MSDS 71721

                          MATERIAL SAFETY DATA SHEET

PART NO: 71721-71726
         71728-71740-1
PRODUCT NAME: THERMOFIT HEAT-SHRINKABLE POLYMERIC PRODUCTS


NFPA RATING:                                HMIS RATING:
HEALTH:                                     HEALTH:
FLAMMABILITY:                               FLAMMABILITY:
REACTIVITY:                                 REACTIVITY:
SPECIAL:                                    PERSONAL PROT:

                             ******SECTION I******

MANUFACTURER'S NAME: IMPERIAL SUPPLIES LLC
MANUFACTURER'S ADDRESS: 789 PACKER DRIVE
CITY, STATE, ZIP: GREEN BAY, WI 54307
INFORMATION TELEPHONE NUMBER: 800-558-2808
EMERGENCY TELEPHONE NUMBER: 800-255-3924 (CHEM-TEL, INC.)
DATE PREPARED:

             ***SECTION II: HAZARDOUS INGREDIENTS/IDENTITY INFO***

HAZARDOUS COMPONENTS:

 INGREDIENTS           CAS#      %         OSHA PEL     ACGIH TLV
--------------------------------------------------------------------------
HEAT-SHRINKABLE POLYMERIC PRODUCTS ARE NOT HAZARDOUS DURING PROPER
INSTALLATION BUT MAY EMIT HAZARDOUS THERMAL DECOMPOSITION AND COMBUSTION
BYPRODUCTS IF OVERHEATED TO DEGRADATION. SEE "THERMAL DEGRADATION AND
COMBUSTION BYPRODUCT" SECTION OF THIS MSDS FOR MORE SPECIFIC INFORMATION. BASE
POLYMER MATERIALS INCLUDE POLYETHYLENE AND OLEFIN COPOLYMERS, FLUOROPOLYMERS,
CHLOROPOLYMERS, POLYAMIDES, POLYESTERS, AND SILICONES. HEAT-SHRINKABLE
PRODUCTS MAY BE COATED WITH OR USED IN CONJUNCTION WITH ADHESIVES/MASTICS
WHICH ARE BASED ON OLEFIN COPOLYMERS OR POLYAMIDES.


                             PRODUCT APPLICATIONS

TYPICAL USED OF HEAT-SHRINKABLE POLYMERIC PRODUCTS INCLUDE PRIMARY ELECTRICAL
INSULATION, EMI/RFI SHIELDING, CABLE JACKETING AND REPAIR, STRAIN RELIEF,
COMPONENT ENCAPSULATION, WATERPROOFING, PACKAGING, ENVIRONMENTAL/MECHANICAL
PROTECTION, AND CABLE JOINING, SPLICING, AND TERMINATION IN COMMERCIAL AND
MILITARY/AEROSPACE ELECTRONIC APPLICATIONS.



                    ***PHYSICAL/CHEMICAL CHARACTERISTICS***

VAPOR PRESSURE (MMHG) @ 20C: NOT APPLICABLE
APPEARANCE AND ODOR: PLASTIC TUBING AND MOLDED PARTS IN A VARIETY OF SHAPES,
SIZES AND COLORS. NO ODOR.


                  ***SECTION IV: FIRE AND EXPLOSION HAZARD DATA***

FLASH POINT (METHOD USED): NOT APPLICABLE
FLAMMABLE LIMITS:
LEL: N/A
UEL: N/A

EXTINGUISHING MEDIA: CARBON DIOXIDE, WATER, DRY CHEMICAL OR FOAM.

SPECIAL FIRE FIGHTING PROCEDURES: FIREFIGHTERS SHOULD WEAR SELF-CONTAINED
BREATHING APPARATUS IN ENCLOSED AREAS.

UNUSUAL FIRE AND EXPLOSION HAZARDS: TOXIC FUMES MAY EVOLVE IN A FIRE.



                       ***SECTION V: REACTIVITY DATA***

STABILITY: STABLE
CONDITIONS TO AVOID: AVOID OVERHEATING OF PRODUCT

INCOMPATIBILITY (MATERIALS TO AVOID):

HAZARDOUS DECOMPOSITION OR BY PRODUCTS:

HAZARDOUS POLYMERIZATION:
CONDITIONS TO AVOID:



                     ***SECTION VI: HEALTH HAZARD DATA***

ROUTES OF ENTRY:

HEALTH HAZARDS (ACUTE AND CHRONIC):
IN COMMON WITH MOST ORGANIC MATERIALS, DEGRADATION AND COMBUSTION BYPRODUCTS
MAY BE TOXIC AND SHOULD NOT BE INHALED. (SEE THERMAL DEGRADATION AND
COMBUSTION BYPRODUCTS SECTION FOR MORE SPECIFIC INFORMATION) OVERHEATING THE
PRODUCT TO CHARRING OR BURNING WILL PRODUCE FUMES THAT MAY CAUSE EYE, SKIN,
NOSE AND THROAT IRRITATION.

TOXICOLOGICAL INFORMATION/EXPOSURE LIMITS: NONE ESTABLISHED FOR POLYMER
MIXTURES.

SUSPECTED CANCER AGENT:  NO INGREDIENT OF THESE PRODUCTS THAT IS PRESENT AT
CONCENTRATIONS EQUAL TO OR GREATER THAN 0.1 OF THE PRODUCT IS LISTED BY OSHA,
NTP, OR IARC AS A SUSPECT CARCINOGEN.

EMERGENCY AND FIRST AID PROCEDURES:
EYES: IF EYE IRRITATION OCCURS, FLUSH WITH WATER FOR AT LEAST 15 MINUTES.
SEEK MEDICAL ATTENTION.

