Product Categories See All
Track Order Status
Sheet 0077510Printer Friendly View
SECTION 1: IDENTIFICATION 1.1. Product Identifier Product Form: Product Name: Manus Bond 73GP Black CAS No: Synonyms: 1.2. Intended Use of the Product Use of the substance/mixture: adhesives / sealant 1.3. Name, Address, and Telephone of the Responsible Party Company Manus Products, Inc. 866 Industrial Blvd. West Waconia, MN 55387 Phone: (952) 442-3323 1.4. Emergency Telephone Number Emergency |(800) 424-9300 number | SECTION 2: HAZARDS IDENTIFICATION 2.1. Classification of the Substance or Mixture Classification (GHS-US) Not a | hazardous | substance or | mixture. | | | 2.2. Label Elements GHS-US Labeling Hazard Pictograms (GHS-US) |None Signal Word (GHS-US) |None Hazard Statements (GHS-US) |None Precautionary Statements |Prevention: (GHS-US) |P271 Use only outdoors or in a well-ventilated area. 2.3. Other Hazards Other Hazards Not Contributing to the Classification: None known. 2.4. Unknown Acute Toxicity (GHS-US) SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS 3.1. Substance Name |Product identifier |% |Classification | | |(GHS-US) | | | | | | | | | | | | | | | Full text of H-phrases: See Section 16 3.2. Mixture Name |Product identifier |% |Classification | | |(GHS-US) Distillates (petroleum), |64742-46-7 |>= 20 - | hydrotreated middle | |< 30 | Silicon dioxide |7631-86-9 |>= 5 - <| | |10 | Titanium dioxide |13463-67-7 |>= 0.1 -| | |< 1 | Carbon black |1333-86-4 |>= 0.1 -| | |< 1 | | | | SECTION 4: FIRST AID MEASURES 4.1. Description of First Aid Measures First-aid Measures General: In the case of accident or if you feel unwell, seek medical advice immediately. When symptoms persist or in all cases of doubt seek medical advice. First Aid responders should pay attention to self-protection, and use the recommended personal protective equipment when the potential for exposure exists. First-aid Measures After Inhalation: If inhaled, remove to fresh air. Get medical attention if symptoms occur. First-aid Measures After Skin Contact: Wash with water and soap as a precaution. Get medical attention if symptoms occur. First-aid Measures After Eye Contact: Flush eyes with water as a precaution. Get medical attention if irritation develops and persists. First-aid Measures After Ingestion: If swallowed, DO NOT induce vomiting. Get medical attention if symptoms occur. Rinse mouth thoroughly with water. 4.2. Most important symptoms and effects, both acute and delayed Symptoms/Injuries: None known. Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: 4.3. Indication of Any Immediate Medical Attention and Special Treatment Needed Notes to physician: Treat symptomatically and supportively. SECTION 5: FIRE-FIGHTING MEASURES 5.1. Extinguishing Media Suitable Extinguishing Media: Water spray Alcohol-resistant foam Dry chemical Carbon dioxide (CO2). Unsuitable Extinguishing Media: None known. 5.2. Special Hazards Arising From the Substance or Mixture Fire Hazard: Exposure to combustion products may be a hazard to health. Explosion Hazard: Carbon oxides Silicon oxides Formaldehyde. Reactivity: 5.3. Advice for Firefighters Precautionary Measures Fire: Firefighting Instructions: Use extinguishing measures that are appropriate to local circumstances and the surrounding environment. Use water spray to cool unopened containers. Remove undamaged containers from fire area if it is safe to do so. Evacuate area. Protection During Firefighting: In the event of fire, wear self-contained breathing apparatus. Use personal protective equipment. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal Precautions, Protective Equipment and Emergency Procedures General Measures: Use personal protective equipment. Follow safe handling advice and personal protective equip-ment recommendations. 6.1.1. For Non-emergency Personnel Protective Equipment: Emergency Procedures: 6.1.2. For Emergency Responders Protective Equipment: Emergency Procedures: 6.2. Environmental Precautions Discharge into the environment must be avoided. Prevent further leakage or spillage if safe to do so. Retain and dispose of contaminated wash water. Local authorities should be advised if significant spillages cannot be contained. 6.3. Methods and Material for Containment and Cleaning Up For Containment: Methods for Cleaning Up: Soak up with inert absorbent material. For large spills, provide diking or other appropriate containment to keep material from spreading. If diked material can be pumped, store recovered material in appropriate container. Clean up remaining materials from spill with suitable absorbent. Local or national regulations may apply to releases and disposal of this material, as well as those materials and items employed in the cleanup of releases. You will need to deter- mine which regulations are applicable. Sections 13 and 15 of this SDS provide information regarding certain local or national requirements. 