MSDS 5190-4

MATERIAL SAFETY DATA SHEET

SPILFYTER® Products                     Revision Date: 07/25/05
M Series Sorbents                            MSDS No. 1012

SECTION 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Number: M Series
Product Name: PREMIUM OIL ONLY Sorbent Products.

Manufacturer:               Emergency Telephone Numbers:
NPS Corporation             CHEMTREC-- Domestic      (800)  424-9300 24 hrs.
3303 Spirit Way                     -- International (202)  483-7616 24 hrs.
Green Bay, WI 54304         Information (800) 558-5066 7:30am-4:30pm CDT  M-F
                                                                    
                                     
SECTION 2. COMPOSITION/INFORMATION ON INGREDIENTS
CAS Registry #         Component
9003-07-0              Polypropylene Particulate or Fabric        99.7 %
                       Blue Pigment                               0.3 %

(NOTE: See Section 8 of this MSDS for Exposure Guidelines)

SECTION 3. HAZARDS IDENTIFICATION

                 Emergency Overview
Odorless, white or colored fabric or particulate. This material presents little
or no hazard if spilled and exhibits no unusual fire hazard.

Potential Health Effects
      Eye: Direct contact may cause irritation.
      Inhalation: Exposure to dust levels exceeding the PEL (see Section 8) may
cause irritation of the upper respiratory system. Breathing dust may aggravate
acute or chronic asthma or other chronic pulmonary diseases.
      Signs and Symptoms:
      . Eyes: Redness, Tearing
      . Inhalation: Dry cough, labored breathing during exertion.

SECTION 4. FIRST AID MEASURES
      Eyes: Immediately flush with plenty of water for at least 15 minutes. If
irritation persists, seek medical attention.
      Skin: Brush off excess fibers with dry towel. Wash affected area with
plenty of soap and water for several minutes. If skin irritation develops or
persist, seek medical attention.
      Inhalation: Remove to fresh air. If not breathing, give artificial
respiration. If breathing is difficult, give oxygen. Seek medical attention.
NOTE: If burned through contact with molten material, cool as quickly as
possible with water and seek medical attention. Do not attempt to remove the
cooled molten material.

SECTION 5. FIRE FIGHTING MEASURES
      Flash Point:  >625 degrees F
      Flammable Limits:  N/A
      Auto-ignition Temperature:  >675 degrees F
NOTE: This material will burn, but it is difficult to ignite.
      Extinguishing Media:  Water spray, ABC dry chemical, foam, or carbon
                            dioxide. Use water fog or spray to cool exposed     
                       equipment and containers.
      Special Fire Fighting Procedures:  For large fire or fires in confined
                            areas, full emergency equipment with
                            self-contained breathing apparatus and
                            full protective clothing should be used.
                            Thermal decomposition of this product
                            may produces hazardous and irritating gases. See    
                        Section 10.


SECTION 6. ACCIDENTAL RELEASE MEASURES
      Unused material can be shoveled, swept, or vacuumed and recycled for use.
Avoid generating airborne dust.


      If used material is released or spilled, see Section 13.

SECTION 7. HANDLING AND STORAGE
      Store at room temperature in a dry area. When handling, avoid the
generation of airborne dust. Storage for extended periods (>30 days) at
temperatures >150 degrees F may cause decomposition. This material produces an
electrostatic accumulation hazard. Use proper grounding/bonding procedures.

SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION
      Exposure Limits: None specifically developed for this product: treated as
a nuisance dust as defined in 29 CFR 1910.1000.
      OSHA PEL: Total Dust is 15 mg/M3.
                Respirable Fraction is 5 mg/M3.
      ACGIH TLV is 10 mg/M3.

      The end-user must determine the specific types of personal protective
equipment needed according to 29 CFR 1910.132-Personal Protective Equipment
(PPE) for General Industry. The following are only suggestions:
      . Eyes; Safety glasses or goggles
      . Skin: Work gloves

Adequate ventilation should be provided to limit the amount of airborne dust.

SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
      Appearance:  White or colored fabric or particulate
      Odor: Odorless          Evaporation Rate (Butyl Acetate=1): NA
      Boiling Point: NA       % Vaporizable by volume (H2O=100): <0.4
      Vapor Pressure (mmHg):  NA
      Vapor Density:  NA
      Solubility in Water: Insoluble
      Specific Gravity (H2O=1):  0.90
      Melting Point:  >320 degrees F
      pH:  NA

SECTION 10. STABILITY AND REACTIVITY
      Stable: Yes
      Conditions to Avoid: See Section 7
      Incompatibility (Materials to Avoid): Avoid contact with hot or
concentrated nitric and perchloric acids, and fuming sulfuric acid at
temperatures >140 degrees F.
      Hazardous Decomposition or Byproducts: Thermal decomposition produces
carbon monoxide, carbon dioxide, methane, acetone, and other ketones.
      Hazardous Polymerization:  Will not occur

SECTION 11. TOXICOLOGICAL INFORMATION
      This product is not listed by NTP or IARC. See Section 15.

