|
|
Printer Friendly View
72578: Heat Shrink 18 Ga X 6 Red [10]
72579: Heat Shrink 14 Ga X 6 Blue [10]
72580: Heat Shrink 10 Ga X 6 Yellow [10]
MSDS Last updated: 03/02/2006
3M General Offices 3M Center
St. Paul, MN. 55144-1000
1-800-364-3577 or (651) 737-6501 (24 hours)
HST200
MATERIAL SAFETY DATA SHEET
3M
Copyright, 2001, Minnesota Mining and Manufacturing Company. All rights
reserved. Copying and/or downloading of this information for the purpose of
properly utilizing 3M products is allowed provided that;
(1) the information is copied in full with no changes unless prior agreement
is
obtained from 3M, and
(2) neither the copy nor the original is resold or otherwise distributed with
the intention of earning a profit thereon.
DIVISION; ELECTRICAL PRODUCTS DIVISION
TRADE NAME;
EPS SERIES HEAT SHRINK TUBING - RED, BLACK, CLEAR, GRAY
ISSUED; MARCH 12, 2001
SUPERSEDES; FEBRUARY 2, 2001
DOCUMENT; 06-3105-1
1. INGREDIENT C.A.S. NO. PERCENT
--------------------------------------------------------------------------------
Adhesive Lined Polyolefin Tubing -
Flame Retardant Unknown 100
Ethylene-Ethyl Acrylate Polymer 9010-86-0 50 - 60
Decabromodiphenyl Ether 1163-19-5 15 - 25
Antimony Trioxide 1309-64-4 1 - 10
Zinc Oxide 1314-13-2 1 - 10
Magnesium Oxide 1309-48-4 1 - 10
Polyethylene 9002-88-4 1 - 10
Trimethylolpropane
Trimethacrylate 3290-92-4 1 - 10
Carbon Black 1333-86-4 0.5 - 3
Tetrakis{Methylene(3,5-Di-Tert-
Butyl-4-Hydroxyhydrocinnamate)}
Methane 6683-19-8 0.1 - 3
Bis (3,5-Di-Tert-Butyl-4-
Hydroxyhydrocinnamoyl)Hydrazine 32687-78-8 0.1 - 3
Hindered Phenolic Anitoxidant Unknown 0.1 - 2
Thiodiethylene Bis(3,5-Di-Tert-
Butyl-4-Hydroxythydrocinnamate) 41484-35-9 0.1 - 3
Dilauryl 3,3'-Thiodipropionate 123-28-4 0.1 - 3
Stearic Acid 57-11-4 0.1 - 2
Nonabromodiphenyl Oxide 63936-56-1 0.1 - 0.7
NOTE: The components of this product are in compliance with the chemical
notification requirements of TSCA.
See Section 4 for Hazardous Decomposition Products. Hazardous components
are encased in polymeric matrix throughout normal application
temperatures and therefore present minimal potential for exposure.
THIS PRODUCT CONTAINS THE FOLLOWING TOXIC CHEMICAL OR
CHEMICALS SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313
OF TITLE III OF THE EMERGENCY PLANNING AND COMMUNITY RIGHT-TO-
KNOW ACT OF 1986 AND 40 CFR PART 372;
DECABROMODIPHENYL ETHER
THIS PRODUCT CONTAINS THE FOLLOWING TOXIC CHEMICAL OR
CHEMICALS SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313
OF TITLE III OF THE EMERGENCY PLANNING AND COMMUNITY RIGHT-TO-
KNOW ACT OF 1986 AND 40 CFR PART 372;
ANTIMONY TRIOXIDE
ZINC OXIDE
2. PHYSICAL DATA
--------------------------------------------------------------------------------
BOILING POINT; N/A
VAPOR PRESSURE; N/A
VAPOR DENSITY; N/A
EVAPORATION RATE; N/A
SOLUBILITY IN WATER; N/A
SP. GRAVITY; 1.25-1.30 water = 1
PERCENT VOLATILE: N/A
pH; N/A
VISCOSITY; N/A
MELTING POINT; N/D
APPEARANCE AND ODOR; Various colors and sizes, odorless
3. FIRE AND EXPLOSION HAZARD DATA
--------------------------------------------------------------------------------
FLASH POINT; N/A
FLAMMABLE LIMITS - LEL; N/A
FLAMMABLE LIMITS - UEL; N/A
AUTOIGNITION TEMPERATURE; N/D
EXTINGUISHING MEDIA;
Carbon dioxide, Dry chemical, Foam
SPECIAL FIRE FIGHTING PROCEDURES;
Wear full protective clothing, including helmet, self-contained, positive
pressure or pressure demand breathing apparatus, bunker coat and pants, bands
around arms, waist and legs, face mask, and protective covering for exposed
areas of the head.
UNUSUAL FIRE AND EXPLOSION HAZARDS;
None known.
