Product Categories See All
Track Order Status
SDS Sheet 0066010Printer Friendly View
Safety Data Sheet Date of Issue: |Revision Date: OCTOBER 20, |Revision Number: 9 |2014 | Imperial Supplies Part Number: 0066010 SECTION 1: IDENTIFICATION 1.1. Product Identifier Product Form: Product Name: Chevron Ultra-Duty Grease EP NLGI 0, 1, 2 CAS No: Synonyms: 1.2. Intended Use of the Product Use of the substance/mixture: Grease. 1.3. Name, Address, and Telephone of the Responsible Party Company Chevron Products Company a division of Chevron U.S.A. Inc. 6001 Bollinger Canyon Rd. San Ramon, CA 94583 United States of America Phone: 1 (800) 582-3835 1.4. Emergency Telephone Number Emergency |CHEMTREC: (800) 424-9300 or (703) 527-3887, Chevron Emergency number |Information Center: Located in the USA. International collect calls |accepted. (800) 231-0623 or (510) 231-0623 SECTION 2: HAZARDS IDENTIFICATION 2.1. Classification of the Substance or Mixture Classification (GHS-US) Acute aquatic |Category 3 toxicant | Chronic |Category 3 aquatic | toxicant | | 2.2. Label Elements GHS-US Labeling Hazard Pictograms (GHS-US) | | | | | | Signal Word (GHS-US) | Hazard Statements (GHS-US) |Harmful to aquatic life with long lasting effects. Precautionary Statements |Prevention: (GHS-US) |Avoid release to the environment. |Disposal: |Dispose of contents/container in accordance with |applicable local/regional/national/international |regulations. 2.3. Other Hazards Other Hazards Not Contributing to the Classification: Not Applicable. 2.4. Unknown Acute Toxicity (GHS-US) SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS 3.1. Substance Name |Product identifier |% |Classification | | |(GHS-US) | | | | | | | | | | | | | | | Full text of H-phrases: See Section 16 3.2. Mixture Name |Product identifier |% |Classification | | |(GHS-US) Highly refined mineral oil (C15 |Mixture |70 - 99 | - C50) | |%wt/wt | Zinc dialkyldithiophosphate |68649-42-3 |1 - 5 | | |%wt/wt | | | | | | | | | | SECTION 4: FIRST AID MEASURES 4.1. Description of First Aid Measures First-aid Measures General: First-aid Measures After Inhalation: No specific first aid measures are required. If exposed to excessive levels of material in the air, move the exposed person to fresh air. Get medical attention if coughing or respiratory discomfort occurs. First-aid Measures After Skin Contact: No specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated. To remove the material from skin, apply a waterless hand cleaner, mineral oil, or petroleum jelly. Then wash with soap and water. Discard contaminated clothing and shoes or thoroughly clean before reuse. First-aid Measures After Eye Contact: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water. First-aid Measures After Ingestion: No specific first aid measures are required. Do not induce vomiting. As a precaution, get medical advice. 4.2. Most important symptoms and effects, both acute and delayed Symptoms/Injuries: Symptoms/Injuries After Inhalation: Not expected to be harmful if inhaled. Contains a petroleum-based mineral oil. May cause respiratory irritation or other pulmonary effects following prolonged or repeated inhalation of oil mist at airborne levels above the recommended mineral oil mist exposure limit. Symptoms of respiratory irritation may include coughing and difficulty breathing. Symptoms/Injuries After Skin Contact: Contact with the skin is not expected to cause prolonged or significant irritation. Contact with the skin is not expected to cause an allergic skin response. Not expected to be harmful to internal organs if absorbed through the skin. High-Pressure Equipment Information: Accidental high-velocity injection under the skin of materials of this type may result in serious injury. Seek medical attention at once should an accident like this occur. The initial wound at the injection site may not appear to be serious at first; but, if left untreated, could result in disfigurement or amputation of the affected part. Symptoms/Injuries After Eye Contact: Not expected to cause prolonged or significant eye irritation. Symptoms/Injuries After Ingestion: Not expected to be harmful if swallowed. Chronic Symptoms: Not classified. 