SECTION 12. ECOLOGICAL INFORMATION
      No data available. See Section 15.

SECTION 13. DISPOSAL CONSIDERATIONS
      This product in itself is considered to be non-hazardous as defined by
RCRA (40 CFR 261). Once used, this product will take on the characteristics of
the chemical sorbet and should be disposed of accordingly.
Disposal of this product (used or unused) must be in compliance with all local,
state, and federal regulations.

SECTION 14. TRANSPORT INFORMATION
      This product is not a DOT Hazardous Material and is not regulated for all
shipping purposes.

SECTION 15. REGULATORY INFORMATION
      This product does not meet the definition of a hazardous chemical given
in 29 CFR 1910.1200 (OSHA).
      TSCA Inventory Status: All components are listed on the TSCA list.
      SARA Title III
            Section 302 Extreme Hazardous Substance List: Not listed
            Section 311/312 Hazard Classification.
                 Immediate (acute): No
                 Delayed (chronic): No
                 Fire: No
                 Sudden Release of Pressure: No
                 Reactive: No
            Section 313 Toxic Chemicals: Not listed
      USEPA CERCLA -Reportable Quantity (RQ): Not listed
      RCRA Hazardous Waste: Not Listed
      State/Int'l Right-to-Know Regulations: Not listed

SECTION 16. OTHER INFORMATION
      Abbreviations:
            CFR: Code of Federal Regulations
            OSHA: Occupational Safety and Health Administration
            MSDS: Material Safety Data Sheet
            PEL: Permissible Exposure Limit
            NA: Not Applicable
            ACGIH: American Conference of Governmental, Industrial Hygienists.
            TLV: Threshold Limit Value
            NTP: National Toxicology Program
            IARC: International Agency for Research on Cancer
            RCRA: Resource Conservation and Recovery Act
            TSCA: Toxic Substances Control Act
            SARA: Superfund Amendments and Reauthorization Act
            USEPA: United States Environmental Protection Agency
            CERCLA: Comprehensive Response, Compensation, and Liability Act.
            DOT: Department of Transportation
            NFPA: National Fire Protection Association
            HMIS: Hazardous Material Information System

NFPA Ratings:                     HMIS Ratings:
Health: 0                         Health: 0
Fire: 1                           Flammability: 1
Reactivity: 0                     Reactivity: 0
Special Hazard: None              Personal Protection: NA

NOTE: This MSDS has been prepared only for the Premium Oil Only Sorbent
Products (M Series) of SPILFYTER® Products. The MSDS's of the chemicals used
with this product must be reviewed completely, and precautions taken as
described.

The information accumulated here in has been compiled from sources believed to
be reliable and is accurate to the best of our knowledge.
However, NPS Corporation cannot give guarantees regarding the information from
sources, and expressly does not make any warranties, nor assumes any liability
for its uses of this product.

Disclaimer:
You have purchased SPILFYTER® products from NPS Corporation.
You have been provided data, product labels, MSDS's , and other information
about SPILFYTER® Products.

Some SPILFYTER® Products are hazardous. Information about SPILFYTER® Products
that are hazardous is furnished without guarantee. NPS Corporation does not
guarantee the accuracy of the information about hazardous SPILFYTER® Products.

Those products are only to be used by people having expertise in using the
hazardous products.

The information provided about the hazardous products is believed to be
correct. You must perform your investigation as to the safety, toxicity,
suitability, and proper shipping method for any hazardous SPILFYTER®
Product.

No guarantee, expressed or implied, is made by NPS Corporation about the
results of use of its products. No guarantee is made as to the safety and
toxicity of any SPILFYTER® Product.

NPS Corporation does not assume any liability arising out of use of SPILFYTER®
Products. Additional information and research may be necessary before you use
the SPILFYTER® Products. NPS Corporation is not responsible for damages, direct
or indirect, resulting from the use of SPILFYTER® Products or from reliance on
data in the MSDS or product label.

If you resell SPILFYTER® Products, you must, by law, furnish your customers a
copy of MSDS's and handling instructions.

You are also required by law to insure that all SPILFYTER® Products are
properly shipped.

SPILFYTER®, KOLLECT-A-KEM®, HANDS-IN-BAG®, KOLORSAFE®,
And GRAB&GO® are all registered trademarks of NPS Corporation.
AQUALOCKIT, TRUK-KIT, DRAINGUARDGAPSEAL, MEDICLEAN, and TIDYMAT,  are all
trademarks of NPS Corporation.

                 Copyright 2002, NPS Corporation

The information contained in this MSDS was obtained from current and reliable sources, however, the data is provided without any warrenty, expressed or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of Imperial Supplies LLC, Imperial will not be responsible for loss, injury, or expense arising out of the products improper use. No warranty, expressed or inferred, regarding the product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance.

© 2008 Imperial Supplies LLC Questions or comments? Contact us.