Product Categories See All
Track Order Status
SDS Sheet 0065990Printer Friendly View
SECTION 1: IDENTIFICATION 1.1. Product Identifier Product Form: Product Name: Corrosion Stop CAS No: Synonyms: 1.2. Intended Use of the Product Use of the substance/mixture: Water resistant spray 1.3. Name, Address, and Telephone of the Responsible Party Company: The Blaster Corp 8500 Sweet Valley Dr Valley View, OH 44125 Phone: (216)-901-5800 1.4. Emergency Telephone Number Emergency |Chemtrec (800) 424-9300 number | SECTION 2: HAZARDS IDENTIFICATION 2.1. Classification of the Substance or Mixture Classification (GHS-US) Flammable |Category 1 Aerosols | Gases under |Liquefied Gas pressure | Skin |Category 2, Irritation | Specific |Category 3 target organ |Central toxicity, |nervous single |system, exposure | Aspiration |Category 1 hazard | Acute aquatic |Category 1 toxicity | Chronic |Category 1 aquatic | toxicity | 2.2. Label Elements GHS-US Labeling Hazard Pictograms (GHS-US) |Flame |Health Hazard |Environment |Exclamation Mark |Gas Cylinder Hazard Statements (GHS-US) |H222 Extremely flammable aerosol |H229 Pressurized container: may burst if heated |H280 Contains gas under pressure, may burst if |heated |H335 May cause respiratory irritation |H336 May cause drowsiness |H304 May be fatal if swallowed and enters airways |H315 Causes Skin irritation |H319 Causes serious eye irritation. |H400 Very toxic to aquatic life |H410 Very toxic to aquatic life with lasting effects Precautionary Statements |P210 Keep away from heat, hot surfaces, sparks, open (GHS-US) |flames, and other ignition sources. No smoking. |P251 Pressurized container: Do not pierce or burn, |even after use |P261 Avoid breathing dust/fume/gas/mist vapors/spray | |P264 Wash...thoroughly after handling. |P271 Use only outdoors or in a well-ventilated area. | |P280 Wear protective gloves/protective clothing/eye |protection/face protection. |P301+P310 If Swallowed: Immediately call a poison |center or doctor |P304+P340 If Inhaled: Remove person to fresh air and |keep comfortable for breathing. |P332+P352 If skin irritation occurs: wash with |plenty of water and soap. |P403+P233 Store in well ventilated place Keep |container tightly closed. |P410+P412 Protect from sunlight. Don not expose to |temperatures exceeding 50Â°C/122Â°F |P501 Dispose of contents/container in accordance |with local/regional regulations. 2.3. Other Hazards Other Hazards Not Contributing to the Classification: 2.4. Unknown Acute Toxicity (GHS-US) SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS 3.1. Substance Name |Product identifier |% |Classification | | |(GHS-US) | | | | | | | | | | | | | | | Full text of H-phrases: See Section 16 3.2. Mixture Name |Product identifier |% |Classification | | |(GHS-US) Acetone |67-64-1 |20-25 | n-Heptane |142-82-5 |25-30 | Toluene |108-88-3 |0-2 | Petrolatum |8009-03-8 |25-35 | Liquefied Petroleum Gas |68476-86-8 |15-25 | SECTION 4: FIRST AID MEASURES 4.1. Description of First Aid Measures First-aid Measures General: First-aid Measures After Inhalation: Remove exposed individual to fresh air, protecting yourself. Restore breathing if necessary. Contact a physician. First-aid Measures After Skin Contact: Wash with soap and water. Remove any contaminated clothing and launder before reusing. If irritation persists, seek medical attention. First-aid Measures After Eye Contact: Flush with warm water for 15 minutes. Seek medical attention. First-aid Measures After Ingestion: Seek medical attention. If individual is drowsy or unconscious, do not give anything by mouth; place individual on the left side with the head down. Contact a physician, medical facility, or poison control center for advice about whether to induce vomiting. If possible, do not leave individual unattended. 4.2. Most important symptoms and effects, both acute and delayed Symptoms/Injuries: Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: 4.3. Indication of Any Immediate Medical Attention and Special Treatment Needed SECTION 5: FIRE-FIGHTING MEASURES 5.1. Extinguishing Media Suitable Extinguishing Media: Dry chemical, carbon dioxide, halon, or foam is recommended. Water spray may be used to cool containers or structures. Halon may decompose into toxic materials and carbon dioxide will displace oxygen, take proper precautions when using these materials. Unsuitable Extinguishing Media: 5.2. Special Hazards Arising From the Substance or Mixture Fire Hazard: Explosion Hazard: This material may be ignited by extreme heat, sparks, flames or other ignition sources (static electricity). Vapors are heavier than air and will collect in low areas (sewers) or travel considerable distances. If containers are not cooled in a fire, they may rupture and ignite. Reactivity: 5.3. Advice for Firefighters Precautionary Measures Fire: Firefighting Instructions: At elevated temperatures (over 130F) aerosol container may burst, vent or rupture; use equipment or shielding to protect personnel. Cooling exposed containers with streams of water may be helpful. Emergency responders should wear self-contained breathing apparatus. Wear other protective gear as