MSDS Sheet 82104

• All Products
• Fasteners
   » Grade 8
   » Grade 5
   » Threaded Fasteners
• Hardware
• Rivet & Rivet Guns
• Vehicle Lighting
• Electrical Products
• Tubing & Tube Fittings
• Air Brake Products
• Hose & Hose Ends
• Cutting Tools
• Abrasives
• Safety Products &
  Welding Supplies
• Chemicals & Paint
   » MSDS Information
   » CA/OTC Information
• Shop Supplies
• Vehicle Parts &
  Accessories
• Assortments &
  Steel Equipment
   » Assortment Listing

• Online Catalog Index
• Discontinued &
Overstock Specials

Printer-Friendly View

MATERIAL SAFETY DATA SHEET PART NO: 82104 82110 PRODUCT NAME: ENERGIZED ROSIN CORE SOLDER 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Manufacturer's Name: COOKSON ELECTRONICS ASSEMBLY MATERIALS GROUP Address: 4100 6th Avenue Altoona, PA 16602 Transport Emergency #: CHEMTREC: 1-800-424-9300 Business Phone: 1-814-946-1611 2. INGREDIENT AND EXPOSURE LIMIT INFORMATION Chemical Name CAS # % W/W OSHA PEL - TWA -------------------------------------------------------------------------------- Lead 7439-92-1 20-80 % 0.05 mg/m3 Tin 7440-31-5 20-80 % 2.0 mg/m3 WW gum Rosin * 8050-09-7 1-4 ** Propylene Glycol Ether 1589-47-5 1-4 100 PPM Tetrahydrofurfuryl Alcohol 97-99-4 1-4 2 PPM Resin H * 65997-06-0 1-4 ** Product contains one or more of these metallic elements in varying. Percentages. See product label for exact composition. *Sensitizer reduce exposure to as low as possible. 3. HAZARDS IDENTIFICATION Emergency overview: Moderate eye irritant. Will not burn, toxic by inhalation. Gastrointestinal tract irritant. Respiratory tract irritant. Causes skin irritation. HMIS RATING SYSTEM: Health: 3 Flammability: 0 Reactivity: 0 Protection: B NFPA Rating System: Health: 3 Flammability: 0 Reactivity: 0 Routes of Entry: Inhalation: Ingestion: Skin Contact: Eye Contact: Absorption: Target Organs: Blood: Digestive Tract: Kidneys: Respiratory System: Nervous System: Eyes: Skin: Medical Conditions Aggravated: Digestive Tract Disease: Kidney Disease Immediate (Acute) Symptoms over-exposure by route of exposure: Inhalation; Can cause moderate respiratory irritation, Dizziness, weakness, Fatigue, nausea and headache. Eyes: Can cause moderate irritation, tearing and reddening, but not likely to permanently injure eye tissue. Skin Contact: Can cause slight irritation. Ingestion: Irritating to mouth, throat, and stomach, can cause abdominal discomfort, nausea, vomiting and diarrhea. Long term (Chronic) Health effects: Carcinogenicity: IARC classifies lead and some lead compound as 2B Carcinogens to humans. AGCIH lists lead as a "A3" (animal carcinogen with unknown relevance to humans). See Section 11 of the MSDS for additional information. Reproduction: See Section 11 of this MSDS. Mutacenicity: See Section 11 of this MSDS. 4. FIRST AID MEASURES Skin Exposure: Wash with soap and water. Remove contaminated clothing and launder. Get medical attention if irritation develops or persists. Eye Exposure: Flush eyes with plenty of water for at least 20 minutes. Retracting eyelids often. Tilt the head to prevent chemical from transferring to the uncontaminated eye. Get immediate medical attention. Inhalation: Remove to fresh air. If breathing is difficult, have a trained individual administer oxygen. If not breathing, give artificial respiration and have a trained individual administer oxygen. Get medical attention immediately. Ingestion: Seek medical attention immediately. Notes to Doctor; No additional first aid information available. 5. FIRE FIGHTING MEASURES Flammability Summary: Not Combustible Flash Point: N/A Autoignition Temperature: N/E Explosive Limits % in Air: N/E Fire Fighting Methods: Will not burn, no special instructions available. Use methods appropriate for surrounding materials. Hazardous Combustion Products; Metal Fumes: Toxic Fumes 6. ACCIDENTAL RELEASE MEASURES Precautions and Equipment: Exposure to the spilled material may be irritating or harmful. Follow personal protective equipment recommendations found in section VIII of this MSDS. Methods for Clean-up: Wear complete and proper personal protective equipment Following the recommendation of section VIII gather and Store in a sealed container pending a waste disposal evaluation. Do not use broom or air cleaning etc. 7. HANDLING AND STORAGE Handling Measures: Harmful or irritating material. Avoid contacting and avoid breathing the material. Use only in a well ventilated area. As with all chemicals, good industrial hygiene practices should be followed when handling this material. Avoid breathing dusts or fumes, use only in a well ventilated area. Wash thoroughly after handling: Wash hands before eating: Do not get in eyes, or on skin and clothing: Minimize dust generation and accumulation: Remove contaminated clothing and wash before reuse. Storage Measures; Store in a tightly closed container: Keep away from food and drinking water. Store in a cool dry place: Keep away from heat, sparks, and flame. 