Register Now    |    Login

National Distributor of Quality Maintenance Supplies Since 1958

1-800-558-2808

Track Order Status
Order No:
Zip Code:

MSDS Sheet 0066000

Printer Friendly View
        

            7497210-00 L/M 11310 & 11309 ULTR LUBE (487210)
                 MATERIAL SAFETY DATA BULLETIN

1. PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME:  L/M 11310 & 11309 ULTRA LUBE (487210)
SUPPLIER: EXXON MOBIL CORPORATION
      3225 GALLOWS ROAD
      FAIRFAX,  VA  22037
24 - Hour Health and Safety Emergency (call collect):    609-737-4411
24 - Hour Transportation Emergency (Primary) CHEMTREC:   800-424-9300
                                           (Secondary)   281-834-3296

Product and Technical Information:
Lubricants and Specialties: 800-662-4525    800-443-9966
Fuels Products:  800-947-9147
MSDS Fax on Demand: 613-228-1467
MSDS Internet Website : http://emmsds.ihssolutions.com/

2.  COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Names and Synonyms: Base Oil and Additives
Globally Reportable MSDS Ingredients;    None
See Section 8 for exposure limits  (if applicable).

3. HAZARDS IDENTIFICATION

This product is considered hazardous according to regulatory guidelines
(See Section 15).
EMERGENCY OVERVIEW: Black Grease. DOT ERG No.:  NA
POTENTIAL HEALTH EFFECTS: Causes eye and skin irritation. Excessive exposure
may result in respirator irritation.
For further health effects/toxicological data, see Section 11.

4. FIRST AID MEASURES

EYE CONTACT: Flush thoroughly with water for at least 15 minutes. Get immediate
medical assistance. If medical assistance is not immediately available, flush
an additional 15 minutes. In still local anesthetic eye drops to facilitate
irrigation, if available.
SKIN CONTACT: Wash contact area with soap and water. Remove contaminated
clothing. Wash carefully behind ears, under nails and in skin folds. Get
medical assistance. For those providing assistance, avoid further skin contact
to yourself and others. Wear impervious gloves. Launder contaminated clothing
separately before reuse. Discard contaminated clothing articles that cannot be
laundered. INJECTION INJURY WARNING: if product is injected into or under the
skin, or into any part of the body, regardless of the appearance of the wound
or its size, the individual should be evaluated immediately by a physician as a
surgical emergency.
Even though initial symptoms from high pressure injection may be minimal or
absent, early surgical treatment within the first few hours may significantly
reduce the ultimate extent of injury.
INHALATION: Not expected to be a problem. However, if respiratory irritation,
dizziness, nausea, or unconsciousness occurs due to excessive vapor or mist
exposure, seek immediate medical assistance. If breathing has stopped, assist
ventilation with a mechanical device or mouth-to-mouth resuscitation.
INGESTION: Seek medical advice. Do not induce vomiting.

5. FIRE-FIGHTING MEASURES

EXTINGUISHING MEDIA: Carbon dioxide, foam, dry chemical and water fog.
SPECIAL FIRE FIGHTING PROCEDURES: Water or foam may cause frothing. Use water
to keep fire exposed containers cool. Water spray may be used to flush spills
away from exposure. Prevent runoff from fire control or dilution from entering
streams, sewers, or drinking water supply.
SPECIAL PROTECTIVE EQUIPMENT: Product health hazards may require personal
protective equipment in addition to that normally worn (see MSDS sections on
special protection information and special precautions). For fires in enclosed
areas, fire fighters must use self-contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARDS:  None.
COMBUSTION PRODUCTS: Fumes, smoke, carbon monoxide, sulfur oxides, aldehydes
and other decomposition products, in the case of incomplete combustion.
Flash Point  C (F):  > 180 (356) (Estimated For Oil, ASTM D-92 (COC).
Flammable Limits (approx. % vol. in air) - LEL: NE,      UEL:  NE
NFPA HAZARD ID:  Health: 2,  Flammability: 1,  Reactivity: 0

