Start an Order |
|
|
|
| Start an Order |
|||
| Home > Products > Chemicals & Paint > MSDS Sheets > MSDS 7630 -- [Back] | |||
|
MSDS 7630 7630: (DISCONTINUED)7631: Extreme Adhesive/Sealant 10.1 [12] MSDS Last updated: 10/22/2008
Material Safety Data Sheet
EcoGlue Extreme
1. Product and company identification
Product name : EcoGlue Extreme
Supplier : Eclectic Products Inc.
1075 Arrowsmith
Eugene, OR 97402
541-484-9621
Material uses : Industrial applications: Sealants
Manufacturer : Eclectic Products Inc.
1075 Arrowsmith
Eugene, OR 97402
541-484-9621
Code : Structural Sealant
Validation date : 3/24/2008.
Print date : 3/24/2008.
Responsible name : Regulatory Compliance
In case of emergency : CALL INFOTRAC
800-535-5053
001-352-323-3500
2. Hazards identification
Physical state : Liquid. [Paste.]
OSHA/HCS status : This material is considered hazardous by the OSHA Hazard
Communication Standard (29 CFR 1910.1200).
Emergency overview : WARNING !
CAUSES EYE IRRITATION. MAY CAUSE SKIN IRRITATION.
Severely irritating to eyes. Slightly irritating to the
skin. Do not get in eyes. Avoid breathing vapor or mist.
Avoid contact with skin and clothing. Wash thoroughly
after handling.
Routes of entry : Dermal contact. Eye contact. Inhalation.
Potential acute health effects
Inhalation : No known significant effects or critical hazards.
Ingestion : No known significant effects or critical hazards.
Skin : Slightly irritating to the skin.
Eyes : Severely irritating to eyes. Risk of serious damage to
eyes.
Potential chronic health effects
Chronic effects : No known significant effects or critical hazards.
Carcinogenicity : No known significant effects or critical hazards.
Mutagenicity : No known significant effects or critical hazards.
Teratogenicity : No known significant effects or critical hazards.
Developmental effects : No known significant effects or critical hazards.
Fertility effects : No known significant effects or critical hazards.
Over-exposure signs/symptoms
Inhalation : No specific data.
Ingestion : No specific data.
Skin : Adverse symptoms may include the following:
irritation
redness
Eyes : Adverse symptoms may include the following:
pain or irritation
watering
redness
Medical conditions : None known.
aggravated by over-
exposure
See toxicological information (section 11)
3. Composition/information on ingredients
Name CAS number %
Amino Silane 1760-24-3 1-5
There are no ingredients or additional ingredients present which, within the
current knowledge of the supplier and in the concentrations applicable, are
classified as hazardous to health or the environment and hence require
reporting in this section.
4. First aid measures
Eye contact : Immediately flush eyes with plenty of water for at least 15
minutes, occasionally lifting the upper and lower eyelids.
Check for and remove any contact lenses. Get medical
attention. Chemical burns must be treated promptly by a
physician.
Skin contact : Flush contaminated skin with plenty of water. Remove
contaminated clothing and shoes. Continue to rinse for at
least 10 minutes. Get medical attention if symptoms
occur. Wash clothing before reuse. Clean shoes thoroughly
before reuse.
Inhalation : Move exposed person to fresh air. Keep person warm and at
rest. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or
oxygen by trained personnel. It may be dangerous to the
person providing aid to give mouth-to- mouth resuscitation.
Get medical attention if adverse health effects persist or
are severe. If unconscious, place in recovery position and
get medical attention immediately. Maintain an open airway.
Loosen tight clothing such as a collar, tie, belt or
waistband.
Ingestion : Wash out mouth with water. Remove dentures if any. Move
exposed person to fresh air. Keep person warm and at rest.
If material has been swallowed and the exposed person is
conscious, give small quantities of water to drink.
Stop if the exposed person feels sick as vomiting may be
dangerous. Do not induce vomiting unless directed to do
so by medical personnel. If vomiting occurs, the head should
be kept low so that vomit does not enter the lungs. Get
medical attention if adverse health effects persist or are
severe. Never give anything by mouth to an unconscious
person. If unconscious, place in recovery position and get
medical attention immediately. Maintain an open airway.
Loosen tight clothing such as a collar, tie, belt or
waistband.
Protection of first-aiders : No action shall be taken involving any personal
risk or without suitable training. It may be
dangerous to the person providing aid to give mouth-to-mouth
resuscitation.
Notes to physician : No specific treatment. Treat symptomatically. Contact
poison treatment specialist immediately if large quantities
have been ingested or inhaled.
5. Fire-fighting measures
Flammability of the product : In a fire or if heated, a pressure increase will
occur and the container may burst.
