows: (Grease)

WHMIS CLASSIFICATION:
This product is not considered a controlled product according to the criteria
of the Canadian Controlled Products Regulations.

SECTION 16 OTHER INFORMATION

NFPA RATINGS:  Health: 0     Flammability: 1     Reactivity: 0

HMIS RATINGS:  Health: 1     Flammability: 1     Reactivity: 0
(0-Least, 1-Slight, 2-Modeate, 3-High, 4-Extreme, PPE: - Personal Protection
Equipment Index recommendation, 
*-Chronic Effects Indicator). These values are obtained using
the guidelines or published evaluations prepared by the National Fire Protection
Association (NFPA) or the National Paint and Coating Association (for HMIS
ratings).

LABEL RECOMMENDATION:
Label Category: GREASE 1 - GRS1

REVISION STATEMENT: This revision updates the following sections of this
Material Safety Data Sheet: 15
Revision Date: August 01, 2006

ABBREVIATIONS THAT MAY HAVE BEEN USED IN THIS DOCUMENT:
TLV - Threshold Limit Value       TWA - Time Weighted Average
STEL - Short-term Exposure Limit  PEL - Permissible Exposure Limit
CAS - Chemical Abstract Service Number
ACGIH - American Conference of Government Industrial Hygienists
IMO/IMDG - International Maritime Dangerous Goods Code
API - American Petroleum Institute      MSDS - Material Safety Data Sheet
CVX - Chevron           NFPA - National Fire Protection Association (USA)
DOT - Department of Transportation (USA)
NTP - National Toxicology Program (USA)
IARC - International Agency for Research on Cancer
OSHA - Occupational Safety and Health Administration

Prepared according to the OSHA Hazard Communication Standard (29 CFR 1910.1200)
and the ANSI MSDS Standard (Z400.1) by the Chevron Energy Technology Company,
100 Chevron Way, Richmond, California 94802.

The above information is based on the data of which we are aware and is
believed to be correct as of the date hereof.  Since this information may be
applied under conditions beyond our control and with which we may be unfamiliar
and since data made available subsequent to the date hereof may suggest
modifications of the information, we do not assume any responsibility for the
results of its use.  This information is furnished upon condition that the
person receiving it shall make his own determination of the suitability of the
material for his particular purpose.

    

The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'MSDS' shall be created or inferred by any statement in this 'MSDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'MSDS'. The user is responsible for full compliance.

Feedback