6.4. Reference to Other Sections See heading 8, Exposure Controls and Personal Protection. SECTION 7: HANDLING AND STORAGE 7.1. Precautions for Safe Handling Additional Hazards When Processed: Do not swallow. Avoid contact with eyes. Avoid prolonged or repeated contact with skin. Handle in accordance with good industrial hygiene and safety Practice. Take care to prevent spills, waste and minimize release to the environment. Hygiene Measures: Ensure that eye flushing systems and safety showers are located close to the working place. When using do not eat, drink or smoke. Wash contaminated clothing before re-use. These precautions are for room temperature handling. Use at elevated temperature or aerosol/spray applications may re- quire added precautions. 7.2. Conditions for Safe Storage, Including Any Incompatibilities Technical Measures: See Engineering measures under EXPOSURE CONTROLS/PERSONAL PROTECTION section. Storage Conditions: Keep in properly labeled containers. Store in accordance with the particular national regulations. Materials to avoid: Do not store with the following product types: Strong oxidizing agents. 7.3. Specific End Use(s) SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1. Control Parameters Ingredients with workplace control parameters: Ingredients CAS-No. Value type Form of exposure) Control parameters / Permissible concentration Basis Distillates (petroleum), hydrotreated middle 64742-46-7 TWA (Mist) TWA (Mist) TWA (Mist) ST (Mist) 5 mg/m3 5 mg/m3 5 mg/m3 10 mg/m3 OSHA Z-1 OSHA P0 NIOSH REL NIOSH REL Silicon dioxide 7631-86-9 TWA (Dust) TWA (Dust) TWA 20 Million particles per cubic foot (Silica) 80 mg/m3 / %SiO2 (Silica) 6 mg/m3 (Silica) OSHA Z-3 OSHA Z-3 NIOSH REL Titanium dioxide 13463-67-7 TWA (total dust) TWA 15 mg/m3 10 mg/m3 (Titanium dioxide) OSHA Z-1 ACGIH Carbon black 1333-86-4 TWA TWA TWA (Inhalable fraction) 3.5 mg/m3 3.5 mg/m3 3 mg/m3 NIOSH REL OSHA Z-1 ACGIH 8.2. Exposure Controls Appropriate Engineering |Processing may form hazardous compounds (see section Controls |10). Ensure adequate ventilation, especially in |confined areas. Minimize workplace exposure |concentrations. Personal Protective Equipment| Materials for Protective | Clothing | Hand Protection |Material: Impervious gloves. |Remarks: Choose gloves to protect hands against |chemicals depending on the concentration specific to |place of work. Breakthrough time is not determined |for the product. Change gloves often! For special |applications, we recommend clarifying the resistance |to chemicals of the aforementioned protective gloves |with the glove manufacturer. Wash hands before |breaks and at the end of workday. Eye Protection |Wear the following personal protective equipment: |Safety glasses. Skin and Body Protection |Skin should be washed after contact. Respiratory Protection |General and local exhaust ventilation is recommended |to maintain vapor exposures below recommended |limits. Where concentrations are above recommended |limits or are unknown, appropriate respiratory |protection should be worn. Follow OSHA respirator |regulations (29 CFR 1910.134) and use NIOSH/MSHA |approved respirators. Protection provided by air |purifying respirators against exposure to any |hazardous chemical is limited. Use a positive |pressure air supplied respirator if there is any |potential for uncontrolled release, exposure levels |are unknown, or any other circumstance where air |purifying respirators may not provide adequate |protection. Thermal Hazard Protection | SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1. Information on Basic Physical and Chemical Properties Physical State | Appearance |paste Odor |Acetic acid Odor Threshold |No data available pH |Not applicable Relative Evaporation Rate |Not applicable (butylacetate=1) | Melting Point |No data available Freezing Point |No data available Boiling Point |Not applicable Flash Point |> 100 �C Method: closed cup Auto-ignition Temperature |No data available Decomposition Temperature |No data available Flammability (solid, gas) |Not classified as a flammability hazard Vapor Pressure |Not applicable Relative Vapor Density at 20 �C |No data available Relative Density |0.96 Specific Gravity | Solubility |No data available Partition coefficient: |No data available n-octanol/water | Viscosity |200,000 mPa.s Lower Flammable Limit |No data available Upper Flammable Limit |No data available 9.2. Other Information SECTION 10: STABILITY AND REACTIVITY 10.1 Reactivity Not classified as a reactivity hazard. 10.2 Chemical Stability Stable under normal conditions. 10.3 Possibility of Hazardous Reactions Use at elevated temperatures may form highly hazardous compounds. Can react with strong oxidizing agents. Acetic acid is formed upon contact with water or humid air. Hazardous decomposition products will be formed at elevated temperatures. 10.4 Conditions to Avoid None known. 10.5 Incompatible Materials Oxidizing agents. 