Product Categories See All
Track Order Status
SDS Sheet 0075220Printer Friendly View
SECTION 1: IDENTIFICATION | |1.1. Product Identifier Product Form: Product Name: 3M Fast Tack Trim Adhesive, P.N. 08031, 08033, 08034 CAS No: Synonyms: 1.2. Intended Use of the Product Use of the substance/mixture: 1.3. Name, Address, and Telephone of the Responsible Party Company 3M DIVISION: Automotive Aftermarket 3M Center, St. Paul, MN 55144-1000, USA Phone: 1-888-3M HELPS (1-888-364-3577) 1.4. Emergency Telephone Number Emergency | 1-800-364-3577 or (651) 737-6501 (24 hours) number | | SECTION 2: HAZARDS IDENTIFICATION 2.1. Classification of the Substance or Mixture Classification (GHS-US) Serious Eye |Category 2B Damage/Irritat| ion | Flammable |Category 2 Liquid | Reproductive |Category 2 Toxicity | Specific |Category 1 Target Organ | Toxicity | (repeated | exposure): | Specific |Category 3 Target Organ | Toxicity | (central | nervous | system): | 2.2. Label Elements GHS-US Labeling Hazard Pictograms (GHS-US) |Flame |Exclamation Mark |Health Hazard Signal Word (GHS-US) |Danger Hazard Statements (GHS-US) |Highly flammable liquid and vapor. |Causes eye irritation. |May cause drowsiness or dizziness. |Suspected of damaging fertility or the unborn child. | |Causes damage to organs through prolonged or |repeated exposure: nervous system Precautionary Statements |General: (GHS-US) |Keep out of reach of children. |Prevention: |Obtain special instructions before use. |Do not handle until all safety precautions have been |read and understood. |Keep away from heat/sparks/open flames/hot surfaces. |- No smoking. |Ground/bond container and receiving equipment. |Use only non-sparking tools. |Take precautionary measures against static |discharge. |Keep container tightly closed. |Use explosion-proof electrical/ventilating/lighting |equipment. |Do not breathe dust/fume/gas/mist/vapors/spray. |Use only outdoors or in a well-ventilated area. |Wear protective gloves and eye/face protection. |Do not eat, drink or smoke when using this product. |Wash thoroughly after handling. |Response: |IF INHALED: Remove person to fresh air and keep |comfortable for breathing. |IF ON SKIN (or hair): Take off immediately all |contaminated clothing. Rinse skin with water/shower. | |IF IN EYES: Rinse cautiously with water for several |minutes. Remove contact lenses, if present and easy |to do. |Continue rinsing. |If eye irritation persists: Get medical |advice/attention. |IF exposed or concerned: Get medical |advice/attention. |In case of fire: Use a fire fighting agent suitable |for flammable liquids and solids such as dry |chemical or carbon dioxide |to extinguish. |Storage: |Store in a well-ventilated place. Keep cool. |Keep container tightly closed. |Store locked up. |Disposal: |Dispose of contents/container in accordance with |applicable local/regional/national/international |regulations. 2.3. Other Hazards Other Hazards Not Contributing to the Classification: 8% of the mixture consists of ingredients of unknown acute oral toxicity. 2.4. Unknown Acute Toxicity (GHS-US) SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS 3.1. Substance Name |Product identifier |% |Classification | | |(GHS-US) HEXANE |110-54-3 |30 - 60 | | |Trade | | |Secret *| 3-METHYLPENTANE |96-14-0 |10 - 35 | | |Trade | | |Secret *| STYRENE-BUTADIENE POLYMER |9003-55-8 |7 - 13 | | |Trade | | |Secret *| 2-METHYLPENTANE |107-83-5 |3 - 10 | | |Trade | | |Secret *| METHYLCYCLOPENTANE |96-37-7 |3 - 10 | | |Trade | | |Secret *| DICYCLOPENTADIENE-INDENE-.ALPHA.|68240-01-7 |3 - 7 | - | |Trade | METHYLSTYRENE-STYRENE-VINYLTOLUE| |Secret *| NE | | | COPOLYMER | | | GLYCEROL ESTER OF HYDROGENATED |65997-13-9 |1 - 5 | ROSIN | |Trade | | |Secret *| HYDROCARBON RESIN |68131-87-3 |1 - 5 | | |Trade | | |Secret *| WATER |7732-18-5 |1 - 5 | | |Trade | | |Secret *| CALCIUM ZINC RESINATE |68334-35-0 |1 - 5 | | |Trade | | |Secret *| HYDROTREATED HEAVY NAPHTHENIC |64742-52-5 |0.1 -1 | PETROLEUM DISTILLATES | |Trade | | |Secret *| 4,4'-THIOBIS(6-TERT-BUTYL-M-CRES|96-69-5 |< 1 | OL) | |Trade | | |Secret *| ETHYL ALCOHOL |64-17-5 |0.1 - 1 | | |Trade | | |Secret *| SOLVENT-REFINED HEAVY PARAFFINIC|64741-88-4 |< 0.6 | | |Trade | PETROLEUM DISTILLATES | |Secret *| METHYL ALCOHOL |67-56-1 |<0.05 | | |Trade | | |Secret *| METHYL ISOBUTYL KETONE |108-10-1 |<0.05 | | |Trade | | |Secret *| Full