MSDS 85048

                            MATERIAL SAFETY DATA SHEET


                 SECTION 1 --  PRODUCT AND COMPANY IDENTIFICATION

 
HMIS CODES
Health      2
Flammability   4
Reactivity   0
 
PRODUCT NAME
   85048 CARGO BLUE

MANUFACTURER'S NAME             EMERGENCY TELEPHONE NO.   
   IMPERIAL SUPPLIES LLC         800-255-3924  CHEM-TEL
   789 Packer Drive
   Green Bay, WI. 54304

DATE OF PREPARATION              INFORMATION TELEPHONE NO.
   27-SEP-04                       800-558-2808
 

               SECTION 2 --  COMPOSITION/INFORMATION ON INGREDIENTS


% by WT   CAS No.       INGREDIENT   UNITS                          VAPOR PRESSURE
--------------------------------------------------------------------------------
14        74-98-6       Propane      
                                     ACGIH TLV   2500    ppm            760 mm
                                     OSHA  PEL   1000   ppm
13        106-97-8     Butane
                                     ACGIH TLV   800   ppm              760 mm
                                     OSHA  PEL   800   ppm
22        108-88-3     Toluene
                                     ACGIH TLV   50   ppm   (Skin)     22 mm
                                     OSHA  PEL   100   ppm   (Skin)
                                     OSHA  PEL   150   ppm   (Skin) STEL
34        67-64-1       Acetone
                                     ACGIH TLV   500   ppm              180 mm
                                     ACGIH TLV   750   pmm   STEL
                                     OSHA  PEL  1000   ppm
3          763-69-9     Ethyl   3-Ethoxypropionate
                                     ACGIH TLV Not Available        1.11 mm
                                     OSHA  PEL Not Available   
2          13463-67-7   Titanium Dioxide
                                     ACGIH TLV   10 mg/m3 as Dust
                                     OSHA  PEL   10 mg/m3 Total Dust
                                     OSHA  PEL   5 mg/m3 Respirable Fraction
 

                        SECTION 3 - HAZARDS IDENTIFICATION

 
ROUTES OF EXPOSURE

INHALATION of vapor or spray mist.

EYE or SKIN contact with the product, vapor or spray mist. 

EFFECTS OF OVEREXPOSURE

EYES:  Irritation.

SKIN:  Prolonged or repeated exposure may cause irritation.

INHALATION: Irritation of the upper respiratory system. 
May cause nervous system depression. Extreme overexposure may result in 
unconsciousness and possibly death. 

SIGNS AND SYMPTOMS OF OVEREXPOSURE
Headache, dizziness, nausea, and loss of coordination are indications of 
excessive exposure to vapors or spray mists. 
Redness and itching or burning sensation may indicate eye or excessive skin 
exposure. 

MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE
None generally recognized. 

CANCER INFORMATION
For complete discussion of toxicology data refer to Section 11. 
 

                          SECTION 4 - FIRST AID MEASURES

 
EYES: Flush eyes with large amounts of water for 15 minutes. Get medical 
attention.

SKIN: Wash affected area thoroughly with soap and water. 
   Remove contaminated clothing and launder before re-use. 

INHALATION: If affected, remove from exposure. Restore breathing. 
   Keep warm and quiet. 

INGESTION: Do not induce vomiting. Get medical attention immediately. 
 

                       SECTION 5 --  FIRE FIGHTING MEASURES

 
FLASH POINT         LEL      UEL
Propellant < 0 F         1.0      12.8

EXTINGUISHING MEDIA
Carbon Dioxide, Dry Chemical, Foam   

UNUSUAL FIRE AND EXPLOSION HAZARDS
Containers may explode when exposed to extreme heat. 
Application to hot surfaces requires special precautions. 
During emergency conditions overexposure to decomposition products may cause a 
health hazard. Symptoms may not be immediately apparent. Obtain medical 
attention. 

SPECIAL FIRE FIGHTING PROCEDURES
Full protective equipment including self-contained breathing apparatus should be 
used. 
Water spray may be ineffective. If water is used, fog nozzles are preferable. 
Water may be used to cool closed containers to prevent pressure build-up and 
possible autoignition or explosion when exposed to extreme heat. 
 

                    SECTION 6 --  ACCIDENTAL RELEASE MEASURES

 
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Remove all sources of ignition. Ventilate the area. Remove with inert absorbent. 
 

                         SECTION 7 - HANDLING AND STORAGE

 
STORAGE CATEGORY
Not Available.
 
PRECAUTIONS OT BE TAKEN IN HANDLING AND STORAGE
Keep away from heat, sparks, and open flame. Vapors will accumulate readily and 
may ignite explosively. 
During use and until all vapors are gone: Keep area ventilated - Do not smoke - 
Extinguish all flames, pilot lights, and heaters - Turn off stoves, electric 
tools and appliances, and any other sources of ignition.
Consult NFPA code. Use approved bonding and Grounding procedures.  
Contents under pressure. Do not puncture, incinerate, or expose to  temperature 
above 120F. Heat from sunlight, radiators, stoves, hot water, and other heat 
sources could cause container to burst. Do not take internally. Keep out of the 
reach of children.
 

               SECTION 8 --  EXPOSURE CONTROLS/PERSONAL PROTECTION

 
PRECAUTIONS TO BE TAKEN IN USE
Use only with adequate ventilation.
Avoid contact with skin and eyes. Avoid breathing vapor and spray mist. Wash 
hands after using.
This coating may contain materials classified as nuisance particulates (listed 
"as Dust" in Section 2) which may be present at hazardous levels only during 
sanding or abrading of the dried film. If no specific dusts are listed in 
Section 2, the applicable limits for nuisance dusts are ACGIH TLV 10 mg/m3 
(total dust), 3 mg/m3 (respirable fraction), OSHA PEL 15 mg/m3 (total dust), 5 
mg/m3 (respirable fraction).