SKIN: IF MOLTEN ADHESIVE/MASTIC CONTACTS SKIN, COOL IMMEDIATELY IN WATER. DO
NOT ATTEMPT TO REMOVE MATERIAL FROM THE SKIN - TREAT AS A BURN AND SEEK
MEDICAL ATTENTION.

INGESTION: NOT A NORMAL ROUTE OF EXPOSURE. IF SWALLOWED, SEEK MEDICAL
ATTENTION.

INHALATION: REMOVE TO FRESH AIR. SEEK MEDICAL ATTENTION IF ANY BREATHING
PROBLEM DEVELOPS.


           ***SECTION VII: PRECAUTIONS FOR SAFE HANDLING AND USE***

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:

WASTE DISPOSAL METHOD: ALL PRODUCTS ARE CLASSIFIED AS NON-HAZARDOUS WASTE AND
SHOULD BE BURIED OR INCINERATED AT APPROVED SITES. IF THERE ARE LOCAL
REGULATIONS COVERING THE CONTROLLED INCINERATION OF HALOGENATED MATERIALS,
THEN ALL FLAME-RETARDED PRODUCTS, WITH THE EXCEPTION OF ZEROHAL TM, PRODUCTS
WILL BE SUBJECT TO SUCH REGULATIONS.  REFER TO THE PRODUCT LITERATURE FOR
IDENTIFICATION OF FLAME-RETARDED PRODUCTS.


PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING:
HEAT RESISTANT GLOVES ARE REQUIRED IF HOT PRODUCTS ARE HANDLED AFTER
INSTALLATION.

SPECIAL PRECAUTIONS: AVOID HEATING PRODUCTS BEYOND TEMPERATURES REQUIRED FOR
NORMAL INSTALLATION. SEE INSTALLATION INSTRUCTIONS FOR PROPER INSTALLATION
PROCEDURES. IF PRODUCTS CHAR OR BURN, IMMEDIATELY STOP HEATING. AVOID INHALING
ANY FUMES WHICH EVOLVE UNDER SUCH CIRCUMSTANCES. ALLOW ANY FUMES TO DISPERSE
AND VENTILATE BEFORE CONTINUING WORK IN THE AREA.

TRANSPORTATION:  THESE PRODUCTS ARE NON-HAZARDOUS UNDER DEPARTMENT OF
TRANSPORTATION REGULATIONS 49, CFR SECTION 171.8, IATA, IMD, AND AFR 71-4.
BECAUSE THERE ARE NO APPLICABLE SHIPPING REGULATIONS FOR THESE PRODUCTS,
LABELS ARE NOT REQUIRED ON THE OUTSIDE SHIPPING CONTAINER FOR THESE PRODUCTS
AND ALL PRODUCTS MAY BE SHIPPED THROUGH THE U.S POSTAL SERVICES.

INSTALLATION: FOLLOW APPROPRIATE INSTALLATION INSTRUCTIONS AND APPLICATIONS
GUIDES TO ENSURE THAT INSTALLATION IS PERFORMED PROPERLY. ENSURE THAT ANY
LOCAL REQUIREMENTS/LEGISLATION CONCERNING THE USE OF HAND-HELD ELECTRICAL
EQUIPMENT ARE OBSERVED. WHEN USING IR (INFRARED) HEATING DEVICES, OBSERVE
SPECIFIC INSTRUCTIONS. DO NOT TOUCH HOT SURFACES IN INSTALLATION EQUIPMENT.



                     ***SECTION VIII: CONTROL MEASURES***

RESPIRATORY PROTECTION (SPECIFY TYPE):

VENTILATION: IN ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE PRACTICE, ENSURE
VENTILATION ADEQUATE TO CONTROL EXPOSURES BELOW STATE AND FEDERAL PERMISSIBLE
LIMITS (PELS) DURING INSTALLATION.

PROTECTIVE CLOTHING AND EQUIPMENT: TO BE BASED ON THE OPERATION PERFORMED,
FOLLOWING OSHA, ANSI, OR NIOSH GUIDELINES. IF THERE IS A DANGER OF MOLTEN
ADHESIVE OR MASTIC CONTACTING THE SKIN OR EYES, USE EYE/FACE PROTECTION AND
HEAT RESISTANT GLOVES. IF THERE IS NECESSARY TO HANDLE GROSSLY OVERHEATED OR
FIRE-DAMAGED PRODUCTS, WEAR IMPERVIOUS GLOVES TO PREVENT POSSIBLE CONTACT WITH
POTENTIALLY CORROSIVE INORGANIC ACID RESIDUES. IF INSTALLATION OCCURS IN ALL
CONFINED, UNVENTILATED AREA, NIOSH/MSHA-APPROVED RESPIRATORS ARE RECOMMENDED.

WORK/HYGIENIC PRACTICES:

                    ***SECTION IX: SHIPPING REGULATIONS***

UN/NA NUMBER:
DOT HAZARD CLASS:
SHIPPING LABEL:
SHIPPING NAME:

                       ***SECTION X: SPECIAL COMMENTS***

THIS INFORMATION IS BELIEVED TO BE ACCURATE AND REPRESENTS THE BEST
INFORMATION CURRENTLY AVAILABLE TO US. HOWEVER, WE MAKE NO WARRANTY OF
MERCHANTABILITY OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WITH RESPECT TO
SUCH INFORMATION, AND WE ASSUME NO LIABILITY RESULTING FROM ITS USE. USERS
SHOULD MAKE THEIR OWN INVESTIGATION TO DETERMINE THE SUITABILITY OF THE
INFORMATION FOR THEIR PARTICULAR PURPOSES.

The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance.

© 2008 Imperial Supplies LLC Questions or comments? Contact us.