MSDS 9126

Permatex, Inc.
10 Columbus Blvd.
Hartford, CT 06106 USA
Telephone: 1-87-Permatex
(877) 376-2839
Emergency: 800-255-3924
International Emergency: 813-248-0585

                     Material Safety Data Sheet
1. PRODUCT IDENTIFICATION
Product Name:             PNEUMATIC-HYDRAULIC SEALANT 36 ML
Item No:                  54540
Product Type:             Anaerobic

2. COMPOSITION/INFORMATION ON INGREDIENTS
Component              Weight%            ACGIH TLV: TWA           OSHA PEL:
TETRAETHYLENE GLYCOL    30-50              Not Listed              Not Listed
HEXOATE
18268-70-7
                   
DIMETHACRYLATE ESTER    20-40              Not Listed              Not Listed
25852-47-5
                     
2-HYDROXYETHYL          20-40              Not Listed              Not Listed
METHACRYLATE
868-77-9
                                  
TREATED SILICON DIOXIDE,   <4             10 mg/m3 total           10 mg/m3 
SYNTHETIC, CRYSTALLINE-FREE               dust TLV                 Total dust
67762-90-7
                      
DIMETHYLBENZYL             <4              Not Listed              Not Listed
HYDROPEROXIDE
80-15-9
                      
PROPYLENE GLYCOL           <4              Not Listed              Not Listed
57-55-6


3. HAZARDS IDENTIFICATION
Toxicity:      May cause eye and skin irritation. May cause nose, throat and    
               respiratory irritation. Ingestion may irritate
               digestive tract and cause nausea, vomiting and diarrhea. Note:   
               This product does not contain microcyrstalline silica.
Primary Routes of Entry:  Eye and skin contact, ingestion, inhalation
Signs and Symptoms of Exposure:  May cause redness to eyes and irritation to    
               nasal passages. Repeated skin contact may cause allergic
               skin reactions.

Medical Conditions Recognized as       Preexisting skin disorders
Being Aggravated by Exposure:

4. FIRST AID MEASURES
Ingestion:     If swallowed, DO NOT induce vomiting. Keep individual calm.      
               Obtain medical attention.
Inhalation:    Move to fresh air in case of accidental inhalation of vapours.   
               Oxygen or artificial respiration if needed.
               Obtain medical attention.
Skin Contact:  Wash off with soap and water. If skin irritation persists, 
               call a physician.
Eye Contact:   In case of contact, immediately flush eyes with plenty of water  
               for at least 15 minutes and get medical attention if irritation  
              persists.


5. FIRE FIGHTING MEASURES
Flash Point (°F/C):     >200 degrees F  TCC
Recommended Extinguishing Media:  Carbon Dioxide, Dry Chemicals, Foam.
Special Fire-Fighting Procedures: Firefighters should wear self-contained       
                 breathing apparatus.
Hazardous Products of Combustion:  Oxides of carbon
Unusual Fire/Explosion Hazards:    None.

Lower Explosive Limit:    Not determined
Upper Explosive Limit:    Not determined
                                                                        
      
6. ACCIDENTAL RELEASE MEASURES
Spill Procedures:  Maintain good ventilation. Take up with an inert absorbent.  
                   Store in a closed waste container until disposal.


7. HANDLING AND STORAGE
Storage:          Store below 100 degrees F.
Handling:         Avoid prolonged skin contact. Keep away from eyes. Do not     
                  inhale vapors.

8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Eyes:             Safety glasses.
Skin:             Rubber or plastic gloves.
Ventilation:      General; local exhaust ventilation as necessary to control
                  any air contaminants to within their exposure
                  limits (or to the lowest feasible levels when limits have not 
                  been established) during the use of this product.
Respiratory Protection:  An approved respirator (i.e. NIOSH, etc.) should be    
                  worn when exposures are expected to exceed the
                  applicable limits.

9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance:              Purple liquid
Odor:                    MILD
Boiling Point:           >300°F
pH:                      Does not apply
Solubility in Water:     Slight
Specific Gravity:        1.00-1.15
VOC Content(Wt.%):       <4%
Vapor Pressure:          <5 mm Hg @ 25°C
Vapor Density (Air=1):   Heavier than air
Evaporation Rate:        Not Determined


10. STABILITY AND REACTIVITY
Chemical Stability:                Stable at normal conditions
Hazardous Polymerization:          MAY OCCUR.
Incompatabilities:                 Metal salts, heat and amines.
Conditions to Avoid:               Heat.
Hazardous Products of Combustion:  Oxides of carbon

11. TOXICOLOGICAL INFORMATION
See Section 3


12. ECOLOGICAL INFORMATION
No data available

13. DISPOSAL CONSIDERATIONS
Recommended Method of Disposal: Disposal should be made in accordance with
federal, state and local regulations.
US EPA Waste Number:   NH - Not a RCRA Hazardous Waste Material

14. TRANSPORTATION INFORMATION
DOT (49CFR 172)
Domestic Ground Transport
    DOT Shipping Name:    Unrestricted
    Hazard Class:         None
    UN/ID Number:         None
    Marine Pollutant:     None
                        
IATA
    Proper Shipping Name:     Not regulated
    Class or Division:        None
    UN/ID Number:             None
       
IMDG
    Proper Shipping:          Unrestricted
    Hazard Class:             None                          
    UN Number:                None
        
                        
15. REGULATORY INFORMATION
SARA 313 Chemicals: The following component(s) is listed as a SARA Section 313
Toxic Chemical.

DIMETHYLBENZYL HYDROPEROXIDE

CALIFORNIA PROP 65:
No California Prop 65 chemicals are known to be present at or above the No
Significant Risk Level.

TSCA Inventory Status:
Listed on Inventory: YES All components of this product are listed (or exempt)
on the EPA TSCA inventory.

16. OTHER INFORMATION
Estimated NFPA Rating:           HEALTH 2, FLAMMABILITY 1 , REACTIVITY 0.
Estimated HMIS Classification:   HEALTH 2, FLAMMABILITY 1, PHYSICAL HAZARD 0
NFPA is a registered trademark of the National Fire Protection Assn.
HMIS is a registered trademark of the National Paint and Coatings Assn.



Prepared By:     Denise Boyd, Manager-Environmental, Health & Safety            
                 Revision Date: February/26/2008
Company:         Permatex. Inc. 10 Columbus Blvd. Hartford, CT USA 06106        
                 Revision  1
                 Number:
Telephone No:    1-87-Permatex (877) 376-2839




                                 3 of 3

The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance.

© 2008 Imperial Supplies LLC Questions or comments? Contact us.