VENTILATION
Local exhaust preferable. General exhaust acceptable if the exposure to  
materials in Section 2 is maintained below applicable exposure limits. 
Refer to OSHA Standards 1910.94, 1910.107, 1910.108.

RESPIRATORY PROTECTION
If personal exposure cannot be controlled below applicable limits by 
ventilation, wear a properly fitted organic vapor/particulate respirator 
approved by NIOSH/MSHA for protection against material in Section 2.
When sanding or abrading the dried film, wear a dust/mist respirator approved by 
NIOSH/MSHA for dust which may be generated from this product, underlying paint, 
or the abrasive. 

PROTECTIVE GLOVES
None required for normal application of aerosol products where minimal skin 
contact is expected. For long or repeated contact, wear chemical resistant 
gloves. 

EYE PROTECTION
Wear safety spectacles with unperforated sideshields. 

OTHER PRECAUTIONS.
Intentional misuse by deliberately concentrating and inhaling the contents can 
be harmful or fatal. 
 

                  SECTION 9 --  PHYSICAL AND CHEMICAL PROPERTIES

 
PRODUCT WEIGHT         6.24 lb/gal   747 g/l
SPECIFIC GRAVITY      0.75
BOILING POINT         <0 - 342 F   <-18 - 172 C
MELTING POINT         Not Available
VOLATILE VOLUME      91 %
EVAPORATION RATE      Faster than ether
VAPOR DENSITY         Heavier than air
SOLUBILITY IN WATER      N.A.
pH                7.0
VOLATILE ORGANIC COMPOUNDS (VOC Theoretical )
Volatile Weight 52.27 %     Less Water and Federally Exempt Solvents.
 

                     SECTION 10 --  STABILITY AND REACTIVITY

 
STABILITY - Stable

CONDITIONS TO AVOID
None known.

INCOMPATIBILITY 
None known. 

HAZARDOUS DECOMPOSITION PRODUCTS
By fire: Carbon Dioxide, Carbon Monoxide

HAZARDOUS POLYMERIZATION
Will not occur
 

                     SECTION 11 --  TOXICOLOGICAL INFORMATION

 
CHRONIC HEALTH HAZARDS
No ingredient in this product is an IARC, NTP, or OSHA listed carcinogen. 
Prolonged overexposure to solvent ingredients in Section 2 may cause adverse
effects to the liver, urinary, cardiovascular and reproductive systems.
Rats exposed to titanium dioxide dust at 250 mg./m3 developed lung cancer, 
however, such exposure levels are not attainable in the workplace.
Reports have associated repeated and prolonged overexposure to solvents with 
permanent brain and nervous system damage. 

TOXICOLOGY DATA

CAS No.      Ingredient Name
--------------------------------------------------------------------------------
74-98-6     Propane   
               LC50   RAT   4HR   Not Available
               LD50   RAT      Not Available
106-97-8    Butane
               LC50   RAT   4HR   Not Available
               LD50   RAT      Not Available
108-88-3    Toluene
               LC50   RAT   4HR   4000   ppm
               LD50   RAT      5000   mg/kg
67-64-1     Acetone
               LC50   RAT   4HR   Not Available
               LD50   RAT      5800      mg/kg
763-69-9    Ethyl 3-Ethoxypropionate
               LC50   RAT   4HR   Not Available
               LD50   RAT      5000   mg/kg
13463-67-7   Titanium Dioxide
                   LC50   RAT   4HR   Not Available
                   LD50   RAT      Not Available
 

                      SECTION 12 --  ECOLOGICAL INFORMATION

 
ECOTOXICOLOGICAL INFORMATION
No data available. 
 

                       SECTION 13 - DISPOSAL CONSIDERATIONS

 
WASTE DISPOSAL METHOD
Waste from this product may be hazardous as defined under the Resource 
Conservation and Recovery Act (RCRA) 40 CFR 261.
Waste must be tested for ignitability to determine the applicable EPA hazardous 
waste numbers.  Do not incinerate. Depressurize container. Dispose of in 
accordance with Federal, State/Provincial, and Local regulations regarding 
pollution. 
 

                        SECTION 14 - TRANSPORT INFORMATION

 
No data available. 
 

                       SECTION 15 - REGULATORY INFORMATION

 
SARA 313 (40 CFR 372.65C) SUPPLIER NOTIFICATION
 
CAS NO.      CHEMICAL/COMPOUND      % by WT   % Element
108-88-3   Toluene                   22
 
CALIFORNIA PROPOSITION 65
WARNING:  This product contains chemicals known to the State of California to 
cause cancer and birth defects or other reproductive harm. 
 
TSCA CERTIFICATION
All chemicals in this product are listed, or are exempt from listing, on the 
TSCA Inventory.
 

                         SECTION 16 --  OTHER INFORMATION

 
This product has been classified in accordance with the hazard criteria of the 
Canadian Controlled Products Regulations (CPR) and the MSDS contains all of the 
information required by the CPR.
 
The above information pertains to this product as currently formulated, and is 
based on the information available at this time. Addition of reducers or other 
additives to this product may substantially alter the composition and hazards of 
the product. Since conditions of use are outside our control, we make no 
warranties, express or implied, and assume no liability in connection with any 
use of this information

The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance.

© 2008 Imperial Supplies LLC Questions or comments? Contact us.