Product Categories See All
Track Order Status
SDS Sheet 0066100Printer Friendly View
SECTION 1: IDENTIFICATION 1.1. Product Identifier Product Form: Aerosol. Product Name: 15 OZ SW L3 MOLY PTFE LUBE LB 12PK CAS No: Synonyms: 1.2. Intended Use of the Product Use of the substance/mixture: Lubricant 1.3. Name, Address, and Telephone of the Responsible Party Company : Sprayway, Inc. 1005 S. Westgate Drive Addison, IL 60101 United States Phone: General Assistance 1-630-628-3000 1.4. Emergency Telephone Number Emergency | 1-866-836-8855 (US) number |1-952-852-4646 (outside US) SECTION 2: HAZARDS IDENTIFICATION 2.1. Classification of the Substance or Mixture Classification (GHS-US) Flammable |Category 1 aerosols | Serious eye |Category 2 damage/eye | irritation | Sensitization,|Category 1 skin | Aspiration |Category 1 hazard | 2.2. Label Elements GHS-US Labeling Hazard Pictograms (GHS-US) |Flame |Health Hazard |Exclamation Mark Signal Word (GHS-US) |Danger Hazard Statements (GHS-US) |Extremely flammable aerosol. May be fatal if |swallowed and enters airways. May cause an allergic |skin reaction. Causes serious eye irritation. Precautionary Statements |Prevention: Keep away from heat/sparks/open (GHS-US) |flames/hot surfaces. - No smoking. Do not spray on |an open flame or other ignition source. Pressurized |container: Do not pierce or burn, even after use. |Avoid breathing gas. Wash thoroughly after handling. |Contaminated work clothing must not be allowed out |of the workplace. Wear protective gloves. Wear |eye/face protection. Response: If swallowed: |Immediately call a poison center/doctor. If on skin: |Wash with plenty of water. If in eyes: Rinse |cautiously with water for several minutes. Remove |contact lenses, if present and easy to do. Continue |rinsing. Specific treatment (see this label). Do NOT |induce vomiting. If skin irritation or rash occurs: |Get medical advice/attention. If eye irritation |persists: Get medical advice/attention. Wash |contaminated clothing before reuse. Collect |spillage. | |Storage: Store locked up. Protect from sunlight. Do |not expose to temperatures exceeding 50Â°C/122Â°F. | |Disposal: Dispose of contents/container in |accordance with |local/regional/national/international regulations. 2.3. Other Hazards Other Hazards Not Contributing to the Classification: None known. 2.4. Unknown Acute Toxicity (GHS-US) SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS 3.1. Substance Name |Product identifier |% |Classification | | |(GHS-US) | | | | | | | | | | | | | | | Full text of H-phrases: See Section 16 3.2. Mixture Name |Product identifier |% |Classification | | |(GHS-US) Distillates |64742-47-8 |20 - 40 | (Petroleum),Hydrotreated Light | | | Propane |74-98-6 |10 - 20 | Diethylene Glycol Monobutyl |112-34-5 |2.5 - 10| Ether | | | Pine Oil |8002-09-3 |2.5 - 10| Dimethyl Sulfoxide |67-68-5 |1 - 2.5 | Heavy Paraffinic Petroleum |64741-88-4 |0.1 - 1 | Distillates | | | Other components below | |40 - 60 | reportable levels | | | *Designates that a specific chemical identity and/or percentage of composition has been withheld as a trade secret. SECTION 4: FIRST AID MEASURES 4.1. Description of First Aid Measures First-aid Measures General: Take off all contaminated clothing immediately. Wash contaminated clothing before reuse. First-aid Measures After Inhalation: If symptoms develop move victim to fresh air. Get medical attention if symptoms persist. First-aid Measures After Skin Contact: In case of eczema or other skin disorders: Seek medical attention and take along these instructions. First-aid Measures After Eye Contact: Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if present and easy to do. First-aid Measures After Ingestion: Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs. 4.2. Most important symptoms and effects, both acute and delayed Symptoms/Injuries: May cause allergic skin reaction. Dermatitis. Aspiration may cause pulmonary edema and pneumonitis. Rash. Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. May cause drowsiness or dizziness. May cause an allergic skin reaction. Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: 4.3. Indication of Any Immediate Medical Attention and Special Treatment Needed Provide general supportive measures and treat symptomatically. Keep victim under observation. Symptoms may be delayed. SECTION 5: FIRE-FIGHTING MEASURES 5.1. Extinguishing Media Suitable Extinguishing Media: Alcohol resistant foam. Water fog. Dry chemical powder. Dry chemicals. Carbon dioxide (CO2). Unsuitable Extinguishing Media: Do not use water jet as an extinguisher, as this will spread the fire. 5.2. Special Hazards Arising From the Substance or Mixture Fire Hazard: Extremely flammable aerosol. Explosion Hazard: Reactivity: Contents under pressure. Pressurized container may explode when exposed to heat or flame. 5.3. Advice for Firefighters Precautionary Measures Fire: Use standard firefighting procedures and consider the hazards of other involved materials. Move containers from fire area if you can do so without risk. In the event of fire and/or explosion do not breathe fumes. Firefighting Instructions: Move containers from fire area if you can do so without risk. Cool containers exposed to heat with water spray and remove container, if no risk is involved. Containers should be cooled with water to prevent vapor pressure build up. For massive fire in cargo area, use unmanned hose holder or monitor nozzles, if possible. If not, withdraw and let fire burn out. Protection During Firefighting: Firefighters must use standard protective equipment including flame retardant coat, helmet with face shield, gloves, rubber boots, and in enclosed spaces, SCBA. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal Precautions, Protective Equipment and Emergency Procedures General Measures: 6.1.1. For Non-emergency Personnel Protective Equipment: Emergency Procedures: 6.1.2. For Emergency Responders Protective Equipment: Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of low areas. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Wear appropriate protective equipment and clothing during clean-up. Avoid breathing gas. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Ventilate closed spaces before entering them. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS. Emergency Procedures: 6.2. Environmental Precautions Avoid release to the environment. Inform appropriate managerial or supervisory personnel of all environmental releases. Prevent further leakage or spillage if safe to do so. Avoid discharge into drains, water courses or onto the ground. 6.3. Methods and Material for Containment and Cleaning Up For Containment: Refer to attached safety data sheets and/or instructions for use. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep combustibles (wood, paper, oil, etc.) away from spilled material. Stop leak if you can do so without risk. Move the cylinder to a safe and open area if the leak is irreparable. Methods for Cleaning Up: Use water spray to reduce vapors or divert vapor cloud drift. Isolate area until gas has dispersed. Prevent entry into waterways, sewer, basements or confined areas. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination. For waste disposal, see section 13 of the SDS. 6.4. Reference to Other Sections See heading 8, Exposure Controls and Personal Protection. SECTION 7: HANDLING AND STORAGE 7.1. Precautions for Safe Handling Additional Hazards When Processed: Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or expose containers to heat, flame, sparks, or other sources of ignition. All equipment used when handling the product must be grounded. Use non-sparking tools and explosion-proof equipment. Do not re-use empty containers. Do not get in eyes, on skin, on clothing. Avoid breathing gas. Avoid contact with eyes, skin, and clothing. Avoid prolonged or repeated contact with skin. Avoid prolonged exposure. Use only in well-ventilated areas. Wear appropriate personal protective equipment. Wash hands thoroughly after handling. Avoid release to the environment. Observe good industrial hygiene practices. Hygiene Measures: Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Contaminated work clothing should not be allowed out of the workplace. 