text of H-phrases: See Section 16 3.2. Mixture Name |Product identifier |% |Classification | | |(GHS-US) | | | | | | | | | | | | | | | SECTION 4: FIRST AID MEASURES 4.1. Description of First Aid Measures First-aid Measures General: First-aid Measures After Inhalation: Remove person to fresh air. If you feel unwell, get medical attention. First-aid Measures After Skin Contact: Immediately wash with soap and water. Remove contaminated clothing and wash before reuse. If signs/symptoms develop, get medical attention. First-aid Measures After Eye Contact: Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get medical attention. First-aid Measures After Ingestion: If Swallowed: Rinse mouth. If you feel unwell, get medical attention. 4.2. Most important symptoms and effects, both acute and delayed Symptoms/Injuries: Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: 4.3. Indication of Any Immediate Medical Attention and Special Treatment Needed Not applicable SECTION 5: FIRE-FIGHTING MEASURES 5.1. Extinguishing Media Suitable Extinguishing Media: In case of fire: Use a fire fighting agent suitable for flammable liquids and solids such as dry chemical or carbon dioxide to extinguish. Unsuitable Extinguishing Media: 5.2. Special Hazards Arising From the Substance or Mixture Fire Hazard: Explosion Hazard: Reactivity: Closed containers exposed to heat from fire may build pressure and explode. 5.3. Advice for Firefighters Precautionary Measures Fire: Firefighting Instructions: Protection During Firefighting: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and prevent explosive rupture. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal Precautions, Protective Equipment and Emergency Procedures General Measures: Evacuate area. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Use only non-sparking tools. Ventilate the area with fresh air. Refer to other sections of this SDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. 6.1.1. For Non-emergency Personnel Protective Equipment: Emergency Procedures: 6.1.2. For Emergency Responders Protective Equipment: Emergency Procedures: 6.2. Environmental Precautions Avoid release to the environment. For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water. 6.3. Methods and Material for Containment and Cleaning Up For Containment: Contain spill. Cover spill area with a fire-extinguishing foam. An appropriate aqueous film forming foam (AFFF) is recommended. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible using non-sparking tools. Place in a metal container approved for transportation by appropriate authorities. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and SDS. Seal the container. Dispose of collected material as soon as possible. Methods for Cleaning Up: Contain spill. Cover spill area with a fire-extinguishing foam. An appropriate aqueous film forming foam (AFFF) is recommended. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible using non-sparking tools. Place in a metal container approved for transportation by appropriate authorities. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and SDS. Seal the container. Dispose of collected material as soon as possible. 6.4. Reference to Other Sections See heading 8, Exposure Controls and Personal Protection. SECTION 7: HANDLING AND STORAGE 7.1. Precautions for Safe Handling Additional Hazards When Processed: Do not use in a confined area with minimal air exchange. Keep out of reach of children. Do not handle until all safety precautions have been read and understood. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Ground/bond container and receiving equipment. Use only non-sparking tools. Take precautionary measures against static discharge. Do not breathe dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Avoid release to the environment. Avoid contact with oxidizing agents (eg. chlorine, chromic acid etc.) Wear low static or properly grounded shoes. Use personal protective equipment (gloves, respirators, etc.) as required. To minimize the risk of ignition, determine applicable electrical classifications for the process using this product and select specific local exhaust ventilation equipment to avoid flammable vapor accumulation. Vapors may travel long distances along the ground or floor to an ignition source and flash back. Hygiene Measures: 7.2. Conditions for Safe Storage, Including Any Incompatibilities Technical Measures: Storage Conditions: Store in a well-ventilated place. Keep cool. Keep container tightly closed. Store away from acids. Store away from oxidizing agents. 