Start an Order |
|
|
|
| Start an Order |
|||
| Home > Products > Chemicals & Paint > MSDS Sheets > MSDS 7572 -- [Back] | |||
|
MSDS 7572 7572: Anti Corrosion Gel 3 Oz Tube [1]MSDS Last updated: 09/15/2005
SYNCO
Material Safety Data Sheet U.S. Department of Labor
May be used to comply with Occupational Safety and Health
Administration
OSHA's Hazard Communication Standard (Non-Mandatory Form)
29 CFR 1910.1200. Standard must be consulted Form Approved
for specific requirements. OMB No. 1218-0072
IDENTITY Note: Blank spaces are not permitted.
If any item is not applicable, or no
information is available, the space must
be marked to indicate that.
CORROSION AND CONNECTOR GEL
Part Numbers - 82003, 82016
SECTION 1
--------------------------------------------------------------------------------
Manufacturer's Name: SYNCO CHEMICAL CORPORATION
Address: 24 DaVINCI DRIVE
BOHEMIA, NY 11716
Emergency Telephone Number: 800-424-9300
Telephone Number for Information; 631-567-5300
Date Prepared; January 1, 2005
Signature of Preparer (Optional):
SECTION II - HAZARDOUS INGREDIENTS/IDENTITY INFORMATION
Other Limits
--------------------------------------------------------------------------------
Hazardous OSHA ACGIH Recommended Percentages
Components PEL TLV
(Specific Chemical/Identity; Common Name(s)
Synthetic Hydrocarbons CAS#68037-01-4 70-80%
Hydro Treated Polymer CAS#8042-47-5 10-20%
Fumed Silica CAS#68611-44-9 7-10%
Anti-Oxidant CAS#41484-35-9 1-2%
C11-14 Branched
Alyklamines CAS#80939-62-4 .5-1.5%
Barium Petroleum
Sulfonate CAS#61790-48-5 .1-.25%
Thermal Stabilizer CAS#68648-89-5 3-5%
Unamine O CAS#27136-73-8 .25-1%
Polyglycol CAS#025322-69-4 1-2%
All ingredients are TSCA listed.
SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS
--------------------------------------------------------------------------------
Boiling Point N/A Specific Gravity (H2O=1) .89
Vapor Pressure (mm Hg.) N/A Melting Point N/A
Vapor Density (AIR=1) N/A Evaporation Rate (Butyl Acetate=1) N/A
Solubility in Water: NOT SOLUBLE
Appearance and Odor: OLIVE GREEN COLOR, SLIGHT ODOR
SECTION IV - FIRE AND EXPLOSION HAZARD DATA
--------------------------------------------------------------------------------
Flash Point (Method used) N/A Flammable Limits LEL UEL
Extinguishing Media; CARBON DIOXIDE, DRY CHEMICAL, FOAM
Special Fire Fighting Procedures; WATER MAY BE INEFFECTIVE BUT CAN BE USED TO
COOL CONTAINERS EXPOSED TO HEAT OR FLAME. CAUTION SHOULD BE EXERCISED WHEN USING
WATER OR FOAM AS FROTHING MAY OCCUR.
Unusual Fire and Explosion Hazards; DENSE SMOKE MAY BE GENERATED WHILE BURNING
CARBON MONOXIDE. CARBON DIOXIDE AND OTHER OXIDES MAY BE GENERATED AS PRODUCTS
OF COMBUSTION.
SECTION V - REACTIVITY DATA
--------------------------------------------------------------------------------
Stability: Unstable; Conditions to avoid;
Stable: YES Conditions to avoid: NONE KNOWN
Incompatibility (materials to avoid): MAY REACT WITH STRONG OXIDIZING
AGENTS.
Hazardous Decomposition or Byproducts
Hazardous Polymerization:May occur; Conditions to avoid;
Will not occur:YES Conditions to avoid: NONE KNOWN
SECTION VI - HEALTH HAZARD DATA
--------------------------------------------------------------------------------
Route(s) of Entry: INHALATION? SKIN? INGESTION?
Health Hazards (Acute and Chronic): EYE; THIS PRODUCT IS MINIMALLY IRRITATING
TO EYES UPON DIRECT CONTACT. SKIN: SLIGHT IRRITATION.
Carcinogenicity: NTP? NOT LISTED IARC MONOGRAPHS? NOT LISTED
OSHA REGULATIONS? NOT LISTED
Signs and Symptoms of Exposure: CONTACT WITH EYE MAY RESULT IN SLIGHT
IRRITATION. PROLONGED OR REPEATED SKIN CONTACT MAY CAUSE MILD IRRITATIONS.
Medical Conditions Generally Aggravated by Exposure; N/E
Emergency and First Aid Procedures; SKIN; REMOVE BY WIPING AND WASH WITH SOAP
AND WATER.
EYES; WASH WITH COPIOUS AMOUNTS OF WATER.
INHALATION; REMOVE TO OPEN AIR.
SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE
--------------------------------------------------------------------------------
Steps to be Taken in Case Material is Released of Spilled; SPILLS SHOULD BE
ABSORBED OR SCRAPED UP.
Waste Disposal Method; USE METHOD OUTLINED IN LOCAL EPA AND GOVERNMENTAL
REGULATIONS. CONTACT YOUR LOCAL OFFICE.
Precautions to be Taken in Handling and Storage; KEEP CONTAINERS CLOSED. GOOD
MANUFACTURING PRACTICES SHOULD BE FOLLOWED IN HANDLING AND STORAGE.
Other Precautions; SURFACE SUBJECT TO SPILLS WITH THIS PRODUCT CAN BECOME
SLIPPERY.
SECTION VIII - CONTROL MEASURES
--------------------------------------------------------------------------------
Respiratory Protection (Specify Type): NONE REQUIRED
Ventilation Local Exhaust N/A Special; N/A
Mechanical (General) N/A Other; N/A
Protective Gloves; YES Eye Protection; YES
Other Protective Clothing or Equipment: EYE BATH AND SAFETY SHOWER
Work Hygienic Practices; NORMAL PRECAUTIONS COMMON TO GOOD MANUFACTURING
PRACTICES SHOULD BE FOLLOWED.
The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance. For more product information by email, click here Imperial Supplies LLC does not provide services and products outside the United States |
Printer-Friendly View