Extinguishing media
Suitable : Use an extinguishing agent suitable for the surrounding
fire.
Not suitable : None known.
Special exposure hazards : Promptly isolate the scene by removing all persons
from the vicinity of the incident if there is a fire. No
action shall be taken involving any personal risk or
without suitable training.
Hazardous combustion: No specific data
products
Special protective : Fire-fighters should wear appropriate protective equipment
equipment for and self-contained breathing apparatus (SCBA) with a
fire-fighters full face-piece operated in positive pressure mode.
Special remarks on fire : Non-flammable.
hazards
6. Accidental release measures
Personal precautions : No action shall be taken involving any personal risk or
without suitable training.
Evacuate surrounding areas. Keep unnecessary and
unprotected personnel from entering. Do not touch or
walk through spilled material. Avoid breathing vapor or
mist. Provide adequate ventilation. Wear appropriate
respirator when ventilation is inadequate. Put on
appropriate personal protective equipment
(see section 8).
Environmental precautions : Avoid dispersal of spilled material and runoff and
contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the
product has caused environmental pollution (sewers,
waterways, soil or air).
Large spill : Stop leak if without risk. Move containers from spill
area. Approach release from upwind. Prevent entry into
sewers, water courses, basements or confined areas.
Wash spillages into an effluent treatment plant or
proceed as follows. Contain and collect spillage with
non-combustible, absorbent material e.g. sand,
earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations
(see section 13). Dispose of via a licensed waste
disposal contractor. Contaminated absorbent material may
pose the same hazard as the spilled product. Note: see
section 1 for emergency contact information and section
13 for waste disposal.
Small spill : Stop leak if without risk. Move containers from spill
area. Dilute with water and mop up if water-soluble or
absorb with an inert dry material and place in an
appropriate waste disposal container. Dispose of via a
licensed waste disposal contractor.
7. Handling and storage
Handling : Put on appropriate personal protective equipment (see
section 8). Eating, drinking and smoking should be
prohibited in areas where this material is handled,
stored and processed. Workers should wash hands and face
before eating, drinking and smoking. Do not breathe vapor
or mist. Do not ingest. Avoid contact with eyes, skin and
clothing. Keep in the original container or an approved
alternative made from a compatible material, kept tightly
closed when not in use. Empty containers retain product
residue and can be hazardous. Do not reuse container.
Storage : Store in accordance with local regulations. Store in
original container protected from direct sunlight in a
dry, cool and well-ventilated area, away from
incompatible materials (see section 10) and food and
drink. Keep container tightly closed and sealed until
ready for use. Containers that have been opened must be
carefully resealed and kept upright to prevent leakage.
Do not store in unlabeled containers. Use appropriate
containment to avoid environmental contamination.
8. Exposure controls/personal protection
Consult local authorities for acceptable exposure limits.
Recommended monitroing: If this product contains ingredients with exposure
procedures limits, personal, workplace atmosphere or biological
monitoring may be required to determine the
effectiveness of the ventilation or other control
measures and/or the necessity to use respiratory
protective equipment.
Engineering measures: No special ventilation requirements. Good general
ventilation should be sufficient to control worker
exposure to airborne contaminants. If this
product contains ingredients with exposure limits, use
process enclosures, local exhaust ventilation or other
engineering controls to keep worker exposure below any
recommended or statutory limits.
Hygiene measures: Wash hands, forearms and face thoroughly after handling
chemical products, before eating, smoking and using the
lavatory and at the end of the working period.
Appropriate techniques should be used to remove
potentially contaminated clothing. Wash contaminated
clothing before reusing. Ensure that eyewash stations
and safety showers are close to the workstation
location.
Personal protection
Respiratory : Use a properly fitted, air-purifying or air-fed
respirator complying with an approved standard if a
risk assessment indicates this is necessary.
Respirator selection must be based on known or
anticipated exposure levels, the hazards of
the product and the safe working limits of the selected
respirator.
Hands : Chemical-resistant, impervious gloves complying with an
approved standard should be worn at all times when
handling chemical products if a risk assessment
indicates this is necessary.
: Safety eyewear complying with an approved standard
should be used when a risk assessment indicates this is
necessary to avoid exposure to liquid splashes, mists,
gases or dusts.
Skin : Personal protective equipment for the body should be
selected based on the task being performed and the
risks involved and should be approved by a specialist
before handling this product.
Environmental exposure: Emissions from ventilation or work process equipment
should be checked to ensure they comply with the
requirements of environmental protection legislation.
In some cases, controls fume scrubbers, filters or
engineering modifications to the process equipment will
be necessary to reduce emissions to acceptable levels.