conditions warrant. Keep unauthorized people out and try to contain spills or leaks if it can be done safely. Material will float on water, avoid spreading the fire. Protection During Firefighting: SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal Precautions, Protective Equipment and Emergency Procedures General Measures: 6.1.1. For Non-emergency Personnel Protective Equipment: Emergency Procedures: 6.1.2. For Emergency Responders Protective Equipment: Emergency Procedures: 6.2. Environmental Precautions 6.3. Methods and Material for Containment and Cleaning Up For Containment: Contain spill with dikes of soil or nonflammable absorbent to minimize contaminated area. Avoid run-off into storm sewers and ditches leading to waterways. If required, notify state and local authorities. Place leaking containers in well-ventilated area. Methods for Cleaning Up: Clean up small spills by using a nonflammable absorbent or flushing sparingly with water. Contain larger spills with nonflammable diking or absorbent. Clean up by vacuuming or sweeping. Keep unnecessary people away; isolate hazard area and deny entry. Stay upwind; keep out of low areas. Assess the spill situation, as the spill may not evolve large amounts of hazardous airborne contaminants in many outdoor spill situations. It may be advisable in some cases to simply monitor the situation until spilled product is removed. 6.4. Reference to Other Sections See heading 8, Exposure Controls and Personal Protection. SECTION 7: HANDLING AND STORAGE 7.1. Precautions for Safe Handling Additional Hazards When Processed: Store below 120Â°F in cool, dry area, out of direct sunlight and away from strong oxidizers. Do not puncture or burst. Use in accordance with good work place practices. Use with adequate ventilation. Keep containers closed when not in use. Always open containers slowly to allow any excess pressure to vent. Avoid breathing vapor. Avoid contact with eyes, skin or clothing. Wash thoroughly with soap and water after handling. Decontaminate soiled clothing thoroughly before re-use. Destroy contaminated leather Clothing. Empty containers may contain residues from the product. Treat empty containers with the same precautions as the material last contained. Do not cut, weld or apply heat to empty containers Do not incinerate Hygiene Measures: 7.2. Conditions for Safe Storage, Including Any Incompatibilities Technical Measures: Storage Conditions: Store in a cool, dry area, away form heat or direct sunlight. Keep containers closed when not in use. Do not store with incompatible materials 7.3. Specific End Use(s) SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1. Control Parameters 8.2. Exposure Controls Appropriate Engineering |General or dilution ventilation is frequently Controls |sufficient as the sole means of controlling employee |exposure. Local ventilation is usually preferred. |Use a NIOSH approved respirator if ventilation is |not adequate to maintain exposures below TLV levels. Personal Protective Equipment|Use synthetic gloves if necessary to prevent |excessive skin contact. Do not wear contacts and |always use ANSI approved safety glasses or splash |shield. Materials for Protective | Clothing | Hand Protection | Eye Protection |Eye wash station and emergency showers should be |available. Skin and Body Protection | Respiratory Protection |Use adequate ventilation to maintain exposure |limits. If the exposure limits of the products or |any of its components is exceeded, an approved |organic vapor mask should be used (consult your |safety equipment supplier). Above exposure levels an |approved self-contained breathing apparatus or |airline respirator with full face-piece is required. Thermal Hazard Protection | SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1. Information on Basic Physical and Chemical Properties Physical State | Appearance |Clear mist as dispensed from aerosol can Odor |dispensed Odor Threshold | pH | Relative Evaporation Rate |Ether = 1 Slower (butylacetate=1) | Melting Point | Freezing Point | Boiling Point |NA Flash Point |Flash point of liquid portion < 30Â°F Auto-ignition Temperature | Decomposition Temperature | Flammability (solid, gas) | Vapor Pressure | Relative Vapor Density at 20 Â°C | Relative Density | Specific Gravity |<1 Solubility |Negligible Partition coefficient: | n-octanol/water | Viscosity | Lower Flammable Limit |No Information Upper Flammable Limit |No Information 9.2. Other Information SECTION 10: STABILITY AND REACTIVITY 10.1 Reactivity 10.2 Chemical Stability Stable 10.3 Possibility of Hazardous Reactions Will not occur 10.4 Conditions to Avoid Heat, spark, and open flame 10.5 Incompatible Materials Strong-Oxidizing Agents. 