4.3. Indication of Any Immediate Medical Attention and Special Treatment Needed Note to Physicians: In an accident involving high-pressure equipment, this product may be injected under the skin. Such an accident may result in a small, sometimes bloodless, puncture wound. However, because of its driving force, material injected into a fingertip can be deposited into the palm of the hand. Within 24 hours, there is usually a great deal of swelling, discoloration, and intense throbbing pain. Immediate treatment at a surgical emergency center is recommended. SECTION 5: FIRE-FIGHTING MEASURES 5.1. Extinguishing Media Suitable Extinguishing Media: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames. Unsuitable Extinguishing Media: 5.2. Special Hazards Arising From the Substance or Mixture Fire Hazard: Explosion Hazard: Reactivity: 5.3. Advice for Firefighters Precautionary Measures Fire: Firefighting Instructions: This material will burn although it is not easily ignited. See Section 7 for proper handling and storage. For fires involving this material, do not enter any enclosed or confined fire space without proper protective equipment, including self-contained breathing apparatus. Protection During Firefighting: SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal Precautions, Protective Equipment and Emergency Procedures General Measures: Eliminate all sources of ignition in vicinity of spilled material. 6.1.1. For Non-emergency Personnel Protective Equipment: Emergency Procedures: 6.1.2. For Emergency Responders Protective Equipment: Emergency Procedures: 6.2. Environmental Precautions 6.3. Methods and Material for Containment and Cleaning Up For Containment: Methods for Cleaning Up: Spill Management: Clean up spills immediately, observing precautions in Exposure Controls/Personal Protection section. Stop the source of the release if you can do it without risk. Contain release to prevent further contamination of soil, surface water or groundwater. Clean up spill as soon as possible, observing precautions in Exposure Controls/Personal Protection. Use appropriate techniques such as applying non-combustible absorbent materials or pumping. Where feasible and appropriate, remove contaminated soil. Place contaminated materials in disposable containers and dispose of in a manner consistent with applicable regulations. Reporting: Report spills to local authorities as appropriate or required. 6.4. Reference to Other Sections See heading 8, Exposure Controls and Personal Protection. SECTION 7: HANDLING AND STORAGE 7.1. Precautions for Safe Handling Additional Hazards When Processed: Avoid contaminating soil or releasing this material into sewage and drainage systems and bodies of water. Static Hazard: Electrostatic charge may accumulate and create a hazardous condition when handling this material. To minimize this hazard, bonding and grounding may be necessary but may not, by themselves, be sufficient. Review all operations which have the potential of generating and accumulating an electrostatic charge and/or a flammable atmosphere (including tank and container filling, splash filling, tank cleaning, sampling, gauging, switch loading, filtering, mixing, agitation, and vacuum truck operations) and use appropriate mitigating procedures. For more information, refer to OSHA Standard 29 CFR 1910.106, 'Flammable and Combustible Liquids', National Fire Protection Association (NFPA 77, 'Recommended Practice on Static Electricity', and/or the American Petroleum Institute (API) Recommended Practice 2003, 'Protection Against Ignitions Arising Out of Static, Lightning, and Stray Currents'. Hygiene Measures: Do not get in eyes, on skin, or on clothing. Keep out of the reach of children. Wash thoroughly after handling. 7.2. Conditions for Safe Storage, Including Any Incompatibilities Technical Measures: Container Warnings: Container is not designed to contain pressure. Do not use pressure to empty container or it may rupture with explosive force. Empty containers retain product residue (solid, liquid, and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, static electricity, or other sources of ignition. They may explode and cause injury or death. Empty containers should be completely drained, properly closed, and promptly returned to a drum reconditioner or disposed of properly. Storage Conditions: 7.3. Specific End Use(s) SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1. Control Parameters GENERAL CONSIDERATIONS: Consider the potential hazards of this material (see Section 3), applicable exposure limits, job activities, and other substances in the work place when designing engineering controls and selecting personal protective equipment. If engineering controls or work practices are not adequate to prevent exposure to harmful levels of this material, the personal protective equipment listed below is recommended. The user should read and understand all instructions and limitations supplied with the equipment since protection is usually provided for a limited time or under certain circumstances. Occupational Exposure Limits: Component Agency TWA STEL Ceiling Notation Highly refined mineral oil (C15 - C50) ACGIH 5 mg/m3 10 mg/m3 -- -- Highly refined mineral oil (C15 - C50) OSHA Z-1 5 mg/m3 -- -- -- Zinc dialkyldithiophosphate Not Applicable -- -- -- -- Consult local authorities for appropriate values. 