8. EXPOSURE CONTROLS AND PERSONAL PROTECTION Engineering Measures: Use local exhaust ventilation or other engineering controls to minimize exposures and maintain operator comfort. Engineering controls must be designed to meet the OSHA Chemical specific standard in 29 CFR 1910. Ventilation is required to maintain operator exposure below published exposure limits. Use process enclosures, local exhaust ventilation, or there engineering controls to control airborne levels below recommended exposure limits. Respiratory Protection: Respiratory protection may be required to avoid overexposure when handling this product. General or local exhaust ventilation is the preferred means of protection. Use a respirator if general room ventilation is not available or sufficient to eliminate symptoms. Follow a respiratory protection program that meets 29 CFR 1910.134 and ANSI Z88.2 requirements whenever work place conditions warrant the use of a respirator. Wear a NIOSH approved respirator if any exposure is possible. Eye Protection; Wear chemically resistant safety glasses with side shields when handling this product. Do not wear contact lenes. Wear goggles and a face shield. Skin Protection: Wear protective gloves. Inspect gloves for chemical break- through and replace at regular intervals. Clean protective equipment regularly. Wash hands and other exposed areas with mild soap and water before eating, drinking, and when leaving work. Where contact is likely, wear chemical resistant gloves, a chemical suit, rubber boots, and chemical safety goggles plus a face shield. CONTROL PARAMETERS: -----------ACGIH EXPOSURE LIMITS---------- Chemical Name TLV-TWA STEL CEILING Lead 0.05 mg/m3 TWA Tin 2 mg/m3 TWA WW Gum Rosin SENSITIZER REDUCE EXPOSURE AS LOW AS POSSIBLE Rosin SH SENSITIZER REDUCE EXPOSURE AS LOW AS POSSIBLE 9. PHYSICAL AND CHEMICAL PROPERTIES Color; Grey Odor: None pH: N/A Solubility in Water: NEGLIGIBLE: 0-1 % Other Physical And Chemical Properties Depend on Alloy Composition. 10. STABILITY AND REACTIVITY Decomposition Products: Metal Fumes: Toxic Fumes. Incompatible Materials: Peroxides: Metals: Strong Acids: Strong Oxidizing Agents: Strong Reducing Agents: Acids: Chlorine: Moisture: Strong Alkalies Conditions to Avoid: None Known Contamination: Contact With Air. Contact with Water 11. TOXICOLOGICAL INFORMATION Inhalation And Ingestion; Ingestion of dust or fume Must be Avoided. Lead: Lead is toxic and cumulative, affecting the kidneys and nervous system. Symptoms include anemia, insomnia, weakness, irritability, constipation and stomach pains. Consult OSHA lead Standard 1910.1025. Tin: Dust or fume may cause irritation of the skin and mucous membranes and May result in benign pneumoconiosis (stannosis) 12. ECOLOGICAL INFORMATION Overview; Ecological Hazard. In high concentrations, this product may be dangerous to plants and/or wildlife. 13. DISPOSAL CONSIDERATIONS Waste Description: Return to supplier to be recycled for metal unit value. Spent or discarded material is probably a hazardous waste. Disposal Method: Dispose of in accordance with Federal, State, Local or Provincial Laws and regulations. 14. TRANSPORT INFORMATION Shipping Basic Description: DOT & IATA: Not restricted unless in fine particle size less than 0.004 inches in diameter. Depends on Alloy. Consult label or manufacturer for additional information. 15. REGULATORY INFORMATION TSCA STATUS: All components of this product are listed on the TSCA Inventory of existing chemical substances. Regulated Chemicals: Chemical Name Regulation -------------------------------------------------------------------------------- Lead 7439-92-1 SARA 313 Lead 7439-92-1 CA PROP 65 16. OTHER INFORMATION The information contained herein is based on data considered accurate. However, no warranty is expressed of implied regarding the accuracy of these data or the results to be obtained from the use thereof. Additionally, Alpha Metals, Inc. assumes no responsibility for injury to the vendee or third persons proximately caused by the material even if reasonable safety procedures are followed. Furthermore, vendee assumes the risk in his use of the material.