Product Categories See All
Track Order Status
MSDS Sheet 0076084Printer Friendly View
MATERIAL SAFETY DATA SHEET 1. PRODUCT AND COMPANY IDENTIFICATION Material Identification Product ID: DSL201, 250, 321, 325, 328, 100, 105 Product Name: DRI-SLIDE MULTIPURPOSE LUBRICANT Product Use: LUBRICANT Print date: 21/May/2007 Revision date:26/Feb/2007 Company Identification The Valspar Corportation 1101 Third Street South Minneapolis, MN 55415 Manufacturer's Phone: 1-612-332-7371 24-Hour Medical Emergency Phone: 1-888-345-5732 2. COMPOSITION/INFORMATION ON HAZARDOUS INGREDIENTS Common Name Approx.Weight % Chemical name CAS-No. MINERAL SPIRITS 65-70 Stoddard solvent 8052-41-3 1,3,5-TRIMETHYLBENZENE 1-5 1,3,5-Trimethylbenzene 108-67-8 1,2,4-TRIMETHYLBENZENE 1-5 PSEUDO CUMENE 95-63-6 PROPRIETARY PIGMENT 1-5 Graphite XYLENE 1330-20-7 1-5 Xylenes (o-,m-,p- isomers) If this section is blank there are no hazardous components per OSHA guidelines. 3. HAZARDS IDENTIFICATION Primary Routes of Exposure: Inhalation Ingestion Skin absorption Emergency Overview; This section not in use. This product contains ingredients that may contribute to the following potential acute health effects: Inhalation Effects: May cause irritation of the respiratory tract and systemic toxicity. Eye Contact: May cause moderate eye irritation. Skin Contact: May cause moderate skin irriation. Acute Ingestion: Irritation of gastrointestinal tract. Other Effects: May cause liver damage. May cause kidney damage. This product contains ingredients that may contribute to the following potential chronic health effects: Notice: Reports have been associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. Prolonged and/or repeated contact can result in skin irritation. See Section 11 for toxicological information about Mutagens, Teratogens and Carcinogens. If this section is blank, no further information is available. 4. FIRST AID MEASURES Inhalation If affected by inhalation, move victim to fresh air. If symptoms persist, seek medical attention. If inhaled, remove from area to fresh air. Get medical attention if respiratory irritation develops or if breathing becomes difficult. Eye Contact In case of contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical attention if irritation persists. Skin Contact In case of contact, immediately flush skin with plenty of soap and water for at least 15 minutes. If irritation persists get medical attention. Wash with soap and water. Ingestion If swallowed, do not induce vomiting. Give large quantities of water. If available, give several glasses of milk. Never give anything by mouth to an unconscious person. Get medical attention immediately. If swallowed, get medical attention immediately. Get medical attention. Do not induce vomiting/risk of damage tolungs exceeds poisoning risk. Medical conditions aggravated by exposure: Any respiratory or skin condition. 5. FIRE FIGHTING MEASURES Flash Point (Fahrenheit): 104F (40 C) TCC/PM Lower explosive limit: 1% Upper explosive limit: 6% Autoignition temperature: Not available. F ( C) Sensitivity to impact: No Sensitivity to static discharge: Can be sensitive to static discharge hazards. Please see bonding and grounding information in Section 7. Hazardous combustion products: See Section 10. Unusual fire and explosion hazards: None known. Extinguishing media: Carbon dioxide, dry chemical, foam and/or water fog. Fire-fighting Procedures: Use water spray to cool nearby containres and structures exposed to fire. 6. ACCIDENTAL RELEASE MEASURES Action to be taken if material is released or spilled: Ventilate area. Avoid breathing of vapors. Use self-containing breathing apparatus or airmask for large spills in a confined area. Wipe, scrape or soak up in an inert material and put in a container for disposal.See section 5, "Unusual Fire and Explosion Hazards", for proper container and storage procedures. Remove sources of ignition. Remove with inert abosorbent and non sparking tools. Avoid contact with eyes. 7. HANDLING AND STORAGE Precautions to be taken in handling and storage: Keep away from hat, sparks, and flames. Keep container closed when not in use. Do not store above 120 degrees F. (49 degrees C). Based on flash point and vapor pressure, suitable storage should be provided in accordance with OSHA regulation 1910.106, Ontario OH&S regulation 851 section 22. Empty containers may contain product residue, including flammable or explosive vapors. Do not cut, puncture or weld on or near container. All label warnings must be observed until the container has been commercially cleaned or reconditioned. If the product is used near or above the flashpoint, an ignition hazard may be present. Activities, uses, or operations which liberate vapor (such as mixing or free fall of liquids) may also present an ignition hazard. Please ensure containers and other interconnected equipment are properly bonded and grounded at all times. 