7.3. Specific End Use(s) SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1. Control Parameters 8.2. Exposure Controls Appropriate Engineering |Use general dilution ventilation and/or local Controls |exhaust ventilation to control airborne exposures to |below relevant Exposure Limits and/or control |dust/fume/gas/mist/vapors/spray. If ventilation is |not adequate, use respiratory protection equipment. |Use explosion-proof ventilation equipment. Personal Protective Equipment| Materials for Protective | Clothing | Hand Protection |Select and use gloves and/or protective clothing |approved to relevant local standards to prevent skin |contact based on the results of an exposure |assessment. Selection should be based on use factors |such as exposure levels, concentration of the |substance or mixture, frequency and duration, |physical challenges such as temperature extremes, |and other use conditions. Consult with your glove |and/or protective clothing manufacturer for |selection of appropriate compatible |gloves/protective clothing. Gloves made from the |following material(s) are recommended: Neoprene. Eye Protection |Select and use eye/face protection to prevent |contact based on the results of an exposure |assessment. The following eye/face protection(s) are |recommended: Indirect Vented Goggles. Skin and Body Protection | Respiratory Protection |An exposure assessment may be needed to decide if a |respirator is required. If a respirator is needed, |use respirators as part of a full respiratory |protection program. Based on the results of the |exposure assessment, select from the following |respirator type(s) to reduce inhalation exposure: |Half facepiece or full facepiece air-purifying |respirator suitable for organic vapors and |particulates For questions about suitability for a |specific application, consult with your respirator |manufacturer. Thermal Hazard Protection | SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1. Information on Basic Physical and Chemical Properties Physical State |Liquid Appearance | Odor |Amber Liquid Hexane Odor Odor Threshold |No Data Available pH |Not Applicable Relative Evaporation Rate |1.90 Ether = 1 (butylacetate=1) | Melting Point |No Data Available Freezing Point | Boiling Point |148.00 ÂºF [Details: CONDITIONS: (hexane)] Flash Point |-7 Deg F [Test Method: Tagliabue Closed Cup] Auto-ignition Temperature | Decomposition Temperature |No Data Available Flammability (solid, gas) |Not Applicable |LEL 1.20 % volume |UEL 6.90 % volume Vapor Pressure |126.5000 mmHg [@ 68.0 ÂºF] Relative Vapor Density at 20 Â°C |2.97 [Ref Std: AIR=1] Relative Density | Specific Gravity |0.760 [Ref Std: WATER=1] Solubility |Slight (less than 10%) Partition coefficient: |No Data Available n-octanol/water | Viscosity |450 - 1,250 centipoise Lower Flammable Limit | Upper Flammable Limit | 9.2. Other Information Volatile Organic Compounds 585 g/l [Test Method: calculated SCAQMD rule 443.1] Volatile Organic Compounds 76.9 % weight [Test Method: calculated per CARB title 2] Percent volatile 79.4 % weight VOC Less H2O & Exempt Solvents 596 g/l [Test Method: calculated SCAQMD rule 443.1] SECTION 10: STABILITY AND REACTIVITY 10.1 Reactivity This material may be reactive with certain agents under certain conditions - see the remaining headings in this section. 10.2 Chemical Stability Stable. 10.3 Possibility of Hazardous Reactions Hazardous polymerization will not occur. 10.4 Conditions to Avoid Not determined 10.5 Incompatible Materials Strong oxidizing agents 10.6 Hazardous Decomposition Products Substance Condition Formaldehyde Not Specified Carbon monoxide Not Specified Carbon dioxide Not Specified Oxides of Sulfur Not Specified Toxic Vapor, Gas, Particulate Not Specified SECTION 11: TOXICOLOGICAL INFORMATION 11.1. Information on Toxicological Effects Acute Toxicity: The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be relevant to the material as a whole. Skin Corrosion/Irritation: Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness. Serious Eye Damage/Irritation: Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. Respiratory or Skin