6. ACCIDENTAL RELEASE MEASURES

NOTIFICATION PROCEDURES: Report spills/releases as required to appropriate
authorities. U.S. Coast Guard and EPA regulations require immediate reporting
of spills/releases that could reach any waterway including intermittent dry
creeks. Report spill/release to Coast Guard National Response Center tool free
number (800) 424-8802. In case of accident or road spill notify CHEMTREC (800)
424-9300.
PROCEDURES IF MATERIAL IS RELEASED OR SPILLED:
      LAND SPILL: Shut off source taking normal safety precautions.
      Take measures to minimize the effects on ground water.
      Recover by pumping or contain spilled material with sand or other
      suitable absorbent and remove mechanically into containers.
      If necessary, dispose of absorbed residues as directed in Section 13.
      WATER SPILL: Confine the spill immediately with booms.
      Warn other ships in the vicinity. Notify port and other relevant
      authorities. Remove from the surface by skimming or with suitable
      absorbents. If permitted by regulatory authorities the use of suitable
      dispersants should be considered where recommended in local oil spill
      procedures.
      ENVIRONMENTAL PRECAUTIONS: Prevent material from
      entering sewers, water sources or low lying areas: advise the relevant
      authorities if it has, or if it contaminates soil/vegetation.
      PERSONAL PRECAUTIONS:   See Section 8

7. HANDLING AND STORAGE

HANDLING:  High pressure injection under the skin may occur due to the
            rupture of pressurized lines. Always seek medical attention.
            Avoid contact with eyes. Avoid contact with skin. See Section
            8 for additional personal protection advice when handling this
            product.
STORAGE:    Keep containers closed when not in use. Do not store in open
            or unlabeled containers. Store away from strong oxidizing
            agents and combustible materials. Do not store near heat,
            sparks, flame or strong oxidants.
SPECIAL PRECAUTIONS: Prevent small spills and leakages to avoid slip
            hazard.
EMPTY CONTAINER WARNING: Empty containers retain residue (liquid
            And/or vapor) and can be dangerous. DO NOT PRESSURIZE,
            CUT, WELD, BRAZE, SOLDER, DRILL, GRIND OR
            EXPOSE SUCH CONTAINERS TO HEAT, FLAME,
            SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES
            OF IGNITION. THEY MAY EXPLODE AND CAUSE
            INJURY OR DEATH.  Do not attempt to refill or clean
            container since residue is difficult to remove. Empty drums
            should be completely drained, properly bunged and promptly
            returned to a drum reconditioner. All containers should be
            disposed of in an environmentally safe manner and in
            accordance with governmental regulations.

8. EXPOSURE CONTROLS/PERSONAL PROTECTION

OCCUPATIONAL EXPOSURE LIMITS:
This product does not contain any components which have recognized exposure
limits.
VENTILATION: Use adequate ventilation.
RESPIRATORY PROTECTION: No special requirements under ordinary conditions of
use and with adequate ventilation.
EYE PROTECTION: Chemical type goggles must be worn.
SKIN PROTECTION: Protective clothing such as uniforms, coveralls or lab coats
should be worn. Impervious gloves should be worn. Chemical resistant apron
should be worn when handling bulk quantities.

9. PHYSICAL AND CHEMICAL PROPERTIES

Typical physical properties are given below. Consult Product Data Sheet for
specific details.
APPEARANCE:  Grease
COLOR:  Black
ODOR:   Mild
ODOR THRESHOLD - ppm:  NE
pH:  NA
BOILING POINT C(F):   NE
DROP POINT  C (F):  NE
FLASH POINT C (F):  > 180 (356) (ESTIMATED FOR OIL, ASTM D-92 (COC)
FLAMMABILITY (solids):  NE
AUTO FLAMMABILITY C (F):  NA
EXPLOSIVE PROPERTIES:  NA
OXIDIZING PROPERTIES:  NA
VAPOR PRESSURE-mmHg  20 C: < 0.1
VAPOR DENSITY:  NE
EVAPORATION RATE:  NE
RELATIVE DENSITY,  15/4 C: 0.912
SOLUBILITY IN WATER:  Negligible
PARTITION COEFFICIENT:  > 3.5
VISCOSITY AT 40 C,  cSt:  > 20.0
VISCOSITY AT 100 C, cSt:  NE
FOUR POINT C (F):  NE
FREEZING POINT  C (F);  NE
VOLATILE ORGANIC COMPOUND:  NE
NOTE: MOST PHYSICAL PROPERTIES FOR  OIL COMPONENT.
DMSO EXTRACT, IP-346 (WT%): <3, for mineral oil only
NA=NOT APPLICABLE  NE=NOT ESTABLISHED D=DECOMPOSES
FOR FURTHER TECHNICAL INFORMATION, CONTACT YOUR MARKETING REPRESENTATIVE.