7.2. Conditions for Safe Storage, Including Any Incompatibilities Technical Measures: Storage Conditions: Level 3 Aerosol. Store locked up. Pressurized container. Protect from sunlight and do not expose to temperatures exceeding 50Â°C/122 Â°F. Do not puncture, incinerate or crush. Do not handle or store near an open flame, heat or other sources of ignition. This material can accumulate static charge which may cause spark and become an ignition source. Store in a well-ventilated place. Refrigeration recommended. Store away from incompatible materials (see Section 10 of the SDS). 7.3. Specific End Use(s) SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1. Control Parameters 8.2. Exposure Controls Appropriate Engineering |Explosion-proof general and local exhaust Controls |ventilation. Good general ventilation (typically 10 |air changes per hour) should be used. Ventilation |rates should be matched to conditions. If |applicable, use process enclosures, local exhaust |ventilation, or other engineering controls to |maintain airborne levels below recommended exposure |limits. If exposure limits have not been |established, maintain airborne levels to an |acceptable level. Provide eyewash station. Personal Protective Equipment| Materials for Protective | Clothing | Hand Protection |Wear appropriate chemical resistant gloves. Eye Protection |Face shield is recommended. Wear safety glasses with |side shields (or goggles). Skin and Body Protection |Wear appropriate chemical resistant clothing. Use of |an impervious apron is recommended. Respiratory Protection |If permissible levels are exceeded use NIOSH |mechanical filter / organic vapor cartridge or an |air-supplied respirator. Thermal Hazard Protection |Wear appropriate thermal protective clothing, when |necessary. SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1. Information on Basic Physical and Chemical Properties Physical State |Gas. Appearance | Odor |Pine Odor Threshold |Not available. pH |Not available. Relative Evaporation Rate |Not available. (butylacetate=1) | Melting Point |Not available. Freezing Point |Not available. Boiling Point |145.8 Â°F (63.22 Â°C) estimated Flash Point |-156.0 Â°F (-104.4 Â°C) propellant estimated Auto-ignition Temperature |421 Â°F (216.11 Â°C) estimated Decomposition Temperature |Not available Flammability (solid, gas) |Not available Vapor Pressure |26.46 psig @70F estimated Relative Vapor Density at 20 Â°C |Not available Relative Density |Not available. Specific Gravity |0.83 - 0.87 estimated Solubility |Not available. Partition coefficient: |Not available. n-octanol/water | Viscosity |Not available. Lower Flammable Limit |Not available. Upper Flammable Limit |Not available. 9.2. Other Information SECTION 10: STABILITY AND REACTIVITY 10.1 Reactivity The product is stable and non-reactive under normal conditions of use, storage and transport. 10.2 Chemical Stability Material is stable under normal conditions. 10.3 Possibility of Hazardous Reactions No dangerous reaction known under conditions of normal use. Hazardous polymerization does not occur. 10.4 Conditions to Avoid Avoid heat, sparks, open flames and other ignition sources. Avoid temperatures exceeding the flash point. Contact with incompatible materials. 10.5 Incompatible Materials Strong oxidizing agents. 10.6 Hazardous Decomposition Products No hazardous decomposition products are known. SECTION 11: TOXICOLOGICAL INFORMATION 11.1. Information on Toxicological Effects Acute Toxicity: May be fatal if swallowed and enters airways. May cause an allergic skin reaction. Expected to be a low hazard for usual industrial or commercial handling by trained personnel. Skin Corrosion/Irritation: Causes mild skin irritation. Serious Eye Damage/Irritation: Causes serious eye irritation. Respiratory or Skin Sensitization: Not a respiratory sensitizer. May cause an allergic skin reaction. Germ Cell Mutagenicity: Suspected of causing genetic defects. Carcinogenicity: Suspected of causing cancer. Reproductive Toxicity: This product is not expected to cause reproductive or developmental effects. Specific Target Organ Toxicity (Single Exposure): Not available. Specific