MSDS 7673

                                                   
                              LUBRIPLATE
                        MATERIAL SAFETY DATA SHEET
                                   Section 1
PRODUCT NAME OR NUMBER                      FORMULA
LUBRIPLATE No. 1500, 1550, 1551, 1552       Lithium Complex Soap, Mineral Oil   
                                            and Additives
GENERIC/CHEMICAL NAME:                      NSF H2 Registration No:
Petroleum Lubricating Grease                N/A

Manufacturer's Name                         Emergency Telephone Number
Fiske Brothers Refining Co.,                1-800-255-3924 CHEM-TEL (24 hour)
d/b/a LUBRIPLATE Lubricants Co.                
Address                                     Telephone Number for Information
1500 Oakdale Ave., Toledo, Ohio 43605 -     419-691-2491 - Toledo Office
129 Lockwood St., Newark, NJ 07105          

                      Section 2 ­ Composition/Information on Ingredients
Ingredients with CAS#'s               CAS #'s                Percentage
Mineral Oil                          64742-65-0                65 - 80%
Lithium Thickener                    7620-77-1                  3 - 10%
Dimethyl Ester                       106-79-6                    0 - 5%
E.P. Additive                        15874-48-3                  0 - 5%
Polybutene                           9003-29-6                  5 - 10%
Zinc Oxide                           1314-13-2                  5 - 10%

Hazardous Material Identification System (HMIS):       
Health - 1,      Flammability - 1,    Reactivity - 0
Not a Controlled Product under (WHMIS) - Canada    
Special Protection: See Section 9

                            Section 3 - Health Hazard Data
Threshold Limit Value 5 mg/m3 for oil mist in air. OSHA Regulation 29 CFR
1910.1000 - 0.5 mg/m3 for Antimony Compound (as Sb)

Effects of Overexposure Prolonged or repeated skin contact may cause skin
irritation. Product contacting the eyes may cause eye irritation.
Human health risks vary from person to person. As a precaution, exposure to
liquids, vapors, mists and fumes should be minimized. This
product has a low order of acute oral toxicity, but minute amounts aspirated
into the lungs during ingestion may cause mild to severe pulmonary injury.

Carcinogenicity:     NTP? No     IARC Monographs? No     OSHA Regulated? No

                        Section 4 - Emergency and First Aid Procedures
EYE CONTACT: Flush with clear water for 15 minutes or until irritation subsides.
If irritation persists, consult a physician.

SKIN CONTACT: Remove any contaminated clothing and wash with soap and warm
water. If injected by high pressure under skin,
regardless of the appearance or its size, contact a physician IMMEDIATELY. 
Delay may cause loss of affected part of the body.

INHALATION: Vapor pressure is very low and inhalation at room temperature is not
a problem. If overcome by vapor from hot product,
immediately remove from exposure and call a physician.

INGESTION: If ingested, call a physician immediately. Do not induce vomiting.

                           Section 5 - Fire and Explosion Hazard Data

Flash Point (Method Used)   COC - 500 degrees F      
Flammable Limits            LEL 0.9%     UEL 7.0%

Extinguishing Media    Foam, Dry Chemical, Carbon Dioxide or Water Spray (Fog)

Special Fire Fighting Procedures     Cool exposed containers with water. Use
air-supplied breathing equipment for enclosed or confined spaces.

Unusual Fire and Explosion Hazards   Do not store or mix with strong oxidants.
Empty containers retain residue. Do not cut, drill, grind, or weld, as they 
may explode.
                          
                           Section 6 - Physical/Chemical Characteristics

Boiling Point             > 550 degrees F       
Specific Gravity (H 2O = 1)                                  0.90 - 0.96

Vapor Pressure (mm Hg.)   < 0.01           Melting Point      Semi-solid

Vapor Density (AIR = 1)   >5               Evaporation Rate   < 0.01
                                          (Butyl Acetate = 1)
Solubility in Water       Negligible

Appearance and Odor       Tacky, off-white grease with mineral oil odor.

                                Section 7 - Reactivity Data

Stability     Unstable                     Conditions to Avoid      N/A
              Stable    X
Incompatibility (Materials to Avoid)  Avoid contact with strong oxidants
                                      like liquid chlorine, concentrated oxygen.

Hazardous Decomposition or Byproducts May form SO 2. If incomplete combustion,
Carbon Monoxide.

Hazardous Polymerization      May Occur        Conditions to Avoid N/A
                              Will Not Occur X

                           Section 8 - Spill or Leak Procedures

Steps to be taken in case material is released or spilled
Scrape up grease, wash remainder with suitable petroleum solvent or add
absorbent. Keep petroleum products out of sewers and water
courses. Advise authorities if product has entered or may enter sewers and water
courses.

Waste disposal method
Assure conformity with applicable disposal regulations. Dispose of absorbed
material at an approved waste disposal facility or site.

SARA/TITLE III, Section 313 Status -        Zinc Compounds - < 7%        
                                            Antimony Compounds - < 3%

                             Section 9 - Special Protection Information

Respiratory Protection (Specify type)        Normally not needed

Ventilation   Local Exhaust   Used to capture fumes and vapors    Special N/A
              Mechanical (General)                                Other N/A

Protective Gloves Use oil-resistant gloves, if needed.        
Eye Protection If chance of eye contact, wear goggles.

Other Protective Equipment         Use oil-resistant apron, if needed.

                             Section 10 - Special Precautions

Precautions to be taken in handling and storing
Keep containers closed when not in use. Do not handle or store near heat,
sparks, flame, or strong oxidants.

Other Precautions
Remove oil-soaked clothing and launder before reuse. Cleanse skin thoroughly
after contact.


The above information is furnished without warranty, expressed or implied,
except that it is accurate to the best knowledge of Fiske
Brothers Refining Co., d/b/a LUBRIPLATE Lubricants Co. The data on these sheets
relates only to the specific material designated
herein. Fiske Brothers Refining Co., d/b/a LUBRIPLATE Lubricants Co. assumes no
legal responsibility for use or reliance upon this data.


Date Prepared: June 21, 2007                 Prepared  by: James R. Kontak

The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance.

© 2008 Imperial Supplies LLC Questions or comments? Contact us.