10. STABILITY AND REACTIVITY

STABILITY  (THERMAL, LIGHT, ETC.): Stable
CONDITIONS TO AVOID: Extreme heat and high energy sources of ignition.
INCOMPATIBILITY (MATERIALS TO AVOID):  Strong oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS: Product does not decompose at ambient
temperatures.
HAZARDOUS POLYMERIZATION:  Will not occur.

11. TOXICOLOGICAL DATA

                 ----  ACUTE TOXICOLOGY ----
ORAL TOXICITY (RATS): Practically non-toxic (LD50: greater than 2000 mg/kg). ---
 Based on testing of similar products and/or the components.
DERMAL TOXICITY (RABBITS): Practically non-toxic  (LD50: greater than  2000
mg/kg).  --- Based on testing of similar products and/or the components.
INHALATION TOXICITY  (RATS): Practically non-toxic  (LC50: greater than 5
mg/L). --- Based on testing of similar products and/or the components.
EYE IRRITATION  (RABBITS): Strong irritant.  (Draize score:  greater than 35
but 55 or less).  --- Based on testing of similar products  and/or the
components.
SKIN IRRITATION  (RABBITS):  Strong irritant.  (Primary Irritation Index:
5 or greater but less than 6).  --- Based on testing of similar products and/or
the components.
OTHER ACUTE TOXICITY DATA:  Although an acute inhalation study was not
performed with this product, a variety of mineral oils and synthetic base oils,
such as those in this product have been tested. These samples had virtually no
effect other than a nonspecific inflammatory response in the lung to the
aerosolized mineral oil. The presence of additives in other tested formulations
(in approximately the same amounts as in the present  formulation) did not
alter the observed effects.
                 SUB CHRONIC TOXICOLOGY (SUMMARY)
No significant adverse effects were found in studies using repeated dermal
applications of similar formulations to the skin of laboratory animals for 13
weeks at doses significantly higher than those expected during normal
industrial exposure. The animals were evaluated extensively for effects of
exposure  (hematology, serum chemistry, urinalysis, organ weights, microscopic
examination of tissue etc.).
                 REPRODUCTIVE TOXICOLOGY (SUMMARY)
No teratogenic effects would be expected from dermal exposure, based on
laboratory developmental toxicity studies of major components in this
formulation and/or materials of similar composition.
                 CHRONIC TOXICOLOGY (SUMMARY)
Repeated and/or prolonged exposure may cause irritation to the skin, eyes or
respiratory tract. For mineral base oils: Base oils in this product are
severely solvent refined and/or severely hydro treated. Chronic mouse skin
painting studies of severely treated oils showed no evidence of carcinogenic
effects. These results are confirmed on a continuing basis using various
screening methods such as Modified Ames Test, IP-346, and/or other analytical
methods. For synthetic base oils: The base oils in this product have been
tested in the Ames assay and other tests of mutagenicity with negative results.
These base oils are not expected to be carcinogenic with chronic dermal
exposures.
                 SENSITIZATION (SUMMARY)
Not expected to be sensitizing based on tests of this product, components, or
similar products.

12. ECOLOGICAL INFORMATION

ENVIRONMENTAL FATE AND EFFECTS:
This environmental assessment was conducted using information on the individual
components as no test data was available for this specific formulation.
ECOTOXICITY: The major components in the formulation show no aquatic toxicity
at 1000 mg/L loading, therefore long-term adverse effects in the aquatic
environment are not expected.
MOBILITY: Not established.
PERSISTENCE AND DEGRADABILITY: This product is expected to be inherently
biodegradable, as the principal components have been shown to degrade at slow
to moderate rates.
BIO ACCUMULATIVE POTENTIAL:  Not established.

13. DISPOSAL CONSIDERATIONS

WASTE DISPOSAL: Product is suitable for burning in an enclosed, controlled
burner for fuel value. Such burning may be limited pursuant to the Resource
Conservation and Recovery Act. In addition, the product is suitable for
processing by an approved  recycling facility or can be disposed of at an
appropriate government waste disposal facility. Use of these methods is subject
to user compliance with applicable laws and regulations and consideration of
product characteristics at time of disposal.
RCRA INFORMATION: The unused product, in our opinion, is not specifically
listed by the EPA as a hazardous waste (40 CFR, Part 261D), nor is it
formulated to contain materials which are listed hazardous wastes. It does not
exhibit the hazardous characteristics of ignitability, corrosively, or
reactivity. The unused product is not formulated with substances covered by the
Toxicity Characteristic Leaching Procedure (TCLP). However, used product may be
regulated.