Target Organ Toxicity (Repeated Exposure): Not available. Aspiration Hazard: May be fatal if swallowed and enters airways. Symptoms/Injuries After Inhalation: Narcotic effects. Prolonged inhalation may be harmful. Symptoms/Injuries After Skin Contact: Causes mild skin irritation. May cause an allergic skin reaction. Symptoms/Injuries After Eye Contact: Causes serious eye irritation. Symptoms/Injuries After Ingestion: Droplets of the product aspirated into the lungs through ingestion or vomiting may cause a serious chemical pneumonia. Smallest quantities reaching the lungs through swallowing or subsequent vomiting may result in lung edema or pneumonia. Chronic Symptoms: Prolonged inhalation may be harmful. SECTION 12: ECOLOGICAL INFORMATION 12.1. Toxicity Toxic to aquatic life with long lasting effects. Components Species Test Results Diethylene Glycol Monobutyl Ether (CAS 112-34-5) Aquatic Fish LC50 Bluegill (Lepomis macrochirus) 1300 mg/l, 96 hours Dimethyl Sulfoxide (CAS 67-68-5) Aquatic Fish LC50 Rainbow trout,donaldson trout 33000 - 37000 mg/l, 96 hours (Oncorhynchus mykiss) Distillates (Petroleum), Hydrotreated Light (CAS 64742-47-8) Aquatic Fish LC50 Rainbow trout,donaldson trout 2.9 mg/l, 96 hours (Oncorhynchus mykiss) Heavy Paraffinic Petroleum Distillates (CAS 64741-88-4) Aquatic Crustacea EC50 Daphnia 1000.0001 mg/L, 48 Hours Fish LC50 Fish 5001, 96 Hours 12.2. Persistence and Degradability No data is available on the degradability of this product. 12.3. Bioaccumulative Potential No data available. Partition coefficient n-octanol / water (log Kow) Diethylene Glycol Monobutyl Ether 0.56 Dimethyl Sulfoxide -2.03 12.4. Mobility in Soil No data available. 12.5. Other Adverse Effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component. SECTION 13: DISPOSAL CONSIDERATIONS 13.1. Waste treatment methods Waste Disposal Recommendations: Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see: Disposal instructions). Additional Information: SECTION 14: TRANSPORT INFORMATION 14.1 In Accordance with DOT Proper Shipping Name |Aerosols, flammable Hazard Class |2.1 |[pic] Identification Number|UN1950 | Label Codes |2.1 | ERG Number | 14.2 In Accordance with IMDG Proper Shipping Name |AEROSOLS Hazard Class |2.1 Identification Number|UN1950 Label Codes |2.1 |<PICTOGRAM PHRASE> ntification Of The | |[pic] Substance/m | | EmS-No. (Fire) | | EmS-No. (Spillage) | | 14.3 In Accordance with IATA Proper Shipping Name |Aerosols, flammable Identification Number|UN1950 |<PICTOGRAM PHRASE> [pic] Hazard Class |2.1 | Label Codes | | ntification Of The | | Substance/m | | ERG Code (IATA) |10L SECTION 15: REGULATORY INFORMATION 15.1 US Federal Regulations <COMPONENT> This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200. All components are on the U.S. EPA TSCA Inventory List. SARA Section 311/312 Hazard Classes |Immediate Hazard - Yes |Delayed Hazard - No |Fire Hazard - Yes |Pressure Hazard - No |Reactivity Hazard - No Toxic Substances Control Act (TSCA) |Not regulated. 15.2 US State Regulations <COMPONENT> US. Massachusetts RTK - Substance List Propane (CAS 74-98-6) US. New Jersey Worker and Community Right-to-Know Act Dimethyl Sulfoxide (CAS 67-68-5) Pine Oil (CAS 8002-09-3) Propane (CAS 74-98-6) US. Pennsylvania Worker and Community Right-to-Know Law Propane (CAS 74-98-6) US. Rhode Island RTK Propane (CAS 74-98-6) US. California Proposition 65 California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain any chemicals currently listed as carcinogens or reproductive toxins. SECTION 16: OTHER INFORMATION, INCLUDING DATE OF PREPARATION OR LAST REVISION Revision date |04-14-2015 Other |This document has been prepared in accordance with the SDS Information |requirements of the OSHA Hazard Communication Standard 29 CFR |1910.1200. GHS Full Text Phrases: ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | Grainger disclaimer.
The information contained in this SDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'SDS' shall be created or inferred by any statement in this 'SDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'SDS'. The user is responsible for full compliance.