Product Categories See All
Track Order Status
MSDS Sheet 0055330Printer Friendly View
MSDS Material Safety Data "BLASTER"Â® Sheet The Blaster Corporation MSDS Number: ABD ABD-Aqueous-Based Revision Date: 07/17/07 Degreaser 1.PRODUCT AND COMPANY IDENTIFICATION Product Name: ABD-Aqueous-Based Degreaser Revision Date: 07/17/07 MSDS Number: ABD Product Code: 16-ABD, 32-ABD, 128-ABD, 5-ABD & 55-ABD Manufacturer: The Blaster Corporation 8500 Sweet Valley Drive Valley View, Ohio 44125 (216) 901-5800 (216) 901-5801 fax www.blasterproducts.com 2.COMPOSITION/INFORMATION ON INGREDIENTS CAS# Chemical Name % 7732-18-5 Water 85-95 Proprietary Ethoxylated alcohol 2-3 Proprietary Quarternary amine 2-3 compound 6834-92-0 Sodium Metasilicate 1-2 7758-29-4 Sodium Tripolyphosphate 1-2 64-02-8 NaEDTA 1-2 2836-32-0 Sodium glycolate <1 38011-25-5 Disodium <1 ethylenediaminediacetate 19019-43-3 Trisodium <1 ethylenediaminetriacetate 5064-31-3 Trisodium <1 nitrilotriacetate 1310-73-2 Sodium hydroxide <1 3. HAZARDS IDENTIFICATION Route of Entry: Eyes, skin, inhalation, ingestion Target Organs: Inhalation: Inhalation of spray mist likely to cause irritation to the respiratory tract. May cause headache, dizziness, nausea, vomiting or narcosis in confined or poorly ventilated areas. Skin Contact: Contact with skin is likely to cause irritation and dryness. May cause dermatitis or aggravate an existing condition. Eye Contact: Likely to cause immediate or delayed irritation. Irritation will show as redness and/or swelling of the eyes. Ingestion: Ingestion may cause irritation to the mouth, esophagus and stomach. May cause abdominal pain, vomiting, dizziness and headaches. 4. FIRST AID MEASURES Inhalation: Remove to fresh air. If not breathing, give artificial respiration. IF breathing is difficult, give oxygen. Continue to monitor. Get medical attention. Skin Contact: Remove contaminated clothing immediately! Wash skin with soap and water. If irritation develops, seek medical attention. Eye Contact: Flush eye(s) with water for 15 minutes. Get medical attention. If eye irritation persists, obtain medical treatment. Ingestion: If conscious, immediately give the person two large glasses of water. Do not induce vomiting. Get medical attention immediately. 5. FIRE FIGHTING MEASURES This is a water-based product and will not readily burn. Presents no unusual fire hazards. 6. ACCIDENTAL RELEASE MEASURES In case of spill or release, avoid vapors and ignition sources. Use appropriate protective devices and absorbents. Stop and contain the discharge if it can be done safely. Keep out of drains and waterways. Handle with trained personnel only. Notify authorities as required by law. 7. HANDLING AND STORAGE Handling Precautions: Use in accordance with good industrial workplace practices. Avoid unnecessary contact. Wash thoroughly after handling. Use with good ventilation. Storage Requirements: Keep containers tightly closed and in a cool well-ventilated place. Always store this material in closes labeled containers. Store away from acids. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Engineering Controls: Eye wash stations and emergency showers should be immediately available. Protective Equi9pments: Eyes and Face: Standard safety glasses with splash shields typically offer adequate protection. Where excessive splashing or spraying is possible, a face shield should be used. Do not wear contacts. Skin and clothing: Excessive contact should be avoided. Nitrile gloves, boots and aprons will provide adequate protection when contact cannot be avoided. Remove and wash any contaminated clothing immediately. Wash thoroughly after handling. Respiratory: Good general ventilation should be sufficient to control airborne levels. Maintain airborne concentrations below OSHA established exposure limits of ingredients in Section 2. Use NIOSH approved respirator if ventilation is not adequate enough to maintain levels below these limits. Exposure Guidelines/Other: The Blaster Corporation takes no responsibility for determining what measures are required for personal protection in any specific application. This information should be used with discretion. 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance: Sudsy straw colored Physical State: Liquid Boiling Point: >212 F Odor: Strong detergent-like Freezing/Melting PT.: <32F pH: >12 Solubility: Completely miscible Vapor Pressure: Not Determined Spec Grav./Density:1.02-1.03 Heat Value: Not Determined VOC: Not Determined Evap. Rate: Not Determined Bulk Density: Not Determined Octanol: Not Determined Molecular Weight: Not Determined Particle Size: Not Applicable Softening Point: Not Applicable Viscosity: Not Determined Percent Volatile: Not Determined Sat. Vap. Concentrat. Not Determined Molecular Formula: Not Determined 10. STABILITY AND REACTIVITY Stability: This product is stable. Conditions to avoid: Extreme temperatures. Materials to avoid (incompatibility): Avoid contact with acids. Hazardous Decomposition products: Smoke, Fumes, Oxides of Carbon and Nitrogen Hazardous Polymerization: Will not occur. 11. TOXICOLOGICAL INFORMATION Toxicological information on this product as a mixture has not been determined. See Section 15 for reportable ingredients. 12. ECOLOGICAL INFORMATION Ecological information on this product as a mixture has not been determined. 13. DISPOSAL CONSIDERATIONS Used or unused product should be disposed of in accordance with local, state and federal regulations. Empty containers may contain residual pressure and contents. They should be handled with the same precautions as the product. 14. TRANSPORT INFORMATION Dept. of Transportation (DOT): Proper shipping name: Corrosive Liquid, basic, inorganic, n.o.s. (Sodium Metasilicate) Hazard class: 8 UN #: 3266 Packing Group: III This product may be packaged to meet the definitions set forth in CFR 49 part 173.150 as a "consumer commodity." Allowing for certain exceptions (173.156) for domestic surface shipments. Please call The Blaster Corporation for clarification or questions regarding proper shipping information. 15. REGULATORY INFORMATION This product is not known to contain any SARA, Title III, Section 313 Reportable Chemicals at or greater than 1.0% (0.1% for carcinogens). All intentionally present components are listed on the TSCA inventory. 16. Manufacturer's Disclaimer: To the best of our knowledge, the information contained herein is accurate. However, neither The Blaster Company nor any of its subsidiaries assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards which exist. HMIS Ratings Health: 2 Fire: 0 Reactivity: 0
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'MSDS' shall be created or inferred by any statement in this 'MSDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'MSDS'. The user is responsible for full compliance.