NFPA HAZARD CODES; HEALTH; 1 FIRE; 1 REACTIVITY; 0
UNUSUAL REACTION HAZARD; none
OSHA FIRE HAZARD CLASS; Not applicable
4. REACTIVITY DATA
--------------------------------------------------------------------------------
STABILITY; Stable
INCOMPATIBILITY - MATERIALS TO AVOID;
None known.
HAZARDOUS POLYMERIZATION; Will not occur
HAZARDOUS DECOMPOSITION PRODUCTS;
Under recommended usage conditions, hazardous decomposition products are not
Expected. Hazardous decomposition products anticipated as a result of oxidation
(excluding burning), heating, or reaction with another material may include;
Carbon Monoxide and Carbon Dioxide, Aldehydes, Hydrogen Bromide, Oxides
Of Zinc, Oxides of Antimony, Acetic Acid, Toxic Vapors, Gases or Particulates,
Irritant vapors or gases. Initial decomposition begins at 180 C, and above 240 C
Significant decomposition occurs with the formation of decomposition products
Listed above.
Heating product beyond temperature recommended by instruction sheet may cause
Release of the following compounds; Benzene, Toluene, Formaldehyde,
Acetaldehyde, Acetic Acid, vinyl Acetate, and Hydrogen Bromide.
5. ENVIRONMENTAL INFORMATION
--------------------------------------------------------------------------------
SPILL RESPONSE;
Not applicable.
RECOMMENDED DISPOSAL;
Dispose of waste product in a sanitary landfill.
ENVIRONMENTAL DATA;
No data available.
REGULATORY INFORMATION
Volatile Organic Compounds; N/A
VOC less H20 & Exempt Solvents; N/A
Since regulations vary, consult applicable regulations or authorities before
disposal.
EPCRA HAZARD CLASS;
FIRE HAZARD; No PRESSURE; No REACTIVITY; No ACUTE; No
CHRONIC; No
6. SUGGESTED FIRST AID
--------------------------------------------------------------------------------
EYE CONTACT;
Immediately flush eyes with large amounts of water. Get immediate medical
attention.
SKIN CONTACT;
If skin contact with hot material occurs; DO NOT ATTEMPT TO REMOVE MOLTEN
MATERIAL. Immediately flush affected area with plenty of cold water and cover
with a clean dressing. Have burn treated by a physician.
INHALATION; If signs/symptoms occur, remove person to fresh air. If
signs/symptoms continue, call a physician.
IF SWALLOWED;
Drink two glasses of water. Call a physician.
7. PRECAUTIONARY INFORMATION
--------------------------------------------------------------------------------
EYE PROTECTION;
AVOID EYE CONTACT WITH VAPORS OR SMOKE RESULTING FROM OVERHEATING OR WHEN USED
IN CONFINED AREAS.
SKIN PROTECTION;
Avoid skin contact with hot material. Wear appropriate gloves, such as Nomex,
when handling this material to prevent thermal burns.
VENTILATION PROTECTION;
Local exhaust is required for operations using large amounts of material.
Conduct air monitoring to determine adequacy of ventilation. Use in a
well-ventilated area. Provide sufficient ventilation to maintain emissions below
recommended exposure limits.
If exhaust ventilation is not adequate, use appropriate respiratory protection.
WHEN USING THIS PRODUCT IN A CONFINED SPACE OR WHERE VENTILATION MAY BE
INADEQUATE THEN RESPIRATORY PROTECTION MAY BE WORN. INADEQUATE VENTILATION OR
CONFINED SPACES WOULD CAUSE VAPORS FROM HEATING OF THIS PRODUCT TO BE PRESENT IN
THE USER'S BREATHING ZONE ANY MAY CAUSE RESPIRATORY IRRITATION. EXCESSIVE
HEATING OF THIS PRODUCT BEYOND THE RECOMMENDED APPLICATION TEMPERATURE OF 250
DEGREES FAHRENHEIT IS NOT RECOMMENDED AND MAY RESULT IN THERMAL DEGRADATION AND
DECOMPOSITION PRODUCTS WHICH MAY RESULT IN ADVERSE HEALTH EFFECTS.
RESPIRATORY PROTECTION;
Avoid breathing of fumes. Select one of the following NIOSH approved respirators
based on airborne concentration of contaminants and in accordance with OSHA
regulations;
Half-mask organic vapor respirator with dust/mist prefilter.
PREVENTION OF ACCIDENTAL INGESTION;
Wash hands after handling and before eating.
RECOMMENDED STORAGE;
Store at room temperature. Keep out of the reach of children.
FIRE AND EXPLOSION AVOIDANCE;
Not applicable.