10.6 Hazardous Decomposition Products Combustion will produce Carbon Monoxide, Carbon Dioxide and hydrocarbons.. SECTION 11: TOXICOLOGICAL INFORMATION 11.1. Information on Toxicological Effects Acute Toxicity: Skin Corrosion/Irritation: Serious Eye Damage/Irritation: Respiratory or Skin Sensitization: Germ Cell Mutagenicity: Carcinogenicity: Exposure of rats and mice to toluene at concentrations ranging from 120-1200 ppm for two years did not demonstrate evidence of carcinogenicity. Toluene has not been listed as a carcinogen by IARC. Reproductive Toxicity: No evidence of developmental toxicity was found in pregnant laboratory animals (rats and mice) exposed to high vapor concentrations of unleaded gasoline and petroleum naphthas via inhalation. A two-generation reproductive toxicity study of vapor recovery gasoline did not adversely affect reproductive function or offspring survival and development. Exposure to toluene during pregnancy has demonstrated limited evidence of developmental toxicity in laboratory animals. Decreased fetal body weight and increased skeletal variations in both inhalation and oral studies, but only at doses that were maternally toxic. No fetal toxicity was seen at doses that were not maternally toxic. Decreased sperm counts have been observed in male rats in the absence of a reduction in fertility. Toluene has been reported to cause mental or growth retardation in the children of solvent abusers who directly inhale toluene during pregnancy. Specific Target Organ Toxicity (Single Exposure): Epidemiology studies suggest that chronic occupational overexposure to toluene may damage color vision. Subchronic and chronic inhalation studies with toluene produced kidney and liver damage, hearing loss and central nervous system (brain) damage in laboratory animals. Intentional misuse by deliberate inhalation of high concentrations of toluene has been shown to cause liver, kidney, and central nervous system damage, including hearing loss and visual disturbances. Specific Target Organ Toxicity (Repeated Exposure): Aspiration Hazard: Symptoms/Injuries After Inhalation: Symptoms/Injuries After Skin Contact: Symptoms/Injuries After Eye Contact: Symptoms/Injuries After Ingestion: Chronic Symptoms: SECTION 12: ECOLOGICAL INFORMATION 12.1. Toxicity Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment. 12.2. Persistence and Degradability Heptane is expected to biodegrade in soil based on 100% degradation after 4 and 25 days in screening tests using gasoline contaminated soil and activated sewage sludge, respectively. Based on 100% degradation within 25 days during aerobic biodegradation screening tests, heptane is expected to biodegrade in natural water. Not expected to persist in the environment if spilled or released. 12.3. Bioaccumulative Potential An estimated BCF of 2,000 suggests the potential for bioconcentration in aquatic organisms is very high. 12.4. Mobility in Soil If released to soil, heptane is expected to have no mobility based upon an estimated Koc of 8,200. If released into water, heptane is expected to adsorb to suspended solids and sediment. Expected to have low mobility in soil and sediments with adsorption being the predominant physical process. 12.5. Other Adverse Effects SECTION 13: DISPOSAL CONSIDERATIONS 13.1. Waste treatment methods Waste Disposal Recommendations: Dispose of spilled material in accordance with state and local regulations for waste that is nonhazardous by Federal definition. Additional Information: Do not puncture or burn containers. Give empty, leaking, or full containers to disposal service equipped to handle and dispose of aerosol (pressurized) containers. SECTION 14: TRANSPORT INFORMATION 14.1 In Accordance with DOT Proper Shipping Name | Hazard Class | |<PICTOGRAM PHRASE> Identification Number| | Label Codes | | ERG Number | 14.2 In Accordance with IMDG Proper Shipping Name | Hazard Class | Identification Number| Label Codes | |<PICTOGRAM PHRASE> ntification Of The | | Substance/m | | EmS-No. (Fire) | | EmS-No. (Spillage) | | 14.3 In Accordance with IATA Proper Shipping Name |Aerosols (limited quantity) Identification Number|UN1950 |<PICTOGRAM PHRASE> Hazard Class |2.1 | Label Codes | | ntification Of The | | Substance/m | | ERG Code (IATA) |126 SECTION 15: REGULATORY INFORMATION 15.1 US Federal Regulations <COMPONENT> Section 313: This product contains: Toluene 1-4% SARA Section 311/312 Hazard Classes |Immediate ( x ) Delayed ( ) Fire ( x ) |Reactive ( ) Sudden Release of Pressure ( x ) Toxic Substances Control Act (TSCA) |All the chemicals used in this product are |TSCA listed. 15.2 US State Regulations <COMPONENT> California Prop 65: WARNING! This product contains a chemical known in the State of California to cause cancer. BENZENE WARNING! This product contains a chemical known in the State of California to cause birth defects or other reproductive harm. BENZENE TOLUENE SECTION 16: OTHER INFORMATION, INCLUDING DATE OF PREPARATION OR LAST REVISION Revision date |January 5, 2015 Other |This document has been prepared in accordance with the SDS Information |requirements of the OSHA Hazard Communication Standard 29 CFR |1910.1200. GHS Full Text Phrases: ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | ----| | -- | | Grainger disclaimer.
The information contained in this SDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this 'SDS' shall be created or inferred by any statement in this 'SDS'. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this 'SDS'. The user is responsible for full compliance.