Sensitization: Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. May cause target organ effects after inhalation. Germ Cell Mutagenicity: Carcinogenicity: Ingredient C.A.S. No. Class Description Regulation METHYL ISOBUTYL KETONE 108-10-1 Grp. 2B: Possible human carc. International Agency for Research on Cancer Reproductive Toxicity: Contains a chemical or chemicals which can cause birth defects or other reproductive harm. Specific Target Organ Toxicity (Single Exposure): Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea, slowed reaction time, slurred speech, giddiness, and unconsciousness. Specific Target Organ Toxicity (Repeated Exposure): Peripheral Neuropathy: Signs/symptoms may include tingling or numbness of the extremities, incoordination, weakness of the hands and feet, tremors and muscle atrophy. Aspiration Hazard: Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. May cause target organ effects after ingestion. Chronic Symptoms: SECTION 12: ECOLOGICAL INFORMATION 12.1. Toxicity Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material and/or its components. Chemical fate information: Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material and/or its components. 12.2. Persistence and Degradability 12.3. Bioaccumulative Potential 12.4. Mobility in Soil 12.5. Other Adverse Effects SECTION 13: DISPOSAL CONSIDERATIONS 13.1. Waste treatment methods Waste Disposal Recommendations: Dispose of contents/ container in accordance with the local/regional/national/international regulations. Incinerate in a permitted waste incineration facility. Empty drums/barrels/containers used for transporting and handling hazardous chemicals (chemical substances/mixtures/preparations classified as Hazardous as per applicable regulations) shall be considered, stored, treated & disposed of as hazardous wastes unless otherwise defined by applicable waste regulations. Consult with the respective regulating authorities to determine the available treatment and disposal facilities. Additional Information: EPA Hazardous Waste Number (RCRA): D001 (Ignitable) SECTION 14: TRANSPORT INFORMATION 14.1 In Accordance with DOT Proper Shipping Name | Hazard Class | |<PICTOGRAM PHRASE> Identification Number| | Label Codes | | ERG Number | 14.2 In Accordance with IMDG Proper Shipping Name | Hazard Class | Identification Number| Label Codes | |<PICTOGRAM PHRASE> ntification Of The | | Substance/m | | EmS-No. (Fire) | | EmS-No. (Spillage) | | 14.3 In Accordance with IATA Proper Shipping Name | Identification Number| |<PICTOGRAM PHRASE> Hazard Class | | Label Codes | | ntification Of The | | Substance/m | | ERG Code (IATA) | SECTION 15: REGULATORY INFORMATION 15.1 US Federal Regulations Contact 3M for more information. SARA Section 311/312 Hazard Classes |Fire Hazard - Yes |Pressure Hazard - No |Reactivity Hazard - No |Immediate Hazard - Yes |Delayed Hazard - Yes Toxic Substances Control Act (TSCA) |The components of this product are in |compliance with the chemical notification |requirements of TSCA. Contact 3M for more |information. 15.2 US State Regulations California Proposition 65 Ingredient C.A.S. No. Classification METHYL ISOBUTYL KETONE 108-10-1 Carcinogen METHYL ALCOHOL 67-56-1 Developmental Toxin WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm. WARNING: This product contains a chemical known to the State of California to cause cancer. Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA): Ingredient C.A.S. No % by Wt HEXANE 110-54-3 Trade Secret 30 - 60 HEXANE (Hexane) 110-54-3 30 - 60 CALCIUM ZINC RESINATE 68334-35-0 1 - 5 (ZINC COMPOUNDS) Contact 3M for more information. SECTION 16: OTHER INFORMATION, INCLUDING DATE OF PREPARATION OR LAST REVISION Revision date | Other |This document has been prepared in accordance with the SDS Information |requirements of the OSHA Hazard Communication Standard 29 CFR |1910.1200. GHS Full Text Phrases: ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | Grainger disclaimer. The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application. 3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available directly from 3M.
The information contained in this SDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'SDS' shall be created or inferred by any statement in this 'SDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'SDS'. The user is responsible for full compliance.