9. Physical and chemical properties
Physical state : Liquid. [Paste.]
Flash point : Not available.
Color : White.
Odor : Not available.
Specific gravity : 1.39
Estimated Vapor Density : >1 [Air = 1]
VOC % : 1.78%
To convert % VOC to lbs/gal use the following
equation:
Specific Gravity*8.33*VOC%=VOC lbs/gal
Evaporation rate : Not applicable.
10 . Stability and reactivity
Stability : The product is stable. Under normal conditions of
storage and use, hazardous polymerization will not
occur.
Conditions to avoid : No specific data.
Materials to avoid : No specific data.
Hazardous decomposition : Under normal conditions of storage and use, hazardous
products. decomposition products should not be produced.
Hazardous polymerization : Will not occur.
Conditions of reactivity : Non-flammable.
11 . Toxicological information
Acute toxicity
Product/ingredient name Result Species Dose Exposure
Amino Silane LD50 Oral Rat 7460 uL/kg -
LDLo Dermal Rabbit 16 mL/kg -
Carcinogenicity
IDLH : Not available
Synergistic products : Not available.
12. Ecological Information
Environmental effects : No known significant effects or critical hazards
Aquatic ecotoxicity
Conclusion/Summary : Not available.
Biodegradability
Conclusion/Summary : Not available.
13 . Disposal considerations
Waste disposal : The generation of waste should be avoided or minimized
wherever possible. Dispose of surplus and
non-recyclable products via a licensed waste
disposal contractor. Disposal of this product,
solutions and any by-products should at all
times comply with the requirements of environmental
protection and waste disposal legislation and any
regional local authority requirements. Avoid dispersal
of spilled material and runoff and contact with soil,
waterways, drains and sewers.
Disposal should be in accordance with applicable regional, national and local
laws and regulations.
Refer to Section 7: HANDLING AND STORAGE and Section 8: EXPOSURE
CONTROLS/PERSONAL PROTECTION for additional handling information and protection
of employees.
14 . Transport information
Regulatory UN Proper shipping Classes PG* Label Additional
information number name information
DOT Classification Not - - - -
regulated.
TDG Classification Not - - - -
regulated.
IMDG Class Not - - - -
regulated.
IATA-DGR Class Not - - - -
regulated.
PG* : Packing group
15 . Regulatory information
United States inventory (TSCA 8b): All components are listed
or exempted.
SARA 311/312 - Acute
Canada
WHMIS (Canada) : Class D-2B: Material causing other toxic effects (Toxic).
Canadian lists : CEPA Toxic substances: None of the components are listed.
Canadian NPRI: None of the components are listed.
Canada inventory : Canada inventory: All components are listed or exempted.
This product has been classified according to the hazard criteria of the CPR and
the MSDS contains all the information required by the CPR.
Mexico
Classification :
0 Flammability
0 Health
0 Reactivity
Special
EU regulations
Risk phrases : This product is not classified according to EU
legislation.
International regulations
International lists: Australia inventory (AICS): All components are listed
or exempted.
China inventory (IECSC): All components are listed or
exempted.
Korea inventory (KECI): All components are listed or
exempted.
Philippines inventory (PICCS): All components are listed
or exempted.
Japan inventory (ENCS): Not determined.
16 . Other information
Hazardous Material :
Information System (U.S.A.)
Health 1
Flammability 0
Physical hazards 0
Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing
minimal hazards or risks, and 4 representing significant hazards or risks
Although HMIS® ratings are not required on MSDSs under 29 CFR 1910.1200, the
preparer may choose to provide them. HMIS® ratings are to be used
with a fully implemented HMIS®program. HMIS® is a registered mark of the
National Paint & Coatings Association (NPCA). HMIS® materials may
be purchased exclusively from J. J. Keller (800) 327-6868.
The customer is responsible for determining the PPE code for this material.
National Fire Protection :
Association (U.S.A.)
Flammability 0
Health 0
Instability 0
Special
Date of printing : 3/24/2008.
Date of issue : 3/24/2008.
Date of previous issue : 12/5/2007.
Version : 1.01
Indicates information that has changed from previously issued version.
Notice to reader
To the best of our knowledge, the information contained herein is accurate.
However, neither the above-named supplier, nor any of its subsidiaries, assumes
any liability whatsoever for the accuracy or completeness of the
information contained herein.
Final determination of suitability of any material is the sole responsibility
of the user. All materials may present unknown hazards and should be used with
caution. Although certain hazards are described herein, we cannot
guarantee that these are the only hazards that exist.
6/6
3/24/2008.
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance. For more product information by email, click here Imperial Supplies LLC does not provide services and products outside the United States |
Printer-Friendly View
