Product Categories See All
Track Order Status
MSDS Sheet 0046164Printer Friendly View
MSDS - 4616-4 Material Safety Data Sheet The Blaster Corporation CBD Citrus Based Degreaser MSDS Number: CBD - bulk Revision Date: 08/25/08 1. PRODUCT AND COMPANY IDENTIFICATION Product Name: CBD Citrus Based Degreaser Revision Date: 08/25/08 MSDS Number: CBD - Bulk Product Code: 128-CBD, 5-CBD, 55-CBD Manufacturer: The Blaster Chemical Companies, Inc. 8500 Sweet Valley Drive Valley View, Ohio 44125 (216) 901-5800 (216) 901-5801 fax www.blasterproducts.com 24 Hour emergency Chemtrec (800) 424-9300 contact: 2. COMPOSITION / INFORMATION ON INGREDIENTS Ingredients: Cas # Chemical Name Perc. 64742478 Distillates, petroleum, hydrotreated 50-60% lig 5989275 Cyclohexene, 35-45% 1-methyl-1-(1-methylethenyl) 3. HAZARDS IDENTIFICATION Routes of Entry: Eyes, skin inhalation, ingestion Target Organs: Inhalation: Inhalation of spray mist may cause irritation to the respiratory tract. Skin Contact: Repeated or prolonged contact with skin may cause mild irritation and possibly dermatitis. Eye Contact: Likely to cause immediate or delayed irritation. Irritation will show as redness and or swelling of the eyes. Ingestion: Ingestion may cause irritation to the mouth, esophagus and stomach. May aggravate a pre-existing skin and respiratory disorders. Notice: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intention misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. 4. FIRST AID MEASURES Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Continue to monitor. Get medical attention. Skin Contact: Remove contaminated clothing immediately! Wash skin with soap and water. If irritation develops, seek medical attention. Eye Contact: Flush eye(s) with water for 15 minutes. Get medical attention. If eye irritation persists, obtain medical treatment. Ingestion: Do not induce vomiting! Get medical attention immediately! 5. FIRE FIGHTING MEASURES Flash Point: 130F ASTM D-56 (TCC) Extinguishing Dry chemical, carbon dioxide, halon or foam is recommended. media: Water spray may be used to cool containers or structures. Halon may decompose into toxic materials and carbon dioxide will displace oxygen. Take precautions when using these materials. General Fire and This material may be ignited by heat, sparks (static Explosion electricity), flame or other ignition sources. Vapors are Hazards: heavier than air and will collect in low areas (sewers) and can travel considerable distances. If containers are not cooled in a fire, they may explode. Fire Fighting Emergency responders should wear self-contained breathing Procedures: apparatus. Wear other protective gear as conditions warrant. Keep unauthorized people out. Try to contain spills or leaks if it can be done safely. Material will float on water. Avoid spreading. 6. ACCIDENTAL RELEASE MEASURES In case of spill or release, avoid vapors and ignition sources. Use appropriate protective devices and absorbents. Stop and contain the discharge if it can be done safely. Keep out of drains and waterways. Handle with trained personnel only. Notify authorities as required by law. 7. HANDLING AND STORAGE Handling Precautions: Use in accordance with good industrial workplace practices. Avoid unnecessary contact. Wash thoroughly after handling. Use with good ventilation. Storage Requirements: Store in a dry place away from excessive heat. Store containers with lids on and properly labeled. Do not store at temperatures above 120 degrees F. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering Controls: Eye wash stations and emergency showers should be immediately available. Protective Equipment: Eyes and Face: Standard safety glasses with splash shields typically offer adequate protection. Where excessive splashing or spraying is possible, a face shield should be used. Skin and clothing: Excessive contact should be avoided. Neoprene gloves, boots and aprons will provide adequate protection when contact cannot be avoided. Remove and wash any contaminated clothing immediately. Wash thoroughly after handling. Respiratory: Good general ventilation should be sufficient to control airborne levels. Maintain airborne concentrations below OSHA established exposure limits of ingredients in Section 2. Exposure The Blaster Chemical Companies takes no responsibility Guidelines/Other: for determining what measures are required for personal protection in any specific application. This information should be used with discretion. 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance: Clear Physical State: Liquid Odor: Citrus pH: Not determined Vapor Pressure: Not determined Vapor Density: >1 (air=1) Boiling Point: 180 F Freezing/Melting Pt.: Not determined Solubility: Soluble Spec Grav./Density: 0.837 (water=1) Heat Value: Not determined VOC: Not determined Evap. Rate: >1 (NBA = 1) Bulk Density: Not determined Octanol: Not applicable Molecular Weight: Not determined Particle Size: Not applicable Softening Point: Not applicable Viscosity: Not determined Percent Volatile: Not determined Sat. Vap. Concentrate.: Not determined Molecular Formula: Not determined 10. STABILITY AND REACTIVITY Stability: This product is stable. Conditions to avoid: Avoid excessive heat, sources of ignition and excessive water. Materials to avoid Avoid contact with strong oxidizing agents and (incompatibility): strong reducing agents (strong acids or bases.) Avoid mixture with water. Hazardous Decomposition Carbon monoxide, carbon dioxide, and various products: hydrocarbons. Hazardous Polymerization: Will not occur. 11. TOXICOLOGICAL INFORMATION Toxicological information on this product as a mixture has not been determined. See section 15 for reportable ingredients. 12. ECOLOGICAL INFORMATION Ecological information on this product as a mixture has not been determined. 13. DISPOSAL CONSIDERATIONS Used or unused product should be disposed of in accordance with local, state and abd federal regulations. Some special regulations may exist for the disposal of empty aerosol containers. Empty containers may contain residual pressure and contents. They should be handled with the same precautions as the product. 14. TRANSPORT INFORMATION Dept. of Transportation (DOT): Proper shipping Flammable Liquid, n.o.s. (naptha) name: Hazard class: 3 UN #: 1993 Packing Group: III This product may be packaged to meet the definitions set forth in CFR 49 part 173.150c as a "consumer commodity." Allowing for certain exceptions (173.156) for domestic surface shipments. Please call The Blaster Chemical Companies for clarification or questions regarding proper shipping information. 15. REGULATORY INFORMATION. This product is not known to contain any SARA, Title III, Section 313 Reportable Chemicals at a greater than 1.0% (0.1% for carcinogens.) 16. OTHER INFORMATION Manufacturer's Disclaimer: To the best of our knowledge, the information contained herein is accurate. However, neither The Blaster Chemical Companies nor any of its subsidiaries assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazard which exists. HMIS Ratings: Health: 1 Fire: 2 Reactivit 0 y:
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'MSDS' shall be created or inferred by any statement in this 'MSDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'MSDS'. The user is responsible for full compliance.