14. TRANSPORT INFORMATION

USA DOT: NOT REGULATED BY USA DOT.
RID/ADR: NOT REGULATED BY RID/ADR
IMO: NOT REGULATED BY IMO.
IATA: NOT REGULATED BY IATA.

15. REGULATORY INFORMATION

US OSHA HAZARD COMMUNICATION STANDARD: Product assessed in accordance with OSHA
29 CFR 1910.1200 and determined to be hazardous.
EU Labeling: Product is dangerous ad defined by the European Union.
      Dangerous Substances/Preparations Directives.
Symbol: Xi  Irritant.
Risk Phrases (s): R36/38.
      Irritating to eyes and skin.
Safety Phrase (s);  S24/25-36.
      Avoid contact with skin and eyes. Wear suitable protective clothing.
Contains: Zinc Dithiophosphate
Governmental Inventory Status: All components comply with TSCA.
U.S. Superfund Amendments and Reauthorization Act (SARA) Title III:
      This product contains no "EXTREMELY HAZARDOUS SUBSTANCES".
      SARA (311/312) REPORTABLE HAZARD CATEGORIES:
      ACUTE
This product contains no chemicals subject to the supplier notification
requirements of SARA (313) toxic release program.
The following product ingredients are cited on the lists below:
CHEMICAL NAME                       CAS NUMBER      LIST CITATIONS
Lithium-Soap Thickener (5.65%)       7620-77-1         22

                           REGULATORY LISTS SEARCHED
1=ACGIH ALL   6=IARC  1          11=TSCA 4     16=CA P65 CARC    21=LA RTK
2=ACGIH A1    7=IARC  2A         12=TSCA 5a2   17=CA P65 REPRO   22=MI 293
3=ACGIH A2    8=IARC  2B         13=TSCA 5e    18=CA RTK         23=MN RTK
4=NTP   CARC  9=OSHA  CARC       14=TSCA 6     19=FL RTK         24=NJ RTK
5=NTP   SUS   10=OSHA Z          15=TSCA 12b   20=IL RTK         25=PA RTK
                                                                 26=RI RTK
Code key:  CARC=Carcinogen: SUS=Suspected Carcinogen:
REPRO=Reproductive

16. OTHER INFORMATION

USE:  GREASE
NOTE:  PRODUCTS OF EXXON MOBIL CORPORATION AND ITS AFFILIATED COMPANIES ARE NOT
FORMULATED TO CONTAIN  PCBS.
Health studies have shown that many hydrocarbons pose potential human health
risks which may vary from person to person. Information provided on this MSDS
reflects intended use. This product should not be used for other applications.
In any case, the following advice should be considered:
Precautionary Label Text:
CONTAINS ZINC DITHIOPHOSPHATE
WARNING! CAUSES EYE AND SKIN IRRITATION. EXCESSIVE EXPOSURE MAY RESULT IN
RESPIRATORY IRRITATION.

Avoid contact with eyes, skin, and clothing. Keep container closed.
FIRST AID: In case of contact, immediately flush eyes with plenty of water for
at least 15 minutes. Wash skin with soap and plenty of water.
Remove contaminated clothing.
Refer to product Material Safety Data Sheet for further safety and health
information.

For Internal Use Only: MHC: 1* 1* 1* 3* 3*, MPPEC: D, TRN:
7487210-00, CMCS97:  97R841, REQ: PS+C, SAFE USE:  L
EHS Approval Date: 030CT2001

Legally required information is given in accordance with applicable Information
given herein is offered in good faith as accurate, but without guarantee.
Conditions of use and suitability of the product for particular uses are beyond
our control: all risks of use of the product are therefore assumed by the user
and WE EXPRESSLY DISCLAIM ALL WARRANTIES OF EVERY KIND AND NATURE, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN RESPECT
TO THE USE OR SUITABILITY OF THE PRODUCT.
Nothing is intended as a recommendation for uses which infringe valid patents
or as extending and license under valid patents. Appropriate warnings and safe
handling procedures should be provided to handlers and users. Use or
retransmission of the information contained herein in any other format than the
format as presented is strictly prohibited. Mobil neither represents nor
warrants that the format, content or product formulas contained in this
document comply with the laws of any other country except the United States of
America.

Copyright 1996 Mobil Corporation, All rights reserved.

    

The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'MSDS' shall be created or inferred by any statement in this 'MSDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'MSDS'. The user is responsible for full compliance.

Feedback