10.6 Hazardous Decomposition Products Formaldehyde. SECTION 11: TOXICOLOGICAL INFORMATION 11.1. Information on Toxicological Effects Acute Toxicity: Not classified based on available information. Skin Corrosion/Irritation: Not classified based on available information. Serious Eye Damage/Irritation: Not classified based on available information. Respiratory or Skin Sensitization: Skin sensitization: Not classified based on available information. Respiratory sensitization: Not classified based on available information. Germ Cell Mutagenicity: Not classified based on available information. Carcinogenicity: Not classified based on available information. Reproductive Toxicity: Not classified based on available information. Specific Target Organ Toxicity (Single Exposure): Not classified based on available information. Specific Target Organ Toxicity (Repeated Exposure): Not classified based on available information. Aspiration Hazard: Not classified based on available information. Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: SECTION 12: ECOLOGICAL INFORMATION 12.1. Toxicity Titanium dioxide: Toxicity to fish: LC50 (Oncorhynchus mykiss (rainbow trout)): > 100 mg/l Exposure time: 96 h Method: OECD Test Guideline 203 Toxicity to daphnia and other aquatic invertebrates: EC50 (Daphnia magna (Water flea)): > 100 mg/l Exposure time: 48 h Toxicity to algae: EC50 (Skeletonema costatum (marine diatom)): > 10,000 mg/l Exposure time: 72 h Toxicity to bacteria: EC50: > 1,000 mg/l Exposure time: 3 h Method: OECD Test Guideline 209 Carbon black: Toxicity to fish: LC0 (Danio rerio (zebra fish)): 1,000 mg/l Exposure time: 96 h Method: OECD Test Guideline 203 Toxicity to daphnia and other aquatic invertebrates: EC50 (Daphnia magna (Water flea)): > 5,600 mg/l Exposure time: 24 h Method: OECD Test Guideline 202 Toxicity to algae: NOEC (Desmodesmus subspicatus (green algae)): 10,000mg/l Exposure time: 72 h Method: OECD Test Guideline 201 12.2. Persistence and Degradability No data available. 12.3. Bioaccumulative Potential No data available. 12.4. Mobility in Soil No data available. 12.5. Other Adverse Effects No data available. SECTION 13: DISPOSAL CONSIDERATIONS 13.1. Waste treatment methods Waste Disposal Recommendations: Resource Conservation and Recovery Act (RCRA) : This product has been evaluated for RCRA characteristics and does not meet the criteria of hazardous waste if discarded in its purchased form. Waste from residues: Dispose of in accordance with local regulations. Additional Information: Contaminated packaging: Dispose of as unused product. Empty containers should be taken to an approved waste handling site for recycling or disposal. SECTION 14: TRANSPORT INFORMATION 14.1 In Accordance with DOT Proper Shipping Name | Hazard Class | |<PICTOGRAM PHRASE> Identification Number| | Label Codes | | ERG Number | 14.2 In Accordance with IMDG Proper Shipping Name |Not regulated as a dangerous good Hazard Class | Identification Number| Label Codes | |<PICTOGRAM PHRASE> ntification Of The | | Substance/m | | EmS-No. (Fire) | | EmS-No. (Spillage) | | 14.3 In Accordance with IATA Proper Shipping Name |Not regulated as a dangerous good Identification Number| |<PICTOGRAM PHRASE> Hazard Class | | Label Codes | | ntification Of The | | Substance/m | | ERG Code (IATA) | SECTION 15: REGULATORY INFORMATION 15.1 US Federal Regulations <COMPONENT> EPCRA - Emergency Planning and Community Right-to-Know: CERCLA Reportable Quantity: Ingredients CAS-No. Component RQ (lbs) Calculated product RQ (lbs) Acetic acid 64-19-7 5000 * Acetic anhydride 108-24-7 5000 * *: Calculated RQ exceeds reasonably attainable upper limit. SARA 304 Extremely Hazardous Substances Reportable Quantity: Ingredients CAS-No. Component RQ (lbs) Calculated product RQ (lbs) 10,10-Oxydiphenoxarsine 58-36-6 500 * *: Calculated RQ exceeds reasonably attainable upper limit. SARA 302: No chemicals in this material are subject to the reporting requirements of SARA Title III, Section 302. SARA 313: This material does not contain any chemical components with known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313. SARA Section 311/312 Hazard Classes |No SARA Hazards. Toxic Substances Control Act (TSCA) |All chemical substances in this material are |included on or exempted from listing on the |TSCA Inventory of Chemical Substances. 15.2 US State Regulations <COMPONENT> Pennsylvania Right To Know: Dimethyl siloxane, hydroxy-terminated 70131-67-8 50 - 70 Distillates (petroleum), hydrotreated middle 64742-46-7 20 - 30 Silicon dioxide 7631-86-9 5 - 10 Aluminium 7429-90-5 0 - 0.1 Acetic acid 64-19-7 0 - 0.1 Acetic anhydride 108-24-7 0 - 0.1 New Jersey Right To Know: Dimethyl siloxane, hydroxy-terminated 70131-67-8 50 - 70 Distillates (petroleum), hydrotreated middle 64742-46-7 20 - 30 Silicon dioxide 7631-86-9 5 - 10 Carbon black 1333-86-4 0.1 - 1 California Prop 65: WARNING! This product contains a chemical known in the State of California to cause cancer. Cobalt titanite green spinel 68186-85-6 SECTION 16: OTHER INFORMATION, INCLUDING DATE OF PREPARATION OR LAST REVISION Revision date | Other |This document has been prepared in accordance with the SDS Information |requirements of the OSHA Hazard Communication Standard 29 CFR |1910.1200. GHS Full Text Phrases: ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | Grainger disclaimer.
The information contained in this was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this '' shall be created or inferred by any statement in this ''. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this ''. The user is responsible for full compliance.