OTHER PRECAUTIONARY INFORMATION;
HMIS HAZARD RATINGS; HEALTH; 1 FLAMMABILITY; 1 REACTIVITY; 0
PERSONAL PROTECTION; A
EXPOSURE LIMITS
INGREDIENTS VALUE UNIT TYPE AUTH SKIN*
Adhesive Lined Polyolefin Tubing -
Flame Retardant NONE NONE NONE NONE
Ethylene-Ethyl Acrylate Polymer NONE NONE NONE NONE
Decabromodiphenyl Ether 5 mg/m3 TWA CMRG
Decabromodiphenyl Ether 5 mg/m3 TWA AIHA
Antimony Trioxide 0.5 mg/m3 TWA ACGIH
As Sb
Zinc Oxide 10 mg/m3 TWA ACGIH
AS DUST
Zinc Oxide 10 mg/m3 TWA OSHAV
AS DUST
OSHA VACATED PEL
Zinc Oxide 5 mg/m3 TWA ACGIH
As fume
Zinc Oxide 10 mg/m3 STEL ACGIH
As fume
Zinc Oxide 5 mg/m3 TWA OSHA
As fume
Zinc Oxide 10 mg/m3 STEL OSHAV
As fume
OSHA VACATED PEL
Zinc Oxide 15 mg/m3 TWA OSHA
AS TOTAL DUST
Zinc Oxide 5 mg/m3 TWA OSHA
RESPIRABLE
Magnesium Oxide 10 mg/m3 TWA ACGIH
As fume
Magnesium Oxide 15 mg/m3 TWA OSHA
AS TOTAL DUST
Polyethylene NONE NONE NONE NONE
Trimethylolpropane Trimethacrylate 25 ppm TWA CMRG
TrimethylolpropANE Trimethacrylate 1 mg/m3 TWA AIHA
Carbon Black 3.5 mg/m3 TWA ACGIH
Carbon Black 3.5 mg/m3 TWA OSHA
Carbon Black 0.5 mg/m3 TWA CMRG
Tetrakis{Methylene(3,5-Di-Tert-
Butyl-4-Hydroxyhydrocinnamate)}
Methane NONE NONE NONE NONE
Bis(3,5-Di-Tert-Butyl-4-
Hydroxyhydrocinnamoyl)hydrazine NONE NONE NONE NONE
Hindered Phenolic Anitoxidant NONE NONE NONE NONE
Thiodiethylene Bis(3,5-Di-Tert-
Butyl-4-Hydroxythydrocinnamate) NONE NONE NONE NONE
Dilauryl 3,5'-Thiodipropionate NONE NONE NONE NONE
Stearic Acid 10 mg/m3 TWA ACGIH
AS TOTAL DUST
Nonabromodiphenyl Oxide NONE NONE NONE NONE
*SKIN NOTATION; Listed substances indicated with "Y" under SKIN refer to the
potential contribution to the overall exposure by the coetaneous route including
mucous
Membrane and eye, either by airborne or, more particularly, by direct contact
with the substance. Vehicles can alter skin absorption.
SOURCE OF EXPOSURE LIMIT DATA;
-ACGIH; American Conference of Governmental Industrial Hygienists.
-AIHA: American Industrial Hygiene Assoc. Workplace Environmental Exposure Level
Guideline
-OSHA; Occupational Safety and Health Administration
-OSHAV: Occupational Safety and Health Administration Vacated PEL.
Vacated Permissible Exposure Limits (PEL) are enforced as the OSHA PEL in some
states. Check with your local regulatory authority.
-CMRG: Chemical Manufacture Recommended Guidelines.
-NONE; None Established.
8. HEALTH HAZARD DATA
--------------------------------------------------------------------------------
EYE CONTACT;
Vapors from heated material may cause eye irritation.
SKIN CONTACT;
Skin Burns (thermal, from contact with hot material): signs/symptoms can include
burning pain, red and swollen skin, and blisters.
INHALATION;
Vapors of heated material may cause respiratory system irritation.
RESPIRATORY IRRITATION WOULD NOT BE EXPECTED IN APPLICATIONS WHERE ADEQUATE
VENTILATION AND PROPER APPLICATION (AT DESIGNATED TEMPERATURES) IS UTILIZED.
EXCESSIVE HEATING AND INADEQUATE VENTILATION MAY RESULT IN EXPOSURE TO THERMAL
DEGRADATION AND DECOMPOSITION PRODUCTS AS INDICATED IN SECTION 4 OF THIS MSDS
UNDER 'REACTIVITY DATA-HAZARDOUS DECOMPOSITION PRODUCTS".
IF SWALLOWED;
Ingestion is not a likely route of exposure to this product.
SECTION CHANGE DATES
PRECAUT. INFO. SECTION CHANGED SINCE FEBRUARY 2, 2001 ISSUE
Abbreviations; N/D - Not Determined N/A - Not Applicable CA - Approximately
The information in this Material Safety Data Sheet (MSDS) is believed to be
correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE.
User is responsible for determining whether the 3M product is fit for a
particular purpose and suitable for user's method of use or application. Given
the variety of factors that can affect the use and application of a 3M product,
some of which are uniquely within the user's knowledge and control, it is
essential that the user evaluate the 3M product to determine whether it is fit
for a particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to
the remote possibility that electronic transfer may have resulted in errors,
omissions or alterations in this information, 3M makes no representations as to
its completeness or accuracy., In addition, information obtained from a database
may not be as current as the information in the MSDS available directly from 3M.
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance.
For more product information by email, click here
Imperial Supplies LLC does not provide services and products outside the United States
|