8.2. Exposure Controls Appropriate Engineering |Use in a well-ventilated area. Controls | Personal Protective Equipment| Materials for Protective | Clothing | Hand Protection | Eye Protection |No special eye protection is normally required. |Where splashing is possible, wear safety glasses |with side shields as a good safety practice. Skin and Body Protection |No special protective clothing is normally required. |Where splashing is possible, select protective |clothing depending on operations conducted, physical |requirements and other substances in the workplace. |Suggested materials for protective gloves include: |Neoprene, Nitrile Rubber, Silver Shield, Viton. Respiratory Protection |No respiratory protection is normally required. If |user operations generate an oil mist, determine if |airborne concentrations are below the occupational |exposure limit for mineral oil mist. If not, wear an |approved respirator that provides adequate |protection from the measured concentrations of this |material. For air-purifying respirators use a |particulate cartridge. Use a positive pressure |air-supplying respirator in circumstances where |air-purifying respirators may not provide adequate |protection. Thermal Hazard Protection | SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1. Information on Basic Physical and Chemical Properties Physical State |Semi-solid Appearance | Odor |Petroleum odor Odor Threshold |No data available pH |Not Applicable Relative Evaporation Rate |No data available (butylacetate=1) | Melting Point |165Â°C (329Â°F) (Min) Freezing Point |No data available Boiling Point |260Â°C (500Â°F) Minimum Flash Point |274 Â°C (525 Â°F) Minimum Auto-ignition Temperature |No data available Decomposition Temperature |No Data Available Flammability (solid, gas) |No Data Available Vapor Pressure |<0.01 mmHg Maximum @ 100 Â°C (212 Â°F) Relative Vapor Density at 20 Â°C |>1 Minimum Relative Density |No data available Specific Gravity |1.1 @ 15.6Â°C (15.6Â°F) / 15.6Â°C (60.1Â°F) |(Estimated) Solubility |Soluble in hydrocarbons; insoluble in water Partition coefficient: | n-octanol/water | Viscosity |No data available Lower Flammable Limit |Not Applicable Upper Flammable Limit |Not Applicable 9.2. Other Information SECTION 10: STABILITY AND REACTIVITY 10.1 Reactivity May react with strong acids or strong oxidizing agents, such as chlorates, nitrates, peroxides, etc. 10.2 Chemical Stability This material is considered stable under normal ambient and anticipated storage and handling conditions of temperature and pressure. 10.3 Possibility of Hazardous Reactions Hazardous Polymerization: Hazardous polymerization will not occur. 10.4 Conditions to Avoid 10.5 Incompatible Materials Not applicable. 10.6 Hazardous Decomposition Products None known (None expected). Combustion Products: Highly dependent on combustion conditions. A complex mixture of airborne solids, liquids, and gases including carbon monoxide, carbon dioxide, and unidentified organic compounds will be evolved when this material undergoes combustion. SECTION 11: TOXICOLOGICAL INFORMATION 11.1. Information on Toxicological Effects Acute Toxicity: ADDITIONAL TOXICOLOGY INFORMATION: This product contains petroleum base oils which may be refined by various processes including severe solvent extraction, severe hydrocracking, or severe hydrotreating. None of the oils requires a cancer warning under the OSHA Hazard Communication Standard (29 CFR 1910.1200). These oils have not been listed in the National Toxicology Program (NTP) Annual Report nor have they been classified by the International Agency for Research on Cancer (IARC) as; carcinogenic to humans (Group 1), probably carcinogenic to humans (Group 2A), or possibly carcinogenic to humans (Group 2B). These oils have not been classified by the American Conference of Governmental Industrial Hygienists (ACGIH) as: confirmed human carcinogen (A1), suspected human carcinogen (A2), or confirmed animal carcinogen with unknown relevance to humans (A3). Skin Corrosion/Irritation: The skin irritation hazard is based on evaluation of data for product components. Serious Eye Damage/Irritation: The eye irritation hazard is based on evaluation of data for product components. Respiratory or Skin Sensitization: The skin sensitization hazard is based on evaluation of data for product components. Germ Cell Mutagenicity: The hazard evaluation is based on data for components or a similar material. Carcinogenicity: The hazard evaluation is based on data for components or a similar material. Reproductive Toxicity: The hazard evaluation is based on data for components or a similar material. Specific Target Organ Toxicity (Single Exposure): The hazard evaluation is based on data for components or a similar material. Specific Target Organ Toxicity (Repeated Exposure): The hazard evaluation is based on data for components or a similar material. Aspiration Hazard: Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: SECTION 12: ECOLOGICAL INFORMATION 12.1. Toxicity ECOTOXICITY: This material is expected to be harmful to aquatic organisms and may cause long-term adverse effects in the aquatic environment. The ecotoxicity hazard is based on an evaluation of data for the components or a similar material. The product has not been tested. The statement has been derived from the properties of the individual components. 12.2. Persistence and Degradability This material is not expected to be readily biodegradable. The biodegradability of this material is based on an evaluation of data for the components or a similar material. The product has not been tested. The statement has been derived from the properties of the individual components. 12.3. Bioaccumulative Potential Bioconcentration Factor: No data available. Octanol/Water Partition Coefficient: No data available. 12.4. Mobility in Soil No data available. 12.5. Other Adverse Effects SECTION 13: DISPOSAL CONSIDERATIONS 13.1. Waste treatment methods Waste Disposal Recommendations: Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations. Contact your sales representative or local environmental or health authorities for approved disposal or recycling methods. Additional Information: SECTION 14: TRANSPORT INFORMATION 14.1 In Accordance with DOT Proper Shipping Name |PETROLEUM LUBRICATING GREASEGREASE; NOT REGULATED AS A |HAZARDOUS MATERIAL FOR TRANSPORTATION UNDER 49 CFR Hazard Class | |<PICTOGRAM PHRASE> Identification Number| | Label Codes | | ERG Number | 14.2 In Accordance with IMDG Proper Shipping Name |PETROLEUM LUBRICATING GREASE; NOT REGULATED AS DANGEROUS |GOODS FOR TRANSPORT UNDER THE IMDG CODE Hazard Class | Identification Number| Label Codes | |<PICTOGRAM PHRASE> ntification Of The | | Substance/m | | EmS-No. (Fire) | | EmS-No. (Spillage) | | 14.3 In Accordance with IATA Proper Shipping Name |PETROLEUM LUBRICATING GREASE; NOT REGULATED AS DANGEROUS |GOODS FOR TRANSPORT UNDER ICAO Identification Number| |<PICTOGRAM PHRASE> Hazard Class | | Label Codes | | ntification Of The | | Substance/m | | ERG Code (IATA) | SECTION 15: REGULATORY INFORMATION 15.1 US Federal Regulations <COMPONENT> The following components of this material are found on the regulatory lists indicated. Zinc dialkyldithiophosphate 03, 06 SARA Section 311/312 Hazard Classes |1. Immediate (Acute) Health Effects: NO |2. Delayed (Chronic) Health Effects: NO |3. Fire Hazard: NO |4. Sudden Release of Pressure Hazard: NO |5. Reactivity Hazard: NO Toxic Substances Control Act (TSCA) |All components comply with the following |chemical inventory requirements: TSCA (United |States). 15.2 US State Regulations <COMPONENT> NEW JERSEY RTK CLASSIFICATION: Under the New Jersey Right-to-Know Act L. 1983 Chapter 315 N.J.S.A. 34:5A-1 et. seq., the product is to be identified as follows: PETROLEUM OIL (Grease). SECTION 16: OTHER INFORMATION, INCLUDING DATE OF PREPARATION OR LAST REVISION Revision date |OCTOBER 20, 2014 Other |This document has been prepared in accordance with the SDS Information |requirements of the OSHA Hazard Communication Standard 29 CFR |1910.1200. GHS Full Text Phrases: ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | Grainger disclaimer.
The information contained in this SDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'SDS' shall be created or inferred by any statement in this 'SDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'SDS'. The user is responsible for full compliance.