8. PERSONAL PROTECTIVE EQUIPMENT AND EXPOSURE CONTROLS Personal Protective Equipment Eye and face protection: Avoid contact with eyes. Wear chemical goggles if there is the possibility of contact or splashing in the eye. Skin protection: Appropriate chemical resistant gloves should be worn. To prevent skin contact wear protective clothing covering exposed areas. Respiratory protection: If exposure cannot be controlled the below applicable limits, use the appropriate NIOSH approved respirator such as an air purifying respirator with organic vapor cartridge and dust/mist filter. Consult the respirator manufacuturer's literature to ensure that the respirator will provide adequate protection. Read and follow all respirator manufacturer's instructions. Ventilation Required when spraying or applying in confined area. Ventilation equipment should be explosion proof. Exposure Guidelines OSHA Permissible Exposure Limits (PEL's) Common Name Approx. TWA (final) Ceilings limits Skin CAS-No. Weight% (final) designations MINERAL SPIRITS 65-70 2900 mg/m3 500 ppm 8052-41-3 PROPRIETARY PIGMENT 1-5 Listed. XYLENE 1-5 435 mg/m3 100 ppm 1330-20-7 ACGIH Threshold Limit Value (TLV's) Common Name Approx. TWA STEL Ceiling Skin CAS-No. Weight % limits designations MINERAL SPIRITS 65-70 100 ppm 1,3,5 TRIMETHYL- 1-5 25 ppm BENZENE 108-67-8 1,2,4-TRIMETHYL- 1-5 25 PPM BENZENE 95-63-6 PROPRIETARY 1-5 2 mg/m3 PIGMENT Respirable fraction. XYLENE 1-5 100 ppm 150 ppm 1330-20-7 If this section is blank, no information is available. 9. PHYSICAL PROPERTIES Odor: Normal for this product type. Physical State: Liquid pH: Not determined. Vapor Pressure: 6 mmHG@68F (20 C) Vapor density (air=1.0): 4.8 Boiling point: 282 F (139 C) Solubility in water: Insoluble. Coefficient of water/oil distribution: Not determined. Density (lbs per US gallon): 7.16 Specific Gravity: .86 Evaporation rate (butyl acetate=1.0) .6 10. STABILITY AND REACTIVITY Stable: Stable Conditions to Avoid: None known. Incompatibility; Strong oxidizers Hazardous Polymerization: None anticipated Hazardous Decomposition Products: Carbon monoxide and crbon dioxide. Oxides of sulfur. Sensitivity to static discharge: Can be sensitive to static discharge hazards. Please see bonding and grounding information in Section 7. 11. TOXICOLOGICAL INFORMATION Mutagens: Teratogens: Carcinogens: If this section is blank, no information is available. 12. ECOLOGICAL DATA Not available at this time. 13. DISPOSAL CONSIDERATIONS Disposal should be made in accordance with federal, state and local regulations. 14. TRANSPORTATION INFORMATION U.S. Department of Transportation Proper Shipping Name: LUBRICANT, NOT REGULATED UN ID Number: NRLUBE Hazardous Ingredient XYLENE (Land) 1 U.S. Highway & Rail Shipments The supplier may apply one of the following exceptions: Combustible liquid, Consumer Commodity, Limited Quantity, Viscous Liquid, Does Not Sustain Combustion,or others, as allowd under 49CFR Hazmat Regulations. Please consult 49CFR Subchapter C to ensure that subsequent shipments comply with these exceptions. International Air Transport Association: Proper Shipping Name: Contact Supplier for further information. IATA N.O.S. Technical Name 1 XYLENE International Maritime Organization Proper Shipping Name: Contact Supplier for further information. IMDG N.O.S. Technical Name 1 XYLENE 15. REGULATORY INFORMATION U.S. FEDERAL REGULATIONS: Common Name Approx. SARA 302 SARA 13 CERCLA RQ in lbs. CAS-NO. Weight % 1,3,5-TRIMETHYL- 1-5 YES BENZENE 108-67-8 1,2,4-TRIMETHYL- 1-5 Listed. BENZENE XYLENE 1-5 for R reporting required 100 1330-20-7 for 1.0% de minimis concentration SARA 311/312 Hazard Class: Acute; Yes Chronic; Yes Flammability; Yes Reactivity; No Sudden Pressure; No U.S. STATE REGULATIONS: Pennsylvania Right To know: 1,3,5-TRMETHYLBENZENE 108-67-8 XYLENE 1330-20-7 DISTILLATES, PETROLEUM, HYDROTREATED HEAVY NAPTHE 64742-52-5 PROPRIETARY PIGMENT Trade Secret MINERAL SPIRITS 8052-41-3 1,2,4-TRIMETHYLBENZENE 95-63-6 Additional Non-Hazardous Materials PROPRIETARY PIGMENT Trade Secret SUPPLIER TRADE SECRET Trade Secret Rule 66 Status of product Photochemically reactive. INTERNATIONAL REGULATIONS- Chemical Inventories TSCA Inventory: All components of this product are in compliance wth U.S. TSCA Chemical Substance Inventory Requirements. Canada Domestic Substances List: All components of this product are listed on the Domestic Substance List. 16. OTHER INFORMATION HMIS Codes Health: 2 Flammability: 2 Reactivity: 1 PPE: X-See Section 8 for Personal Protective Equipment (PPE). Abbreviations: OSHA-Occupational Safety and Health Administration, IARC-International Agency for Research on Cancer, NIOSH-National Institute of Occupational Safety and Health, NTP-National Toxicology Program, ACGIH-American Conference of Governmental Industrial Hygienists, SCAQMD-South Coast Air Quality Management District, TSCA-Toxic Substances Control Act, IATA-International Air Transport Association, IMO-International Maritime Organization, DOT-Department of Transporation, NA-Not Applicable, NOT ESTAB-Not established, N.A.V.-Not available, RQ-Reportable Quantity, WT-Weight, MG/CU M- Milligrams per cubic metr, G/L- Grams per liter, MM-Millimeters, MPPCF-Millions of particles per cubic feet, PPM- parts per million, PPT- parts per thousand, TCC/PM- Tag closed cup/Pensky-Martens, PB-Lead, PEL-Permissible exposure level, TWA-Time Weighted Average, STEL-Short term exposure limit, C-Celsius, F-Fahrenheit. Disclaimer: The data on this sheet represents typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information. UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES NO WARRANTIES, EXPRESSEDOR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product is the replacement of the defective product, or a refund of its purchase price, at ouroption.This MSDS contains additional information required by the state of Pennsylvania.
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'MSDS' shall be created or inferred by any statement in this 'MSDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'MSDS'. The user is responsible for full compliance.